开云体育

Keep in mind that the VARA modem is adaptive. It will start out at a high rate and the sending station will transmit a five second data burst, the receiving station will then transmit a short ACK

Good evening all, I have a similar situation, but different set up. ?I am running an IC 705 (10 watts). ?I have it connected wirelessly to my MacBook (I can either direct connect or via router).

How is PTT being managed from the Winlink end? Is there an expectation that VOX is being handled inside the SignalinkUSB to do the PTT, or is it via CAT Control? Personally, I use CAT Control and I

Check to make sure that Left or Both are selected for the output device channel (not right).? The SignaLink, while including a stereo CODEC, does not process "right" channel transmit audio. Kevin

Forgive me, folks, I'm old and didn't the message part about Vara FM. I find that the USB audio codec needs to be Mic (Record)> 2 on the sound menu setting. Speaker (Playback) set at 100%? 73 later

Barry K3EUI Does he have the early version of the Signalink? In the VARA FM, I assume the PTT has been set up for that radio model? 73 Don VA7DGP/VA7QU

A friend of mine has the following: Yaesu FT847 and a SignaLink sound card and VARA HF sound card modem (latest version) He has this combination working fine on HF bands with Fldigi and the SignaLink.

Well, the obvious questions are is Vara already running when your application completes initiating? Is your application the one starting Vara? Is Vara and your application configured to the same and

D74 works fine for VARA FM and a DigiRig. Checkout this video for an approach to create a portable setup with it: https://www.youtube.com/watch?v=7bOmWUk1XhM

This is the response I get when I try to start a VARA FM session...I have yet to successfully use VARA FM....Packet Winlink works as it should....

I have vara fm working well with my kx3 and ic705. Is there any reason I will be frustrated getting it to work with a kenwood d74? I am looking at a Didgirig for the d74. My kx3 is interfaced with a

I have two radios, both used on a Masters DRA-45. Both radios show auto tune / ping of S/N 19 to 24 depending on conditions, and VU - 20. I am communicating / testing with an RMS set to wide. The

John; What is your "other radio", and what are you using for the rig-interface device? How is the rig-interface device connected to the "other radio"... data jack (mini-DIN6), or mic/spkr

I found that by using VARA Narrow, the radio will pass around 9 to 11,000? on transmit and about 7,000 on receive.? So I also tried my other radio on Narrow and found that? some times it is faster

You can download it without putting it in the cart and therefore without paying anything. It will run in a limited mode where it does not save the settings after a reboot/restart. It will prompt to

Are you sure about the HHD being free for non-commercial use?? Maybe I missed it but it looks like either $90 or $150 to me.

Hi Grant, Following the suggestions of the others, get your COM port drivers loaded from Yaesu, and Winklink loaded. Once you get those COM ports working, and the software running, use the attached

[email protected]> wrote: Starting up the progam automatically upon reboot isn't the issue. After a reboot you have to re-split the port manually.

I'm using the toolkit at https://hhdsoftware.com/virtual-serial-port-tools to split the PTT port on an FTdx10. It's free for non-commercial use. I'm looking into com0com / hub4com for a solution that

Thanks for the APRS links.? This is something I'm researching with interest.? ?It would be of great benefit here. Is it possible for one instance of VSPE running to have two different splitters