Keyboard Shortcuts
ctrl + shift + ? :
Show all keyboard shortcuts
ctrl + g :
Navigate to a group
ctrl + shift + f :
Find
ctrl + / :
Quick actions
esc to dismiss
Likes
- Bpq32
- Messages
Search
|
Re: BPQ + NTS + Winlink Client EmComm help (sans Internet)
This was working after all. I was just not getting the yellow and
toggle quoted message
Show quoted text
green color codes in the web GUI like I do for personals and bulls. Thanks, Chris KQ6UP On Wed, May 3, 2023 at 8:54?AM Mark Taylor <mtaylor@...> wrote:
--
Thanks, Chris Maness |
|
NTS* and !NTSCA (will this kill a loop?)
I am noticing that some traffic may be looping because I have NTS* as
my outbound partner is the same as my inbound forwarding partner for NTSCA. I am wondering adding an exclamation mark in front of a "match" in BPQ. This works in FBB, not sure for BPQ. Thanks in advance, Chris KQ6UP -- Thanks, Chris Maness |
|
Re: Any recommended config for using Direwolf with LinBPQ?
This is my current Port config:
PORT
?PORTNUM=3
?ID=DirewolfVHF ;WinLink Gateway 145.030MHz
?TYPE=ASYNC
?PROTOCOL=KISS
?IPADDR=127.0.0.1
?TCPPORT=8001
?CHANNEL=A
?PACLEN=128
?TXDELAY=500
?FRACK=7000
?RESPTIME=1500
?MAXFRAME=4
?RETRIES=6
?SLOTTIME=100 ;add to remove error
?PERSIST=63 ;add to remove error
?WL2KREPORT PUBLIC, www.winlink.org, 8778, KO4NCC-10, EL98AU, 00-23, 145030000, PKT1200, 20, 20, 2, 0
ENDPORT I want to be able to have my gateway used as a digipeater for WinLink? so I want to add the following entries: DIGIFLAG=1 ;adding because I want to be able to be used as a digipeater
?DIGIPORT=0 ;digipeat on this same port that I received on
I'm just not sure if this isn't going to just digipeat everything or just the messages a user sends through my node as a digipeater. 73 KO4NCC Jeff
|
|
Re: PERMITTEDAPPLS not functioning in config files....
Good Morning John,
???? I think I may be a bit confused on your response, the only mode I have on HF is AX.25 300bps by way of Direwolf (via TCP) on another machine that handles the HF radio so I assume that is not considered a true "AX.25 port", but instead considered a TCP/IP port? Any chance that there is another way to limit that connection port for applications, or any plans of a new feature to add that ability? Port info below for reference, thanks. Greg - N3BYR PORT ?? ?PORTNUM=3 ?? ?ID=14.105 300 HF-PACKET ?? ?TYPE=ASYNC ?? ?PROTOCOL=KISS ?? ?KISSOPTIONS=NOPARAMS ?? ?PERMITTEDAPPLS=2,3 ?? ?FRACK=8000 ?? ?RESPTIME=3000 ?? ?RETRIES=5 ?? ?MAXFRAME=2 ?? ?PACLEN=32 ?? ?TXDELAY=400 ?? ?SLOTTIME=100 ?? ?PERSIST=64 ?? ?IPADDR=10.X.X.X ?? ?TCPPORT=8001 ENDPORT |
|
Re: PERMITTEDAPPLS not functioning in config files....
开云体育PERMITTEDAPPLS only affects incoming connects on ax.25 ports. It doesn't affect the list of applications that is displayed by the Node ? command73, John On 03/05/2023 22:52, Bruce Colburn via
groups.io wrote:
I seem to be running into an error where all the applications are listed on a port (in this case specifically the port assigned to HF) instead of only the permitted applications. Is there an additional item I need to add? to BPQ confi outside of the ports or other actions I need to take to make this function. In my port config for the HF port I have apps 2 and 3 listed (Chat and BBS), but the RMS and WEB are listed and available when I user connects to the node. For reference I am running under Linux Bullseye on a RaspPi, and running version 6.0.23.60 |
|
Re: Adding Digipeater path to IDMSG?
#llinbpq
开云体育No, it isn't possible to set a path for ID message.You can achieve a similar effect using beacons. 73, John On 04/05/2023 01:08, Jim - KI0BK via
groups.io wrote:
If its possible, how do I specify a digi path for the IDMSG?? My VHF port is port 1, and would like to have the IDMSG digi'd through another packet station. |
|
Re: Adding Digipeater path to IDMSG?
#llinbpq
开云体育Jim - if there is a way to do it with the IDMSG: directive in the
bpq32.cfg file I do not know or have long forgot how. My bpq32.cfg
simply contains *** I then set the text and a digi using either of two methods. Using the http gui is the recommended way by going to Ports and then selecting Beacons for the port involved which should provide a template to set the interval timing, the destination, any digi's, and the beacon text. The other not really recommended method that can work in a non http gui environment IF you are familiar with the file structure is to hand edit the UIUtil.cfg file although I suspect John may opt to not support doing this... 73 de Rich WA3WLH On 5/3/23 20:08, Jim - KI0BK via
groups.io wrote:
If its possible, how do I specify a digi path for the IDMSG?? My VHF port is port 1, and would like to have the IDMSG digi'd through another packet station. |
|
Adding Digipeater path to IDMSG?
#llinbpq
If its possible, how do I specify a digi path for the IDMSG?? My VHF port is port 1, and would like to have the IDMSG digi'd through another packet station.
