Welcome to the YaMoRC/Digikeijs English Forum
?
This Table of contents provides information about the YaMoRC and Digikeijs products in US English and JMRI.
Click on the "Read More" to see all the information.
Legal notice:
All instructions are written to the best of our knowledge and belief of the respective authors.
Nevertheless, no liability for any errors or omission in the Documentation is intentional!
?
General:
The Main website of the manufacturers YaMoRC and Digikeijs can be reached via the following link:
- Link to the
- YaMoRC Support for Documents. TBD
- Link to the Digikeijs Firmware:?The latest firmware for each product will be in its respect file directory if we have the latest firmware.
- This is an archive that was made and will have documents in other languages. Check before you download.
?
US Dealers:
- for YaMoRC and Digikeijs Products.
Click on any RED Model number below, it will send you to the files page for that device.
English Only Manuals and Photos, etc can be found on this Forum and elsewhere:
Central Station:
- DR5000 The first Command Station with all conceivable connection sockets and LED status lights, USB, LAN & WLAN
- Detailed Tutorial - Rudy's Model Railway Videos on DR5000
Booster:
- DR5033 3 amp Booster works with many different Command Stations
Switch and Servo Modules:
- DK50018 16 Channel Bluetooth accessory and switching decoder
- DR4018 16 Channel Multi-Protocol Switching Decoder
- Manual: DR4018 Advanced V1.2
- Video Series for the DR4018 or DK50018 on Preset 1 in JMRI to invert the outputs for LED Signals.
-
- Guide for Testing the DR4018/DK50018 for proper Preset Configuration.?
- DR4024 4-output multi-protocol servo decoder with 4 additional switching outputs
?
Feedback Modules:
- ?DR4088CS & CS-GND 16-input feedback module (S88)
?
- ?DR4088LN-CS, LN-GND & LN-OPTO 16-input feedback module (LocoNet)
-
?
- ?DR4088RB-CS & RB-OPTO 16-input feedback module (R-Bus)
?
- ?DR5088RC 16-input feedback module with RailCom (LocoNet)
?
Reverse Loop Module
- ? DR5013
- Video :?
Turntable Module
- ??? DR5052
?
Other Equipment
- ??? DR4050 DigiLEDs RGB Model Train Light Control
?
- ??? DR5022 DigiControl for the control of 2 trains via a swivel
?
- ??? DR5039 LocoNet-B to CDE
?
- ??? DR5097 DigiNetHub 10x LocoNet Hub
?
- ??? DR5098 DigiNetHub 10x X-Bus Hub
?
- ??? DR5099 DigiNetHub 5x X-Bus Hub & 5x LocoNet Hub
Software
- JMRI
?
- RocRail
-
- ITrain
- Train Controller
- Perecli RRA (Railroad Automation)
- ?
- ?
- ?
- ?
- ?
-
- AnyRail:
Throttles:
- Document showing the Apps that work with JMRI and DR5000 with download links.
- Roco WLANmaus Throttle Setup For The Digikeijs DR5000
- Test of the Proto-Throttle with the Digikeijs DR5000
- RtDrive Lenz With The Digikeijs DR5000
- ESU Mobile Control II Throttle With The Digikeijs DR5000
- DigiTrainsPro (Android Phone) DR5000 Setup (Now a monthly fee of 5 Eros for this version)
- Z21 App for Apple or Android Phones.?
?
Other Features:
- ?
?
?
?
|
Re: New file uploaded to [email protected]
Glad I could help
Andy
By
andrew whitaker
·
#44
·
|
|
Re: New file uploaded to [email protected]
Hi Andy
Just to report back that your advice has proved successful! The first PL11 was moved just enough to ease the control bar and it now works flawlessly. Investigation of the second PL11 showed
By
Chris Youlden
·
#43
·
|
|
Re: New file uploaded to [email protected]
Thanks for that, Andy. I have stuck them down but will reposition them. It helps to know they can be driven by the 4018s.Many thanksChrisSent from Samsung tablet.
By
Chris Youlden
·
#42
·
|
|
Re: New file uploaded to [email protected]
Chris, your correct, I have the manual file now from Digikeijs and starting to correct and update the manual.? If anyone knows technical errors that need to be fixed let me know.
