开云体育

ctrl + shift + ? for shortcuts
© 2025 开云体育
  1. YaMoRC-Digikeijs
  2. Messages
Expanded Topics Messages Polls
Date
Re: Detailed setup manual for the YD7010?

Rick Norell
 

Novice here.? So programming the decoder with DecoderPro totally completes the job?? I would not need to go through decoder programing in YD7010 or in the Z21 app?? If so, eliminates redundant entry and eases decoder programming for the more complex ESU sound decoders.? Thank you!
Re: YD7001 stuck in demo mode etc.

 

Hi John
?
I did that and it was not in there, thanks any way.
Just posted it back to dealer.
Re: YD7001 stuck in demo mode etc.

 

Did you check your junk folder.? I had a similar problem.? It turned out I got the code several times but it went into the junk folder and I failed to notice.? My bad but it fooled me for a few days.
Re: YD7001 stuck in demo mode etc.

 

I never received the activation code message despite requesting it, that may be the problem !
Re: YD7001 stuck in demo mode etc.

 

Reinstall the drivers by right clicking the installer, and selecting ‘Run as Administrator’.
Re: Detailed setup manual for the YD7010?

 

JMRI does do the actual programming, it only provides a pictorial and textual human interface to your command station. The command station - in your case a YD7010 still does the actual programming and control.


Many Thanks

Iain Morrison


On Thu, 19 Dec 2024 at 04:11, Rick Norell via <ricknorell=[email protected]> wrote:
Karst, thank you for the latest manual!? If I purchase, I will be a very basic user.? I have no legacy dcc equipment to consider.? I want walk around locomotive control using wifi and basic DCC? functions (stop, go, forward, reverse, consisting, and sound).? Turnouts are manual control with ground throws.? Should be easy with your system!? A quick start writeup would be fabulous with detailed explanations for novices like me!
?
Going through the manual, I believe I would need to make entries in the following sections:

? ? Lan? Basic settings??? (specify DHCP)

? ? ES link settings? ?NA, no modules

? ? Loconet sections? ?NA, no digitrax components

? ??Track out DCC properties track? (turn off railcom, accept defaults for remaining entries)

? ? Track out DCC properties locomotives (highest short address 99, speed levels ALL)

? ? Track out DCC slots NA no loconet

? ? Track out DCC switches?? NA? (use manual switches)

? ? XBus/RBus settings? NA

? ? BBus properties?? accept defaults???

? ? RB-Bus settings? NA??

? ? Program track CV programming? (both program track and POM, program decoders)

? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? redundant to program decoders on JMRI, Z21 and YD7010??

? ? Program track test drives (displayed on cell phone, commercial throttles?)

? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?dispatch only used for certain hand held controllers or all?

? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?which hand hold controllers do not have direct selection of locos?

? ?Program track settings? ? ? ?use defaults?? what do users say?? 750mA seems too high

? ?Wifi basic settings? ?use defaults

? ?Wifi expert settings? ????? unsure if a novice should make entries here
? ?USB update? ? use defaults?
? ?Track go/stop control? ? ?connection via home network, enter IP of my router, language english, no control panel
? ?Track go/stop settings? ? use default settings, should I care about loconet slots?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ??
? ?Infrared properties? ? ? NA
?
Did I select the right items for entry and appropriate values?
Any documentation on how to access Z21 and JMRI through the YD7010?
?
Thank you!
Rick
Re: Detailed setup manual for the YD7010?

Rick Norell
 

Karst, thank you for the latest manual!? If I purchase, I will be a very basic user.? I have no legacy dcc equipment to consider.? I want walk around locomotive control using wifi and basic DCC? functions (stop, go, forward, reverse, consisting, and sound).? Turnouts are manual control with ground throws.? Should be easy with your system!? A quick start writeup would be fabulous with detailed explanations for novices like me!
?
Going through the manual, I believe I would need to make entries in the following sections:

? ? Lan? Basic settings??? (specify DHCP)

? ? ES link settings? ?NA, no modules

? ? Loconet sections? ?NA, no digitrax components

? ??Track out DCC properties track? (turn off railcom, accept defaults for remaining entries)

? ? Track out DCC properties locomotives (highest short address 99, speed levels ALL)

? ? Track out DCC slots NA no loconet

? ? Track out DCC switches?? NA? (use manual switches)

? ? XBus/RBus settings? NA

? ? BBus properties?? accept defaults???

? ? RB-Bus settings? NA??

? ? Program track CV programming? (both program track and POM, program decoders)

? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? redundant to program decoders on JMRI, Z21 and YD7010??

? ? Program track test drives (displayed on cell phone, commercial throttles?)

? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?dispatch only used for certain hand held controllers or all?

? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?which hand hold controllers do not have direct selection of locos?

? ?Program track settings? ? ? ?use defaults?? what do users say?? 750mA seems too high

? ?Wifi basic settings? ?use defaults

? ?Wifi expert settings? ????? unsure if a novice should make entries here
? ?USB update? ? use defaults?
? ?Track go/stop control? ? ?connection via home network, enter IP of my router, language english, no control panel
? ?Track go/stop settings? ? use default settings, should I care about loconet slots?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ??
? ?Infrared properties? ? ? NA
?
Did I select the right items for entry and appropriate values?
Any documentation on how to access Z21 and JMRI through the YD7010?
?
Thank you!
Rick
Re: YD7001 | Resetting Command Station after Short

 

Glad to see you managed to RTFM.
?
Shorts. These are not "normal". My system runs very well without them...... If you are getting shorts for any reason, then you need to understand why and then take action to prevent them.
?
Reset. It's manual. This will encourage action to remove causes of shorts. To continually reset onto a short condition will stress things. Then they die.
?
Pete S
Re: YD7001 stuck in demo mode etc.

 

Hi Iain
I did that 4 times with 2 PCs same result, may have been a faulty YD9401.
Now given up on it and going back to my old Digitrax.
Re: YD7001 stuck in demo mode etc.

 

开云体育

It sounds very much like you do not have a connection from the PC to the YD7001.

?

I suggest that you re-install the YD7001 software on you PC and make sure you agree to all the drivers being installed.

?

From: [email protected] <[email protected]> On Behalf Of terry lee via groups.io
Sent: 18 December 2024 17:01
To: [email protected]
Subject: Re: YD7001 stuck in demo mode etc.

?

Also the built in Throttle did not work.
Re: YD7001 stuck in demo mode etc.

 

Also the built in Throttle did not work.
Re: YD7001 stuck in demo mode etc.

 

I managed to get the YD7001 after many hours work to get it on but having tried to connect a Z21 WLNA MAUS to the YD1001 it did not work .
?
All settings were correct but no luck, also tried a Digitrax UT6 via Loconet T socket that did not work either but it did before when connected to the ex DR 5000.
?
All cables were checked and working.
Re: Detailed setup manual for the YD7010?

 
Edited

Hi,

it's there, but still only in German:
Re: YD7001 stuck in demo mode etc.

 

Demo mode means no USB connection.

1) drivers not/not properly installed
2) USB connector nor fittet "deep" enoug in the DR500's socket
3) USB cable damaged/charge-cable instead of data-cable
4) USB Port on PC faulty
5) DR5000 USB connector faulty
6) DR5000 CPU faulty

but: "...?with only the Track power leds on...."?? which LEDs are you talking baout ? On the device or on the program ?

Greets,
Karst
Re: Detailed setup manual for the YD7010?

Rick Norell
 

Any word on a setup manual for YD7010 or quick start guide?? They had been shared earlier but were incomplete due to your writer being hospitalized.
Re: YD7001 | Resetting Command Station after Short

 

I have looked in the manual since finding this, and I have not found anything regarding short protection.
--

Heath @ Human[c]ity
YD7001 stuck in demo mode etc.

 

After installing a YD 9401 into my DR5000? and dowloading the config software, I then installed it,? the activation message did not appear.
?
The config software was re installed again still no joy, it was also tried on an other desk top computer and laptop with the same issue both pc are windows 10 latest version.?
?
At one point I did see serial number but still not working it is just stuck in Demo mode with only the Track power leds on.
?
The DR5000/ YD7001 has a new power supply YD7460 3.3A 18V.
?
I would also like to use the Z21 WLAN MAUS if possible.?
Re: DR4024 Servo decoder installation file.

 

Thanks Iain. You've come to the rescue yet again! I'll add it to the files section in the next few days.?

Matt?
Re: DR4018 CV Settings for Signal lights

 

开云体育

I have 4 x DR4018 running 32 x 2 aspect signals with CV47=2. The signals show steady lamps and fade gracefully between the aspects when changed.

?

You may have set the brightness too low and are seeing flickering because of this.

?

From: [email protected] <[email protected]> On Behalf Of Rodney via groups.io
Sent: 16 December 2024 21:47
To: [email protected]
Subject: DR4018 CV Settings for Signal lights

?

Has anyone been able to get the DR4018 to issue a steady Signal light when CV47 is set to 2 ?
DR4018 CV Settings for Signal lights

Rodney
 

Has anyone been able to get the DR4018 to issue a steady Signal light when CV47 is set to 2 ?
141 - 160 of 4740