开云体育

HF Transceiver, Power Supply, Manuals, and more For Sale: Yaesu FT-897 Transceiver: The FT-897 is basically a "do everything rig" covering DC to daylight with all modes. Features: * TX 160-10 Meters, 50 MHz, 144 MHz, 430-450 MHz * RX 100 kHz-56 MHz; 76-154 MHz; 420-470 MHz. * Power Output: 100 watts HF-6M, 50 watts 2 M, 20 watts 70 cm. * Operating Modes: USB, LSB, CW, AM, FM, Digital * Built-in 3-Message Memory Keyer * Multi-Color LCD Display. * Bar-Graph Metering of Power Output, ALC, SWR, Modulation * AGC * RF Gain/Squelch Control/IF Control. * Built-in Noise Blanker * Dual VFOs, Split Capability, IF Shift, and RIT * Built-in CW Electronic Keyer * Built-in CTCSS and DCS * Spectrum Scope * 200 Regular Memories * Alpha-Numeric Labeling of Memory Channels * CAT Control * 7.9 x 3.2 x 10.3 inches This one works as it should with no problems. Cosmetically it looks very close to new. No scratches. With paperwork for $750 . Yaesu FP-707, 20 Amp Speaker/Power Supply: The Yaesu FP-707 is a 20 amp 13.8 Volt DC Power Supply, with a very nice front facing speaker in the same enclosure. Cosmetically, it matches the FT-707, FT-747, FT-757 and likely others. Electrically, it can provide up to 20 amps, so will work with most any HF and/or VHF rig. It also has a set of binding posts on the back for easy connection of a rig in addition to the HF rig. The speaker has a 3.5 mm plug on it. This particular unit is in very good shape both electrically and cosmetically. I can not find a scratch, dent, or ding on it. Electrically, it works as it should. Buy this unit with manual for $125. . Yaesu NC-9 B Charger 13 V DC at 45 ma, 2.5 mm plug; $12 . Original Yaesu Manuals: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH-1B A2B speaker microphone, $2 SP-101 P, Speaker / Phone patch, $5 VX-1 dual band HT, $10 Maintenance Service Manual for Yaesu FT-208 R 2 meter HT. Looks new. $25 These are original Yaesu operating manuals only, in very nice condition. . I also have many other accessories available such as many different types of microphones, HTs, VHF and UHF rigs, HF and VHF/UHF antennas, connectors, miscellaneous accessories, etc. Just too many to list here. Please e-mail your requests. . Prices do not include shipping from Florida. Thanks. 73, Ken, W8EK Ken Simpson E-mail to W8EK@... or W8EK@... Voice Phone (352) 732-8400 .

Hello Is there ani info about the FV101dm repair, mine has a ofset of 400 Khz display is correct but signal out is 400 khz down i dident find any service manual for this unit Best rehards Hubert on6jz

Yaesu FT-707 HF Transceiver: The Yaesu FT-707 is an HF transceiver covering 80 to 10 meters in SSB, CW and AM modes. It does include the 30, 17 and 12 meter bands. Power input is 240 watts on SSB/CW and 80 watts on AM. It features a digital display and analog subdial. There is an LED meter. The FT-707 requires 13.5 VDC 20 Amps. This radio does not have general coverage receive. Features: 80-10 Meters Variable IF Bandwidth Noise Blanker 240 Watts Input Digital LED S/RF Meter VOX Cosmetically, this particular unit is in really great shape. Electrically, it could stand some work. It works fine on CW as it is. The digital readout stays at 0.000, but one can use the analog dial to read the frequency. The transmit audio seems nonexistent. Buy this unit, with paper work, for only $125. . Yaesu FP-707, 20 Amp Speaker/Power Supply: The Yaesu FP-707 is a 20 amp 13.8 Volt DC Power Supply, with a very nice front facing speaker in the same enclosure. Cosmetically, it matches the FT-707, FT-747, FT-757 and likely others. Electrically, it can provide up to 20 amps, so will work with most any HF and/or VHF rig. It also has a set of binding posts on the back for easy connection of a rig in addition to the HF rig. The speaker has a 3.5 mm plug on it. This particular unit is in very good shape both electrically and cosmetically. I can not find a scratch, dent, or ding on it. Electrically, it works as it should. Buy this unit with manual for $125. . Yaesu NC-9 B Charger 13 V DC at 45 ma, 2.5 mm plug; $12 . Original Yaesu Manuals: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH-1B A2B speaker microphone, $2 SP-101 P, Speaker / Phone patch, $5 VX-1 dual band HT, $10 These are original Yaesu operating manuals only, in very nice condition. SPECIAL: Buy two, three, or four and take 10% off. Buy five or more and take 20% off. . I also have many other accessories available such as many different types of microphones, HTs, VHF and UHF rigs, HF and VHF/UHF antennas, connectors, miscellaneous accessories, etc. Just too many to list here. Please e-mail your requests. . Prices do not include shipping from Florida. Thanks. 73, Ken, W8EK Ken Simpson E-mail to W8EK@... or W8EK@... Voice Phone (352) 732-8400 .

