开云体育

I assume the G90 is for the HF side. I don't have HF yet but I will. My current set up: - I am using a BeeLink Mini PC running Windows 11 Pro. - I am using two Digirig Mobile and two Yaesu

I didn't mention Vara FM, depending on what sound card. I know the digirig will need a comport to PTT the VHF radio. 73 *Don PoapsNew Westminster, BC*VA7DGP DATA VA7QU VOICE *Winlink:

I'm not sure what your getting. I see 2 soundcards. I know what the G90 does and I have used my digirig with. I have no idea what the FT 2980 does. I have a Motorola radio using a (VHF) 9612 Kantonic

Also, I forgot to mention - the initial successful connection was with a rubber duck on the HT, after that I switched to a gain antenna on the roof. I also tried going back to the rubber duck, but

I always select VARA FM Winlink for my sessions. Also, the gateway is just 7 miles from my QTH, and I have no problem connecting with a packet node (2m) that is 20+ miles away. I literally had just

The message in the outbox won't affect the connection, but selecting VARA FM P2P vs VARA FM Winlink will. Dave I've been able to use an HT to connect to Winlink gateways that were either really close

Yes, I'll check, but I never have used P2P, so I'd be surprised if that was the case. [email protected]> wrote:

Another guess. Is the message in your outbox set as Winlink, instead of P2P? If set to P2P, then unless you are connecting to a node that is in P2P listening mode and also is the callsign your

Mine connected to Radiomail by selecting the VR-N76 in Radiomail itself. Same with aprs.fi. It doesn't seem to connect via the BT page in settings for those, but I have tried with multiple iPhones and

Hello Mark, Yes, I tried autotune and ping - no response. The last time something like this happened, I found it was because I was selecting VARA FM Radio only. Once I selected VARA FM Winlink,

Have you tried running an "Auto Tune", from the VARA FM "Settings -> SoundCard..." window? On your 'monitor' radio, you should hear all 10 signal bursts at increasing audio levels. Many radios stop

Has anybody gotten their hybrid RMS gateway successfully configured? I’m running relay, packet and trimode but I don’t want to tie up my 705. I’m using a g90 and ft-2980, is it possible to put

FWIW, I have tried a range of TX drive levels, but still no joy. Since the hardware works with my packet setup, I have to think it is something in RMS Express or the VARA-FM setup, but I changed

I had finally figured out how to use Winlink with VARA-FM and an AIOC into both a Baofeng and an Anytone 878. I also use the same hardware configuration for Direwolf/Outpost packet BBS

Got it running. In Windows 11 there ?is a legacy program for sound under More sound settings and under the mic Custom tab there is a AGC box I had to click off that got turned on from a Microsoft

There are two radio shacks at my home. Mine upstairs connects to the east side antennas. My spouse’s shack connects to west side antennas. My Yaesu 857 connects to HF and Fm Winlink with no problem

?After a freakish warmup here in central Michigan to 50 F / 10C for the last two days (it was -2 F / -19 C Sunday night), the snow and ice melted allowing me to get outside and do some antenna

Hello, Facundo, I use an IC-7300 for HF Winlink. The Icom driver software puts two com ports on the computer. Only one works with RMS Express email. For the 2m Winlink gateway I am using a

Brian, Can't imagine what could cause this. Which DRA (and if it is a VOX capable, is it jumpered for VOX?)? Anyway, this is a Vara group, so I don't really want to continue down this path here.

Make sure your TX level is not set too high. Most Icom rigs will not go into TX if the audio drive is too high. -Scott, NS7C