开云体育

ctrl + shift + ? for shortcuts
© 2025 开云体育
Re: Railcom with JMRI Reporters working on TCS CS-105 through Digikeijs DR5088RC
Whoopee.. Personally looking at 5 units to go with my 2 Digikeijs DR5088RC units...
By Tank · #4766 ·
Re: Railcom with JMRI Reporters working on TCS CS-105 through Digikeijs DR5088RC
Looking forward, need one to complete my block detection. The DR5088RC will still be used, it is working flawlessly with the bias resistors I posted earlier on the forum. Dennis Cherry
By Dennis Cherry · #4765 ·
Re: Railcom with JMRI Reporters working on TCS CS-105 through Digikeijs DR5088RC
Won‘t take long anymore. Dev. is ready, waiting for a production slot ;) (YD6016LN-RC) greets, Karst
By karst.drenth · #4764 ·
Railcom with JMRI Reporters working on TCS CS-105 through Digikeijs DR5088RC
I was discussing RailCom and the CS-105 earlier. ?I had not seen anyone post about getting RailCom to work with JMRI Reporters through the Digikeijs DR5088RC and a RR-Circuits LCC-LocoNet Gateway on
Re: DR4088LN-CS with DR4088CS some of my sensed blocks activate with just a touch of the sensed wire
I started another thread for the double tap wheel gap activation issue. It was solved by changing the default sensor delay in JMRI. As far as I know you cannot change any detection setting related to
By Mike's DeepRun RR · #4762 ·
Re: DR4088LN-CS with DR4088CS trailing blocks turn on and off when metal wheels pass over insulated jointer
Iain Thank you for your response. As you indicated there is no where that I have found to add a delay to prevent these nuisance detections. I am using JMRI so I went to the sensor table/defaults/
By Mike's DeepRun RR · #4761 ·
Re: DR4088LN-CS with DR4088CS trailing blocks turn on and off when metal wheels pass over insulated jointer
In software other than JMRI (or feedbacks other than DR4088xx) this ‘bouncing’ can be cured by increasing the feedback switch-on delay slightly, from 0ms to 25ms, or even 50ms. This creates enough
By Iain Morrison · #4760 ·
DR4088LN-CS with DR4088CS trailing blocks turn on and off when metal wheels pass over insulated jointer
Thanks in advance. When running a train with multiple cars and a single engine the first block activate as expected when the engine enters it but then when the trailing cars with metal wheels cross
By Mike's DeepRun RR · #4759 ·
Re: YD8008 with YD6940 and Kato Unitrack turnouts
Karst Thanks for this advice I'll upgrade my PSU. Before reading your post I'd actually come to a similar conclusion that it was a power supply issue. I was originally powering two YD8116s together
By grahammjmason · #4758 ·
Re: YD8008 with YD6940 and Kato Unitrack turnouts
There lies your problem, our experience is, that the Kato's connected to the YD8008/6940 combo need 15V PSU of about 400mA minimum. Reason: Both YD8008 (1.2V) and YD6940 (0.7) introduce a voltage
By karst.drenth · #4757 ·
Re: DR4088LN-CS with DR4088CS some of my sensed blocks activate with just a touch of the sensed wire
I discovered tonight a wiring booboo. When I switched to tortoise switch machines I powered some of the frogs with straight booster power. So when the engine goes over the frog the power is not sensed
By Mike's DeepRun RR · #4756 ·
Re: YD8008 with YD6940 and Kato Unitrack turnouts
Iain I took my advice from the YaMoRC website.? It clearly states that for Kato points you need to use the YD8008 with the YD6940 to convert to 2 wire from 3 wire.? I had originally thought about
By grahammjmason · #4755 ·
Re: YD8008 with YD6940 and Kato Unitrack turnouts
Graham, I wonder if the YD8008 are the correct switches to be using with Kato turnouts. The common use for the YD8008 is power hungry solenoids such as the Peco/Seep style that need a real thump
By Iain Morrison · #4754 ·
YD8008 with YD6940 and Kato Unitrack turnouts
I'm having problems with the reliability when using this combination with iTrain. They occur mostly in automatic mode but do also? when manually operating individual turnouts or when using the track
By grahammjmason · #4753 ·
DR4088LN-CS with DR4088CS some of my sensed blocks activate with just a touch of the sensed wire
I have just discovered after adding additional blocks that some of the track when just the sensed rail is touched with my finger it will activate the sensor and generate the message of an active
By Mike's DeepRun RR · #4752 ·
Re: YD6016LN-RC
Fingers crossed that it is soon ?
By Iain Morrison · #4751 ·
YD6016LN-RC
Hello, Is there any information when this Railcom detector module will be released? Thanks
By Tank · #4750 ·
Re: DCC EXT DR4018?
You need a YD8116 Sent: 24 January 2025 08:34 To: [email protected] Subject: DCC EXT DR4018? I have a YD7001 that I believe supports DCCExt. Can I use DCCExt with a DR4018 or do I
By Iain Morrison · #4749 ·
DCC EXT DR4018?
I have a YD7001 that I believe supports DCCExt. Can I use DCCExt with a DR4018 or do I need a ?YD8116? I use ITrain which also supports DCCExt. Roger
By rog.pearson@... · #4748 ·
Re: DR5000 & Cobalt Problems
well well well looks like i have the same problem with the adsx2 loosing addresses if I use a sprogg3 the problem disapears
By Alan Watt · #4747 ·