PILINBPQ w/Signal Link USB

Brett Williams · 2022-06-14T08:55:09-07:00

Group, is anyone using a Signal Link USB with a PILINBPQ setup? I have tried some pre-made port configs, non seemed to work. Thanks for the help.. Brett KB5YZB

PILINBPQ w/Signal Link USB

Brett Williams All Messages By This Member #35271 Group, is anyone using a Signal Link USB with a PILINBPQ setup? I have tried some pre-made port configs, non seemed to work.? Thanks for the help.. Brett KB5YZB
Al Gordon #35273 开云体育 I have, but I took my station down recently due to moving QTH, and am not sure when it will be back online. In other words: I don’t have the config handy to share. At a high level however, the important thing to understand with SignaLink USB with PILINBPQ is that you’re configuring Direwolf (or other soundmodem) for VOX, and you need to make sure that you get your audio levels set high enough to trigger the SignaLink, but not so high that you’re splattering. You probably will need to run something like “alsamixer” (command line audio level configuration “GUI”), and tweak the knobs on the SignaLink USB to get the right TX and RX audio. The Delay knob on the SignaLink USB should probably be cranked all the way to the left (no delay). I hope this helps. 73 de K7AJG . . toggle quoted message Show quoted text On Jun 5, 2022, at 12:10 PM, Brett Williams <KB5YZB@...> wrote: Group, is anyone using a Signal Link USB with a PILINBPQ setup? I have tried some pre-made port configs, non seemed to work.? Thanks for the help.. Brett KB5YZB
John G8BPQ All Messages By This Member #35274 开云体育 Which modem are you trying to use with the Signallink? 73, John On 05/06/2022 17:10, Brett Williams wrote: toggle quoted message Show quoted text Group, is anyone using a Signal Link USB with a PILINBPQ setup? I have tried some pre-made port configs, non seemed to work.? Thanks for the help.. Brett KB5YZB
Ben Kuhn All Messages By This Member #35275 I'm not at home right now so I can't access my configuration, but the other thing needed to make it work right is to set the delay pot as low as possible.? If the delay is up to high you will transmit okay but your radio will still be transmitting when the answering station responds.? If you have CAT control another solution is to remove the PTT jumper in the Signalink and use CAT for PTT. toggle quoted message Show quoted text On Sun, Jun 5, 2022, 16:01 Al Gordon <al@...> wrote: I have, but I took my station down recently due to moving QTH, and am not sure when it will be back online. In other words: I don’t have the config handy to share. At a high level however, the important thing to understand with SignaLink USB with PILINBPQ is that you’re configuring Direwolf (or other soundmodem) for VOX, and you need to make sure that you get your audio levels set high enough to trigger the SignaLink, but not so high that you’re splattering. You probably will need to run something like “alsamixer” (command line audio level configuration “GUI”), and tweak the knobs on the SignaLink USB to get the right TX and RX audio. The Delay knob on the SignaLink USB should probably be cranked all the way to the left (no delay). I hope this helps. 73 de K7AJG . . On Jun 5, 2022, at 12:10 PM, Brett Williams <KB5YZB@...> wrote: Group, is anyone using a Signal Link USB with a PILINBPQ setup? I have tried some pre-made port configs, non seemed to work.? Thanks for the help.. Brett KB5YZB
Brett Williams All Messages By This Member #35276 开云体育 UZ7HO. But I'm not sold only to that as it is the only one I used.... Brett On 6/5/2022 3:13 PM, John G8BPQ wrote: toggle quoted message Show quoted text Which modem are you trying to use with the Signallink? 73, John On 05/06/2022 17:10, Brett Williams wrote: Group, is anyone using a Signal Link USB with a PILINBPQ setup? I have tried some pre-made port configs, non seemed to work.? Thanks for the help.. Brett KB5YZB
John G8BPQ All Messages By This Member #35278 开云体育 A normal UZ7HO port definition is PORT ?ID=UZ7HO ?DRIVER=UZ7HO ?CHANNEL=A ?INTERLOCK=4 ?PACLEN=100 ?CONFIG ? ADDR 127.0.0.1 8000 ? MAXSESSIONS=5 ? UPDATEMAP ENDPORT How are you running UZ7HO Soundmodem on a Pi? Or are you running my QtSoundModem? If you are running Soundmodem on a separate Windows machine, the ADDR line should have the IP address of the Windows machine in place of 127.0.0.1 Make sure that the AGWPE interface is enabled in the Soundmodem Devices menu, with the same port number as in the ADDR line. 73, John On 05/06/2022 23:16, Brett Williams wrote: toggle quoted message Show quoted text UZ7HO. But I'm not sold only to that as it is the only one I used.... Brett On 6/5/2022 3:13 PM, John G8BPQ wrote: Which modem are you trying to use with the Signallink? 73, John On 05/06/2022 17:10, Brett Williams wrote: Group, is anyone using a Signal Link USB with a PILINBPQ setup? I have tried some pre-made port configs, non seemed to work.? Thanks for the help.. Brett KB5YZB
