开云体育

Made a couple updates and bug fixes. Still in beta! But it works great!

Did you solve this problem? Please let us know. [email protected]> wrote:

I know it isn't exactly what you asked, but I was able to install cheap 128gb SSD's in both of my Chromebooks and now run Linux on them. After taking the many screws out to split the case, just

Marek SP5ISZ Going by what YouTubers say, "Radiomail" the author was working on getting the IOS cell to work. It would be a firmware update. 73 *Don PoapsNew Westminster, BC*VA7DGP DATA VA7QU VOICE

@Steven, @Don, Thanks for your replies re. Vara FM over Bluetooth KISS TNC. I continue to build an audio interface (600 Ohm transformers, optocoupler for PTT), so I should be able to proceed with the

I have previously used VARA and VarAC on Lubuntu 24.04 LTS without any issues.? It was stable and working correctly. However, in the past week there has been a version upgrade of Wine 9.x to Wine

This is the method I use to execute bash commands within a .desktop file automatically at startup: https://www.linuxuprising.com/2020/11/how-to-launch-startup-applications-with.html?m=1

Make sure the SignalLink Delay is OFF

Following is the terminal command that I use. wine c:/VARA/VARA.exe My setup is a Pi4B runnin on 32-bit Bookworm. This is my first attempt at a Bash script to start Vara and wait until it is running

Hello, recently I purchased and reflashed Lenovo N23, 4GB RAM, 16 GB flash. Running JS8Call to my complete satisfaction, using QDX and/or QMX transceiver (both have built-in USB CDC's for serial and

Smiley; You made it clear in your original post that you're using a SignaLink as a rig-interface device with your Alinco DR-B185 radio. I don't know why people are giving you guidance relative to

Packet TNC expose a digital interface, namely the bottom half of the AX.25 protocol. Think of a TNC as a hardware modem (MODulator/DEModulator) + sound card + PTT control. With AX.25 the modem is

I certainly like to see some like that. I have ordered one and Vero N76 is the cat's meow. 73 *Don PoapsNew Westminster, BC*VA7DGP DATA VA7QU VOICE *Winlink: va7dgp@...

Just a side note: a bit off topic. This was so much easier with the Japan made 2m Alincin DR-135 radio with the DB9 connector and data mode setting in programming. It works great with the Repeater

Vara is an audio mode so the hardware KISS TNC won't work. You can still use the radio but with an audio device and proper cable. I have one of the BTECH UV Pro rigs and it runs packet like a scalded

To me, one would need to have RJ45 and a speaker plug running from the Digirig. I would have squelch off and the audio up per the Vara TNC. I see a data port but from the manual, it's for Cloning.

Greetings, Recently a handheld radios known as VERO VR-N76 (with two siblings sold as BTECH UV Pro and Radiooddity GA-5WB) received a firmware upgade, which made a KISS TNC available over Bluetooth to

It seems that you have found the problem area. No PTT signal. I don’t know how the SignalLink works for PTT. Does your packet modem software use VOX or a com port? [email protected]> wrote:

Ra board responds ra board not found. It is currently set on vox. ?? 73 smiley - kz4zk On Thu, Feb 6, 2025 at 16:49, Bob W0EG via groups.io<morrisnc7@...> wrote: What is your PTT via

What is your PTT via setting in VARA? Likely should be RA board. [email protected]> wrote: