开云体育

ctrl + shift + ? for shortcuts
© 2025 开云体育
  1. YaMoRC-Digikeijs
  2. Messages
Messages Topics Expanded Polls
Date
Re: What determines the power on position of my turnouts?
Karst, I am glad I asked. I would never have found that option to set the default aspect to 16 which is where all of the turnouts show N aspect. I tried it on one of the YD8116 modules and it
By Oldngrey · #4847 ·
Re: NCE EB1 Circuit Breaker - is anyone using these with a YD7001 and DR5033 boosters ?
By Dennis Cherry · #4846 ·
Re: NCE EB1 Circuit Breaker - is anyone using these with a YD7001 and DR5033 boosters ?
Hi I have an update on this topic.? The simple answer is the NCE EB1s will not work with Digikeijs command stations and boosters, and will most likely not work with the follow-on products from
By Jay Lennox · #4845 ·
Re: What determines the power on position of my turnouts?
Basically "Aspect 0" but... there is an Update in Build 72 and higher that.... ... has the "No Initialization" flag. Checking it, prevents the output to be switched to "default" on power-on. From
By karst.drenth · #4844 ·
What determines the power on position of my turnouts?
I have a couple of YD8116 switching decoders connected to 22 Tortoise switch machines via YD6940 3 to 2 wire adapters. At power on nearly all turnouts go to R (reverse) position even though when the
By Oldngrey · #4843 ·
Re: Increasing the DR5033 Short Circuit Delay to 300ms - what problems could happen ?
It sounds like it's time to drag out an oscilloscope and find out for sure what's happening.
By Ray Jorgenson · #4842 ·
Re: Increasing the DR5033 Short Circuit Delay to 300ms - what problems could happen ?
Jay, I am using PSX and PSXX breakers from DCC Specialties. https://dccspecialties.wpengine.com/wp-content/uploads/2023/09/PSXX-Manual-Rev-C-Rev-G.pdf I believe that these are set up with the
By Bob Gamble · #4841 ·
Re: Increasing the DR5033 Short Circuit Delay to 300ms - what problems could happen ?
Karst and Bob Thank you for your feedback on my question. First, Bob could you share what brand circuit breakers you are using and how you have them setup (jumpers, CV settings, etc.)? ?We have
By Jay Lennox · #4840 ·
Re: Increasing the DR5033 Short Circuit Delay to 300ms - what problems could happen ?
*Am I right, that the sole supply to that breaker is the Track-Out power from the booster ? * Yes, this would be the correct way. I have three DR5033 and seven breakers. They work fine as long as
By Bob Gamble · #4839 ·
Re: Increasing the DR5033 Short Circuit Delay to 300ms - what problems could happen ?
By the way, that it is *IS* possible to get a correct "breaker-operation" is proven by our YD7432 reverse loop controller ?
By karst.drenth · #4838 ·
Re: Increasing the DR5033 Short Circuit Delay to 300ms - what problems could happen ?
Ok, Thanks for the explanation Bob.? So it *IS* symptom curing ( minimizing the effect of human error ?) Am I right, that the sole supply to that breaker is the Track-Out power from the booster
By karst.drenth · #4837 ·
Re: Increasing the DR5033 Short Circuit Delay to 300ms - what problems could happen ?
Karst, * Note: I simply cannot understand why one would install such breakers. The YD and DR power devices really are fast enough to adequately turn off the power in case of a short. * Typically it
By Bob Gamble · #4836 ·
Re: Increasing the DR5033 Short Circuit Delay to 300ms - what problems could happen ?
Well... first I think one should solve the cause, not the symptom. Obviously the cause is that that ominous circuitbreaker does not come after it's specs... ;) Almost... the 5033 will detect
By karst.drenth · #4835 ·
Re: Increasing the DR5033 Short Circuit Delay to 300ms - what problems could happen ?
Hmmmmmm, I have never needed to vary this setting, but, I think the issues could be:- Killing the item that caused the short - But it's already faulty so why worry. Stressing the semiconductors
By Pete S. · #4834 ·
Increasing the DR5033 Short Circuit Delay to 300ms - what problems could happen ?
Hi I am wondering if anyone has any experience with increasing the short circuit delay on the DR5033 from 96ms (default) to 300ms or more ? This is LocoNet CV 13 that is being increased on the
By Jay Lennox · #4833 ·
Re: NCE EB1 Circuit Breaker - is anyone using these with a YD7001 and DR5033 boosters ?
It could be you're experiencing 'switch bounce'; no switches close in one clean motion, but instead bounce open & closed multiple times in a multiple msec or tens of msec interval before staying
By Ray Jorgenson · #4832 ·
Re: NCE EB1 Circuit Breaker - is anyone using these with a YD7001 and DR5033 boosters ?
Stuart The trip time on the EB1 is controlled by CV130.? I have set CV130=1, which should give a 16 ms trip time.? In theory CV130 =1 when shipped from NCE - I purposely set it to make sure it was
By Jay Lennox · #4831 ·
Re: NCE EB1 Circuit Breaker - is anyone using these with a YD7001 and DR5033 boosters ?
I use a couple of NCE EB1 with my Z21 in the accessory bus and only changed the current trip to 2.5A to ensure the EB1 trips before the Z21 or the booster. I wonder if you have reduced the current
By Iain Morrison · #4830 ·
Re: NCE EB1 Circuit Breaker - is anyone using these with a YD7001 and DR5033 boosters ?
Jay, I have not used this combination before, but I have a couple of thoughts. What have you set the trip time on the NCE EB1 circuit breaker? I think the minimum setting is ~10ms. Can you try the
By Stuart Baker · #4829 ·
NCE EB1 Circuit Breaker - is anyone using these with a YD7001 and DR5033 boosters ?
Hi My club, York Railway Modellers, purchased several NCE EB1 circuit breakers and we cannot get them working with our YD7001s and the DR5033 boosters without increasing the circuit breaker trip time
By Jay Lennox · #4828 ·
1 - 20 of 4740