I tried using the Yaesu web form on their website and they don't seem understand that setting up a web form means you should monitor it frequently. This evening I gave it another try and also emailed them using the email link on their website as well as called them. I had to leave a message because they were too busy to answer. Is there an independent parts dealer who is more responsive to customer needs, or do I just need to keep trying until I get through? Thanks!!! Donald KX8K

Hi. I've searched 开云体育 for a user group for the FTDX101mp or (FTDX101D) - but can't find one. Can someone please point me in the right direction on 开云体育 or elsewhere? Thanks 73, Brian K8GRR

Hi, connection was no problem. But can't configure in FlRig/FLDigi - has no Rif File (XML) Tried FT-817/817nd/FT2000 .. no success Which Baudrate (I prefere 4800 not/less sensible for Error)s Somewhere runns ? TNX for help Erich

Selling is allowed in this group for ham radio equipment only, and at least one of the items for sale must be related to the purpose of the group. We require that anything being sold here have a price with it. So "make offer" or anything like that will not be an acceptable post here. Please indicate if shipping is included, otherwise leave it out. Also, please indicate the general location of the equipment for sale, so others will know if it’s within driving distance for them, and if you're willing to meet someone X miles away from that location. If you have any information about the item, please add it, as it will make it more likely that it will sell. Just list similar to the following. This was a suggestion for the SWAN-AMATEUR-RADIO group. Just replace the Swan item with one that would fit the purpose of this group: Swan 350D, great cosmetic condition, may need new final tubes since output drops somewhat on 15 and 10 meters. Model 117XC AC power supply included. Asking $325.00 OBO. Located near Charlotte, NC. Will drive up to 25 miles from Charlotte for pickup or delivery. Call 444-444-4444, or email hamoperator@....

Has anyone successfully got the rigpi/ftdx5000mp to operate over the internet ? Also need to control 2 g1000 rotors. Any info will be help full . K0BBB duane

I wonder if any of you Yaesu exerts know of a work around for the usually very expensive AM filter in the FT107m. Drake had a resistor across the filter pins as a cheap workaround. Thanks, Marc-k7wxk

I have a recently acquired FT-107m that works amazingly well, except the power out on 80m is a bit low. All other bands are 100w or better (10m slightly less). All tested into a 50 ohm dummy load. My questions are: What is the likely cause of this, and is there an adjustment for this? My experience is limited with SS gear, so I am not as up to snuff on it as I am with vacuum tube gear. I have the service manual. Any suggestions would be greatly appreciated. Thanks, Marc-k7wxk

Yaesu HF Transceiver, Power Supply, DTMF Hand Microphone, and more For Sale: . Yaesu FT-840 HF Transceiver: The compact Yaesu FT-840 has two direct digital synthesizers and rotary encoder that provide silky-smooth tuning. The excellent general coverage receiver tunes .1-30 MHz in 10 Hz steps. The FT-840 uses a die-cast RF power amp with thermally switched fan to ensure up to 100 watts output. Other features include backlit 10 Hz LCD, IF shift, reverse CW, dual VFOs, 100 memories, attenuator, noise blanker, meter, scan modes, automatic antenna tuner, and speech processor. 9.5 x 3.7 x 7 inches. Requires 13 VDC at 20 Amps. Features: 0.1-30 MHz Receive 100 Memories LCD Display IF Shift Noise Blanker Adjustable RF Power 100 Watts Output Automatic Antenna Tuner Attenuator Dual VFO's Squelch This particular unit works like it should. Cosmetically, it is exceptionally good. It has one scratch that you can see if the light is just right. With paper work for $425. . Kenwood PS-430 Power Supply: I know it is not Yaesu, but it works great with the Yaesu FT-840 above. It is direct "Plug and Play" with the FT-840. The Kenwood PS-430 power supply provides 13.8 VDC at 20 Amps intermittent. Ripple voltage is less than 20 mV at 13.8 VDC and 15 A. Input is 120/220/240 VAC. This is a linear power supply, so no need to worry about noise from a switching supply. The rear panel has a hardwired Kenwood power cable (6 pin molex connector) to connect directly to the TS-120/130/140/430/440/450 and others. Actually it will work fine with any rig that uses the 6 pin molex plug, including Icom and Yaesu and others. There are also "plus" and "minus" terminal outputs (10 Amps max) on the back, useful for a VHf/UHF rig. A snap-down tilt bail is on the bottom panel to increase the operating angle. 6.8 x 3.75 x 9.675 inches 15.4 lbs. This one works like it should, with great output. With paper work for $100 . Yaesu MH-48 DTMF TouchTone Microphone 16 digit DTMF Pad Up/down switches on top Modular RJ-45 connector Like new $40 . Original Yaesu Manuals: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH-1B A2B speaker microphone, $2 SP-101 P, Speaker / Phone patch, $5 VX-1 dual band HT, $10 These are original Yaesu operating manuals only, in very nice condition. . I also have many other accessories available such as many different types of microphones, HTs, VHF and UHF rigs, HF and VHF/UHF antennas, connectors, miscellaneous accessories, etc. Just too many to list here. Please e-mail your requests. . Prices do not include shipping from Florida. Thanks. 73, Ken, W8EK Ken Simpson E-mail to W8EK@... or W8EK@... Voice Phone (352) 732-8400 .

Does anyone know the wiring scheme for the Yaesu FT107 dummy plug? This is the plug that is inserted in the DC power socket when the AC supply is to be used. I couldn't find anything online with reference to it. Tnx, Marc-k7wxk

Hi vy nice in RIGS FT-857 / 897 the CW Tuning LED (goes to blue if QRG matches) I enjoi this really. This I am vy missing in FT-818 Now sometimes use the Wolfwave or a DIY Audio Filter - but then you have to parts to handle... Any forcast for an update from Yaesu ? TNX Erich

Yaesu HF Transceiver, Desk Microphone, and Power Supply For Sale: . Yaesu FT-840 HF Transceiver: The compact Yaesu FT-840 has two direct digital synthesizers and rotary encoder that provide silky-smooth tuning. The excellent general coverage receiver tunes .1-30 MHz in 10 Hz steps. The FT-840 uses a die-cast RF power amp with thermally switched fan to ensure up to 100 watts output. Other features include backlit 10 Hz LCD, IF shift, reverse CW, dual VFOs, 100 memories, attenuator, noise blanker, meter, scan modes, automatic antenna tuner, and speech processor. 9.5 x 3.7 x 7 inches. Requires 13 VDC at 20 Amps. Features: 0.1-30 MHz Receive 100 Memories LCD Display IF Shift Noise Blanker Adjustable RF Power 100 Watts Output Automatic Antenna Tuner Attenuator Dual VFO's Squelch This particular unit works like it should. Cosmetically, it is exceptionally good. It has one scratch that you can see if the light is just right. With paper work for $425. . Yaesu YM-38 Deluxe Desk Microphone: The Yaesu YM-38 is a deluxe goose neck type desk microphone. But it is more than most microphones. The PTT switch also has a locking position. It has Up, Down, and F/S switches. It can be used on most any rig since it has a switch for 50 K (high) impedance, or 500 ohm (low) impedance. This one presently has a round 8 pin connector, obviously wired for Yaesu, which makes it usable on TenTec as well as other rigs. This one has the mic element replaced with a Heil HC-5, which is Heil's mic element with extra "punch" for working DX. This particular unit looks like new cosmetically, with no scratches or defects. It also works perfectly. Buy it with paper work for only $120 . Kenwood PS-430 Power Supply: I know it is not Yaesu, but it works great with the Yaesu FT-840 above. The Kenwood PS-430 power supply provides 13.8 VDC at 20 Amps intermittent. Ripple voltage is less than 20 mV at 13.8 VDC and 15 A. Input is 120/220/240 VAC. This is a linear power supply, so no need to worry about noise from a switching supply. The rear panel has a hardwired Kenwood power cable (6 pin molex connector) to connect directly to the TS-120/130/140/430/440/450 and others. Actually it will work fine with any rig that uses the 6 pin molex plug, including Icom and Yaesu and others. There are also "plus" and "minus" terminal outputs (10 Amps max) on the back, useful for a VHf/UHF rig. A snap-down tilt bail is on the bottom panel to increase the operating angle. 6.8 x 3.75 x 9.675 inches 15.4 lbs. This one works like it should, with great output. Cosmetically it is average. Not exceptional like most of the gear I sell. With paper work for $100 . Original Yaesu Manuals: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH-1B A2B speaker microphone, $2 SP-101 P, Speaker / Phone patch, $5 VX-1 dual band HT, $10 These are original Yaesu operating manuals only, in very nice condition. . I also have many other accessories available such as many different types of microphones, HTs, VHF and UHF rigs, HF and VHF/UHF antennas, connectors, miscellaneous accessories, etc. Just too many to list here. Please e-mail your requests. . Prices do not include shipping from Florida. Thanks. 73, Ken, W8EK Ken Simpson E-mail to W8EK@... or W8EK@... Voice Phone (352) 732-8400 .

someone know what the type /size of the batteries in the fnb31 38, etc are ?? the john dutton46@...

Two Yaesu HF Transceivers For Sale: . Yaesu FT-767GX HF rig: The Yaesu FT-767GX is a 100 watt top of the line HF transceiver covering 160-10 meters plus 100 kHz to 30000 kHz. It even includes a built in HF antenna tuner. Other advanced features include IF shift, Notch, Electronic Keyer, Squelch, QSK, dual VFOs, Noise Blanker, Attenuator, Passband Tuning and memories. It has an internal AC power supply. The FT-767GX is designed to accept optional band modules for coverage of 6 meters, 2 meters and 70 cm. Features: 160-10 meters Automatic Antenna Tuner IF Notch IF Shift Dual VFOs Noise Blanker Semi/Full Break-in CW Attenuator Speech Compressor VOX Electronic Keyer This one works like it should. It has had the antenna tuner battery replaced, and has the main backup battery brought out so it can easily be changed. Cosmetically, it is exceptional. These sold new for over $1200. Buy this one with manual for only $550. . Yaesu FT-840 HF Transceiver: The compact Yaesu FT-840 has two direct digital synthesizers and rotary encoder that provide silky-smooth tuning. The excellent general coverage receiver tunes .1-30 MHz in 10 Hz steps. The FT-840 uses a die-cast RF power amp with thermally switched fan to ensure up to 100 watts output. Other features include backlit 10 Hz LCD, IF shift, reverse CW, dual VFOs, 100 memories, attenuator, noise blanker, meter, scan modes and speech processor. 9.5 x 3.7 x 7 inches. Requires 13 VDC at 20 Amps. Features: 0.1-30 MHz Receive 100 Memories LCD Display IF Shift Noise Blanker Adjustable RF Power 100 Watts Output Attenuator Dual VFO's Squelch This particular unit works like it should. Cosmetically, it is exceptionally good. It has one scratch that you can see if the light is just right. With paper work for $425. . Original Yaesu Manuals: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH-1B A2B speaker microphone, $2 SP-101 P, Speaker / Phone patch, $5 VX-1 dual band HT, $10 These are original Yaesu operating manuals only, in very nice condition. . I also have many other accessories available such as many different types of microphones, HTs, VHF and UHF rigs, HF and VHF/UHF antennas, connectors, miscellaneous accessories, etc. Just too many to list here. Please e-mail your requests. . Prices do not include shipping from Florida. Thanks. 73, Ken, W8EK Ken Simpson E-mail to W8EK@... or W8EK@... Voice Phone (352) 732-8400 .

Yaesu HF Transceiver, 2 m Transceiver, Power Supply, Mic, and more For Sale: . Yaesu FT-840 HF Transceiver For Sale: The compact Yaesu FT-840 has two direct digital synthesizers and rotary encoder that provide silky-smooth tuning. The excellent general coverage receiver tunes .1-30 MHz in 10 Hz steps. The FT-840 uses a die-cast RF power amp with thermally switched fan to ensure up to 100 watts output. Other features include backlit 10 Hz LCD, IF shift, reverse CW, dual VFOs, 100 memories, attenuator, noise blanker, meter, scan modes and speech processor. 9.5 x 3.7 x 7 inches. Requires 13 VDC at 20 Amps. Features: 0.1-30 MHz Receive 100 Memories LCD Display IF Shift Noise Blanker Adjustable RF Power 100 Watts Output Attenuator Dual VFO's Squelch This particular unit works like it should. Cosmetically, it is exceptionally good. It has one scratch that you can see if the light is just right. With paper work for $425 . Yaesu FT-1802 M, 2 m Transceiver: The FT-1802 M features outstanding audio on both transmit and receive. It has strong receiver performance, covering 136 to 174 MHz, and boasts 221 memories. There is also a 10 channel NOAA weather bank. CTCSS and DCS Encoder and Decoder circuits. It even has a unique CW trainer to practice Morse Code, all in a rugged die cast chassis. The supplied MH-48A6J DTMF hand mic includes four programmable keys. Features: 221 Memories 8 Memory Banks 50/25/10/5 Watts Output APO - Automatic Power-Off ARS - Automatic Repeater Shift Busy Channel Lock-Out DTMF Memories CTCSS Encode/Decode CW Trainer Password Function Backlit DTMF Mic This particular unit works 100% and looks like new. In fact it is still in its original box, with all its "stuff". I was told it had been won at a hamfest, and never used. With mic, mobile bracket, power cord, other misc. and manual in original box for $125 . Rig Programming Software/hardware: These days the rigs have so many memories plus other features, that it is almost impossible to program them manually. This software takes care of this problem, by letting you use the computer to program. ADMS-1802 for Yaesu FT-1802 (see above) and maybe others The ADMS-1802 consists of a hardware cable, plus a software CD, plus instructions to program a Yaesu FT-1802, and possibly other rigs. This unit appears that it might be new. $25 . Yaesu FP-707, 20 Amp Power Supply: The Yaesu FP-707 power supply is designed to match the FT-707 transceiver, but will also match the FT-747 and 757 series transceivers, or any HF transceiver that uses a 4 pin Cinch- Jones connector. Although it has the 4 pin connector, it also has a set of binding posts on the back, so it can be used with any rig requiring up to 20 amps. This is a linear power supply, so no switching noise. It also has a built in speaker. This one works great. It looks really terrific, especially considering its age. With paper work for only $100. . Yaesu Hand Microphone: Yaesu MH-48 DTMF Hand Microphone For Yaesu FT-7800R/7900R/1807M/1802M/1900 Has 16 digit DTMF TouchTone pad, plus 4 extra programmable buttons, plus Up/Down and PTT. Also had backlight with switch. Modular connector. Real Yaesu and not Chinese clone. It works fine and appears to be unused. $40 . Original Yaesu Manuals For Sale: These are the manuals only. All are originals, and not copies. Most are in close to new condition. FNB-9,10,11,12 Battery packs, $2 FC-757AT Antenna Tuner, $10 FT-100 HF/VHF Transceiver, $18 FT-470 Dual Band HT, $10 FT-757 GX, HF Transceiver, $18 FT-720 R, 2 meter mobile, $8 FT-1802 M, 2 meter mobile, $12 FT-2700 Dual Band Xcvr, $12 FTH-2005 HT, $5 FTS-8 tone squelch unit, $3 FTS-12 tone squelch unit, $3 MH-1B A2B speaker microphone, $2 SP-101 P, Speaker / Phone patch, $5 VX-1 dual band HT, $10 These are original Yaesu operating manuals only, in very nice condition. Service Manuals: Maintenance Service Manual for Yaesu FT-208 R 2 meter HT. Looks new. $25 Technical Supplement for Yaesu FT-2700 Dual Band Mobile. Looks new. $20 . I also have many other accessories available such as many different types of microphones, HTs, VHF and UHF