I am correcting
By
Dennis Cherry
·
#41
·
Edited
|
|
Re: New file uploaded to [email protected]
Also depends on the power supply you are using - if you are having issues might be worth putting a more powerful separate power supply into DR4018 rather than using DCC Bus
Iain Morrison
07767
By
Iain Morrison
·
#40
·
|
|
Re: New file uploaded to [email protected]
Hi Chris,
Have you adjusted the position of the motors? I have just fitted 14 pl11s to a couple of dr4018s and found that I had to move a few of them into or away from the points lever because the
By
andrew whitaker
·
#39
·
|
|
Re: New file uploaded to [email protected]
Does anyone find the DR4018 hasn't the oomph to switch Peco PL-11 side-mounted turnout motors?
If so, can anything be done to improve this, such as lengthening the duration of the switch pulse?
--
By
Chris Youlden
·
#38
·
|
|
Re: New file uploaded to [email protected]
Reading this topic and the implication that you need to read both a new and old data sheets for the DR4018 is this also true for other products?
If so, where does one find older datasheets on the
By
Colin Bennett
·
#37
·
|
|
Re: New file uploaded to [email protected]
There may a problem then as the one on the Digikeijs website (modified 08/04/2019 but dated 23/12/18) has more information contained within it that the one you have uploaded.
You actually need to
By
Iain Morrison
·
#36
·
|
|
Re: New file uploaded to [email protected]
No, this is an earlier version (V1.2) dated? 05-02-2012.? It has some information not in the most current version Dated 12-23-2018)
There is some of the programming steps not found in the current
By
Dennis Cherry
·
#35
·
Edited
|
|
Re: New file uploaded to [email protected]
I think that this is the new DR4018 manual that was released on the Digikeijs website a few weeks ago?
Sent: 16 April 2019 15:58
To: [email protected]
Subject: [Digikeijs], JMRI, Rocrail,
By
Iain Morrison
·
#34
·
|
|
New file uploaded to [email protected]
Hello,
This email message is a notification to let you know that a file has been uploaded to the Files area of the [email protected] group.
*File:* 20933457-07f432-DR4018_V1.2.pdf
*Uploaded By:*
By
[email protected] Notification <Digikeijs+notification@...>
·
#33
·
|
|
Re: DR5000 & 6pin decoders
Thanks James,
it was that, strange as I’d only ran a 101 with that as it’s address the day before and the last short loco address was blank when I opened it tonight, but 108 now
By
andrew whitaker
·
#32
·
|
|
Re: DR5000 which protocol?
Colin,
The DR5000 will terminate the LocoNet.? Both devices will need to be plugged into the LocoNet B for the RailSync.??
Ryan
By
Iron Planet Hobbies
·
#31
·
|
|
Re: DR5000 which protocol?
Sorry all, I should have typed RailSync not railcom!
Colin
By
Colin Bennett
·
#30
·
|
|
Re: DR5000 which protocol?
Hi Colin,
I don't know about your other questions, but BDL168 does not support
Railcom (BDL168 supports transponding which is different). If you want
Railcom you will need Digikeijs
By
Konrad Malkowski
·
#29
·
|
|
DR5000 which protocol?
I am currently using a Sprog 3 to control Locos and turnouts (CML DAC20) via JMRI.
?
If I wish to change my controller to a DR5000 and upgrade to block detection later Digitrax BDL168 I would like
By
Colin Bennett
·
#28
·
Edited
|
|
Re: DR5000 & 6pin decoders
Hello
?
I am wondering if you have for this page set right in the DR5000 Config.
This might be what’s wrong.
?
?
?
Many Thanks
?
James Hudson
DCC Train Automation
+441823
By
James
·
#27
·
Edited
|
|
Re: DR5000 & 6pin decoders
I would still try changing the address, and perhaps reset the chip before you start looking at other ideas
By
Iain Morrison
·
#26
·
|
|
Re: DR5000 & 6pin decoders
I have other locos with lower and higher addresses that work fine, I was wondering if 108 is blocked or if there’s a problem specific to either early bachmann chips or ESU lokpilots with that
By
andrew whitaker
·
#25
·
|