开云体育

Correct, but use such a string in each TrackOut wire. :) 1N5402 is sufficient., it can handle 200 Volts. The 1N5408 800 Volts ;) Greets, Karst

Nope, works as designed. But.... The YD7001 can fully configure and address 1-128 inputs (8x 16-bit modules) Modules above are run in "legacy mode". That means that they get numbered as if it were

is there a bug in the software

';on the s88 bus module on the yd7001 the numbering of the sensors are correct in sequence up until 128 it says 8:16 then 129 shows 128 9:1 then they are all 1 out right up the scale can you help

Good evening. I have found in a Marklin Z forum in Spain what Mr. Karst indicates about using diodes in antiparallel. Now my question, what diode do you recommend? If the 1N5402 or 1N5408. In my case

can you explain this one look at the pics attached with the mouse over number 129 its shows 128 and 137 shows 136 and from then up over they are all 1 out

i dont?understand what you mean about out of spec when you said it was 5 mtr cable length?from the yd7001 I don't have any yd6016 lns what will changing the position of the dr4088 make

What if you swap Module 2 ( 4088-CS ) with Module 11 ( 6016ES-CS ) ? Although 4.9 is out of spec by 1.9 Meters for the YD6016ES's, people report this working ok. Otherwise only a YD6016LN-CS on pos.

The UP6Z wont help in this situation because the reduction in voltage needs to be after the YD6016xx and it needs at least 14v to operate. You would end up needing a UP6Z on every output from the

Mario, Digitrax offers the UP6Z 3 Amp Z Scale Voltage Reducer - " Reduces track voltage by 4 or 6 volts at 3 amps for safer Z Scale locomotive operation . . ."? This device meets your

Cable length in total is 4.9 mtrs module 1 is a yd6016es module 2 is a dr4088 module 3 to 11 is yd6016es looks like when plugin number 11 it knocks out 10 and 11 I have tried modules 10 and 11

pe, It needs a minimum of 14VDC to operate correctly: You can lower the output by inserting a couple of anti parallel Diodes between Track Out and your layout

a) What is the total s88 cable length ? ( from Command Station until the last module ) b) What modules are #1 thru #9 ?

Good afternoon. Could you put the transformer that has the Marklin Z controls that I think are 10 volts or 12 volts and use it directly with the Yamorc yd7001-e? If it were possible, how would you

Hello all well considering when i turned off last night everything was running just fine. all my yd6016es are coupled together with patch cables back to the yd7001 ext in (NO e-Link connection) turned

Karst I have 4 @ DR5003 boosters and a YD7001 command station “All this was for us the reason to (let) produce our own PSU's to our own specs. A decent alternative to those are the GSM60A15-P1J (

It the usual Digitrax documentation, they just copied a paragraph from ordinary decoders onto the TF4 manual. If you search hard enough you will discover that a TF4 can't be read. Got the tee shirt,

Hi Caz, It's confusing, documentation says that you can read and write but I can't get it to read.? Anyway, I can write and its now working. Thanks everyone for your help. Alan

What is the error message you receive ?

You can Link 16 in total: Of which only 8 can be configured individually. But as you already have 12, that does not seem to be a problem ;) Greets, Karst P.S. Note: The total RJ45 cable-length