Yaesu HF Transceiver, 2 m Transceiver, TenTec Desk Mic (also fits Yaesu), Filter, Power Supply and more For Sale: . Yaesu FT-840 HF Transceiver For Sale: The compact Yaesu FT-840 has two direct digital synthesizers and rotary encoder that provide silky-smooth tuning. The excellent general coverage receiver tunes .1-30 MHz in 10 Hz steps. The FT-840 uses a die-cast RF power amp with thermally switched fan to ensure up to 100 watts output. Other features include backlit 10 Hz LCD, IF shift, reverse CW, dual VFOs, 100 memories, attenuator, noise blanker, meter, scan modes and speech processor. 9.5 x 3.7 x 7 inches. Requires 13 VDC at 20 Amps. Features: 0.1-30 MHz Receive 100 Memories LCD Display IF Shift Noise Blanker Adjustable RF Power 100 Watts Output Attenuator Dual VFO's Squelch This particular unit works like it should. Cosmetically, it is exceptionally good. It has one scratch that you can see if the light is just right. With paper work for $425 . TenTec 708 A Desk Microphone: Note that this microphone also fits Yaesu and plugs into Yaesu rigs, and needs no modifications. The 708 A deluxe base microphone is an Omni- directional dynamic microphones designed for use as a communications station microphone for Amateur Radio and other transmitting applications. It has a round 8 pin connector and can be used without modification for many Yaesu Transceivers in addition to TenTec transceivers. The unit consists of a metal die-cast base with 3 position PTT switch, flexible metal goose neck, dynamic microphone element and ball-type element housing. It has tailored frequency response from 30 Hz to 12 kHz designed for excellent transmit audio in SSB, AM, and FM modes. This one one looks like new. No defects of any sort. Electrically, it works as it should. With paper work for only $90. . Yaesu FT-1802 M, 2 m Transceiver: The FT-1802 M features outstanding audio on both transmit and receive. It has strong receiver performance, covering 136 to 174 MHz, and boasts 221 memories. There is also a 10 channel NOAA weather bank. CTCSS and DCS Encoder and Decoder circuits. It even has a unique CW trainer to practice Morse Code, all in a rugged die cast chassis. The supplied MH-48A6J DTMF hand mic includes four programmable keys. Features: 221 Memories 8 Memory Banks 50/25/10/5 Watts Output APO - Automatic Power-Off ARS - Automatic Repeater Shift Busy Channel Lock-Out DTMF Memories CTCSS Encode/Decode CW Trainer Password Function Backlit DTMF Mic This particular unit works 100% and looks like new. In fact it is still in its original box, with all its "stuff". I was told it had been won at a hamfest, and never used. With mic, mobile bracket, power cord, other misc. and manual in original box for $125 . Rig Programming Software/hardware: These days the rigs have so many memories plus other features, that it is almost impossible to program them manually. This software takes care of this problem, by letting you use the computer to program. ADMS-1802 for Yaesu FT-1802 (see above) and maybe others The ADMS-1802 consists of a hardware cable, plus a software CD, plus instructions to program a Yaesu FT-1802, and possibly other rigs. This unit appears that it might be new. $25 . Collins Mechanical Filter for Yaesu: This Collins Mechanical filter also has Yaesu numbers and was designed to be used in Yaesu Transceivers. Please check you manual to see if it fits your rig. It is designed for the 455 KHz IF. If your Yaesu rig uses 455 KHz filters, it probably fits. It fits the FT-817, FT-818, FT-847, FT-857, FT-897, FT-2000 and probably others. Most of you may know that Collins no longer makes mechanical filters. This one works as it should, and looks like new. Yaesu XF-119 SN (YF-122 SN) Collins 526-8739-010 2300 Hz, designed for narrow SSB $135 . Yaesu FP-707, 20 Amp Power Supply: The Yaesu FP-707 power supply is designed to match the FT-707 transceiver, but will also match the FT-747 and 757 series transceivers, or any HF transceiver that uses a 4 pin Cinch- Jones connector. Although it has the 4 pin connector, it also has a set of binding posts on th