开云体育

Wow. That is going to be a great road trip. I live in the Four Corners area about 8 miles SW of Durango, CO. One thing to note,,, re the Four Corners monument,,, you cannot drive to the point of the 4

Hello everyone. So I haven't fixed the issue yet. So I think the problem is under the following: Under VARA HF WinLink Session Under Settings Under Radio Setup Under PTT Port Should be: Y8x7 But now

[ 11:00? PM EDT? 6 Oct / 0300 UTC 7 Oct] I am currently observing a dramatic demonstration of how overwhelmingly superior VARA is? compared to classic AX.25? HF packet. ? At this time, there is a

Over the period? 8 October 2024 to 26 October 2024, I will be on another extensive road trip, running HF APRS both over classic AX.25 packet, and over VARA. A friend of mine is flying from Los

I found a solution to this problem.? Setting the radio model to IC-7600 instead of IC-7610 allows everything to work and it no longer switches MOD input from LAN to AUX. Thanks to everyone that

The setup is pretty clean. There's plenty of docs out there, I believe Winlink has some also. Is there something specific that you're coming across? Greg KD2MIC

K4HVF here with a question about setting up a VARA FM only gateway without packet. I have a Yaesu FTM 400XD and a Signalink USB with the 9600 bps module installed. With this setup I can transmit

Here is what my settings.? I am using SignaLink USB. Also here are the last 2 lines in the cat command ini file for FT-891 VarACStartCmd=ST0;SH0010;? ?(turn of SPLIT and change width to 500Hz)

Hi PatMc, It does as you said, puts my 7610 in data mode USB and sets the freq but it also changes the MOD Input from LAN to AUX.? Everytime I click a channel in Winlink it does this.? I have to go

I use flrig for ptt. It works well for me.

Winlink doesn't change the MOD Input. ?It selects a digital mode (e.g. Data 2) and then you get whatever the input is for that mode. ?Look at the radio when you are transmitting; you should see a D

Hi Merlin, pse fill in the details like shown in the yellow part for use with a COM Port (I'm using TCP): Depending of how you set up the Data BFO, you might want to change in VarAC_cat_commands.ini:

Sorry I misunderstood. I’m using USB Larry KF5MLP Sent: Tuesday, October 1, 2024 8:59 PM To: [email protected] Subject: Re: [VARA-MODEM] VARA HF using Winlink on IC-7610 using LAN connection Hi

Hi Larry, I can make it work with the USB cable.? But I want to use it remote on my network.? Are you using it via your LAN or USB? Thanks, Joe

I have a IC-7610 and I use the radio and not LAN setings. I can show you how. Send me an email off line. I’m good on QRZ. Larry KF5MLP Sent: Tuesday, October 1, 2024 4:55 PM To: [email protected]

Hi, I was able to get Vara HF with Winlink working on my IC-7610 using the icom utility LAN connector on my home network with the exception of one problem. When I choose a channel in Winlink it

WinLink Vara HF works quite well on the 891.? VarAC receives but no PTT or rig control, latest CAT command file in use.? What have I missed?

Keep in mind that the VARA modem is adaptive. It will start out at a high rate and the sending station will transmit a five second data burst, the receiving station will then transmit a short ACK

Good evening all, I have a similar situation, but different set up. ?I am running an IC 705 (10 watts). ?I have it connected wirelessly to my MacBook (I can either direct connect or via router).

How is PTT being managed from the Winlink end? Is there an expectation that VOX is being handled inside the SignalinkUSB to do the PTT, or is it via CAT Control? Personally, I use CAT Control and I