Jim KI0BK |
|
Re: BPQ + NTS + Winlink Client EmComm help (sans Internet)
Yes, I have much of that going already, but I am not having luck with
the zip code in the to: field. I get matches say K6HTN lives in 91104, and she gets tons of messages. I forward her matches to a file (because we are still trying to get her setup), despite 91104 being set in my forward settings for her call, I have to manually go in and tag each piece of traffic to be forwarded. They don't automagically get tagged green like @NTS* does in the AT field. -Chris KQ6UP On Wed, May 3, 2023 at 8:54?AM Mark Taylor <mtaylor@...> wrote:
-- Thanks, Chris Maness |
|
PERMITTEDAPPLS not functioning in config files....
I seem to be running into an error where all the applications are listed on a port (in this case specifically the port assigned to HF) instead of only the permitted applications. Is there an additional item I need to add? to BPQ confi outside of the ports or other actions I need to take to make this function. In my port config for the HF port I have apps 2 and 3 listed (Chat and BBS), but the RMS and WEB are listed and available when I user connects to the node. For reference I am running under Linux Bullseye on a RaspPi, and running version 6.0.23.60
Greg - N3BYR |
|
Re: RMS Gateway Pi 3B replacement
From my experience, you can't take the sdcard from a "3b" and put it in
a "4" - it wont run ? Dave gm3yew - On Wed, 3 May 2023 12:33:00 -0500 "jdfiberops@..." <packet@...> wrote: I had to replace a failed Raspberry PI 3B on my RMS Gateway running |
|
Re: RMS Gateway Pi 3B replacement
On Wed, May 3, 2023 at 10:33 AM, jdfiberops@... wrote:
Not enough info to provide any definite answers, Your pi may now have a different IP address as each network interface has a unique MAC address which is used by the automatic IP DHCP service on your router to lend IPs out to the devices on your network. New hardware, new IP. This is all based on an assumption that you are using an automatically assigned IP address. 73 Red |
|
Re: IPGATEWAY with existing ampr-ripd gateway
#bpqconfig
#network
开云体育Thanks for the heads up! ? 73, ? Matt, WE1H ? Matt Atwood Merrimack, NH ? Phone / Text: 802-999-1994 Email: we1h@... Web: ? ? ? From: [email protected] <[email protected]> On Behalf Of kc9uhi@...
Sent: Tuesday, May 2, 2023 11:31 AM To: [email protected] Subject: Re: [bpq32] IPGATEWAY with existing ampr-ripd gateway #bpqconfig #network ? 44net is not 44.0.0.0/8 after the IP address sale a few years ago. Current proper routing netmask is a two parter - 44.0.0.0/9 and 44.128.0.0/10 -- 73, - Matt, WE1H we1h AT arrl.net http://www.we1h.com |
|
RMS Gateway Pi 3B replacement
开云体育I had to replace a failed Raspberry PI 3B on my RMS Gateway running bpq32 and now I can’t access the BPQ32 node page.? Removed the SD card from failed PI and placed into the new unit.? Is there a config on the new PI that I need to change? ? Thank you in advance. Jeff N9JXN |
|
Re: Node not showing in heard list
Just wanted to update this for others, John you were correct, Changing my IDMSG did the trick!
My config file has been corrected to: IDMSG:?????????????????????????????????????????? ; UI Node broadcast text Network node (KSOLA) ***????????????????????????????????????????????? ; Denotes end of IDMSG text TNX es 73 to the group Jim KI0BK |
|
Re: AXIP settings for hughes net
I second Rich's thoughts.? I have a link to a forwarding partner that uses a satellite internet connection.? Our connection had to be configured as a TCP link rather than UDP.? He is the TCP-Master and I am the TCP-Slave.
It is a stable link that is always on, and reconnects any time either of us reboots. Mark |
|
Re: Custom BBS Prompts
#bbs
开云体育Might be a nice enhancement ? ? ? From: [email protected] <[email protected]> On Behalf Of John G8BPQ
Sent: Wednesday, May 3, 2023 11:30 AM To: [email protected] Subject: Re: [bpq32] Custom BBS Prompts #bbs ? Matt, On 03/05/2023 15:24, Matt Atwood, WE1H wrote:
? -- 73, - Matt, WE1H we1h AT arrl.net http://www.we1h.com |
|
Re: BPQ + NTS + Winlink Client EmComm help (sans Internet)
Chris,
From memory so you may have to play around with these and read the documentation..... In your telnet config you should have the directives to be a Winlink gateway. CMS=1 CMSCALL=xxxxxx CMSPASS=xxxxxx Then you need to provide a relay directive... RELAYAPP=BBS Read up on FALLBACKTORELAY as that might be needed in your case. That will put all Winlink messages in the BBS where users can pick them up.? You may need an APPLICATION line to answer Winlink connections. For NTS messages it is just a matter of forwarding records. A zip code in the TO field will forward to that station and the station probably should be a NTS digital station expecting NTS messages. In the AT field you can put NTS* to forward all NTS messages, or you can use NTSxx where xx is a specific state to forward NTS messages for that state to a NTS digital station. There are most likely other ways to do this, I'm sure.? I actually run RMS Relay along side of one of my installs as it acts as a Local Post Office and I have not found a way for BPQ to completely simulate the actions of Relay. Using those hints you can probably get it working the way you want, and may get a few more hints from other users more experienced than me. 73, Mark |
|
Re: Custom BBS Prompts
#bbs
开云体育Matt,No, there is no way to customise prompts per user. 73, John On 03/05/2023 15:24, Matt Atwood, WE1H
wrote:
Hi All, |
Jeff
Red R. R. Tuby (PE1RRR)
to navigate to use esc to dismiss