Brett Williams All Messages By This Member #35283 开云体育 I would like to run everything on pi, So I would to try your QT Southmodem. What is config for your QT Soudmodem on the pi? Installing you QTSoundModem; I will follow your website institutions; if I run problem I will let you know..... On 6/5/2022 10:57 PM, John G8BPQ wrote: toggle quoted message Show quoted text A normal UZ7HO port definition is PORT ?ID=UZ7HO ?DRIVER=UZ7HO ?CHANNEL=A ?INTERLOCK=4 ?PACLEN=100 ?CONFIG ? ADDR 127.0.0.1 8000 ? MAXSESSIONS=5 ? UPDATEMAP ENDPORT How are you running UZ7HO Soundmodem on a Pi? Or are you running my QtSoundModem? If you are running Soundmodem on a separate Windows machine, the ADDR line should have the IP address of the Windows machine in place of 127.0.0.1 Make sure that the AGWPE interface is enabled in the Soundmodem Devices menu, with the same port number as in the ADDR line. 73, John On 05/06/2022 23:16, Brett Williams wrote: UZ7HO. But I'm not sold only to that as it is the only one I used.... Brett On 6/5/2022 3:13 PM, John G8BPQ wrote: Which modem are you trying to use with the Signallink? 73, John On 05/06/2022 17:10, Brett Williams wrote: Group, is anyone using a Signal Link USB with a PILINBPQ setup? I have tried some pre-made port configs, non seemed to work.? Thanks for the help.. Brett KB5YZB
John G8BPQ All Messages By This Member #35285 开云体育 The config is the same for Soundmodem and QtSoundModem. 73, John On 06/06/2022 18:55, Brett Williams wrote: toggle quoted message Show quoted text I would like to run everything on pi, So I would to try your QT Southmodem. What is config for your QT Soudmodem on the pi? Installing you QTSoundModem; I will follow your website institutions; if I run problem I will let you know..... On 6/5/2022 10:57 PM, John G8BPQ wrote: A normal UZ7HO port definition is PORT ?ID=UZ7HO ?DRIVER=UZ7HO ?CHANNEL=A ?INTERLOCK=4 ?PACLEN=100 ?CONFIG ? ADDR 127.0.0.1 8000 ? MAXSESSIONS=5 ? UPDATEMAP ENDPORT How are you running UZ7HO Soundmodem on a Pi? Or are you running my QtSoundModem? If you are running Soundmodem on a separate Windows machine, the ADDR line should have the IP address of the Windows machine in place of 127.0.0.1 Make sure that the AGWPE interface is enabled in the Soundmodem Devices menu, with the same port number as in the ADDR line. 73, John On 05/06/2022 23:16, Brett Williams wrote: UZ7HO. But I'm not sold only to that as it is the only one I used.... Brett On 6/5/2022 3:13 PM, John G8BPQ wrote: Which modem are you trying to use with the Signallink? 73, John On 05/06/2022 17:10, Brett Williams wrote: Group, is anyone using a Signal Link USB with a PILINBPQ setup? I have tried some pre-made port configs, non seemed to work.? Thanks for the help.. Brett KB5YZB
Brett Williams All Messages By This Member #35358 开云体育 Just an update; I now have QTsoundmodem working on PILINBPQ with USB Signalink. Thank you to John G8BPQ and Lee K5DAT Thank you gentlemen; it works very well. Brett KB5YZB On 6/5/2022 10:57 PM, John G8BPQ wrote: toggle quoted message Show quoted text A normal UZ7HO port definition is PORT ?ID=UZ7HO ?DRIVER=UZ7HO ?CHANNEL=A ?INTERLOCK=4 ?PACLEN=100 ?CONFIG ? ADDR 127.0.0.1 8000 ? MAXSESSIONS=5 ? UPDATEMAP ENDPORT How are you running UZ7HO Soundmodem on a Pi? Or are you running my QtSoundModem? If you are running Soundmodem on a separate Windows machine, the ADDR line should have the IP address of the Windows machine in place of 127.0.0.1 Make sure that the AGWPE interface is enabled in the Soundmodem Devices menu, with the same port number as in the ADDR line. 73, John On 05/06/2022 23:16, Brett Williams wrote: UZ7HO. But I'm not sold only to that as it is the only one I used.... Brett On 6/5/2022 3:13 PM, John G8BPQ wrote: Which modem are you trying to use with the Signallink? 73, John On 05/06/2022 17:10, Brett Williams wrote: Group, is anyone using a Signal Link USB with a PILINBPQ setup? I have tried some pre-made port configs, non seemed to work.? Thanks for the help.. Brett KB5YZB

Previous Topic Next Topic