开云体育

The following items have been added to the Files area of the [email protected] group. /ASL3/Kits 4 Hams suggested SHARI settings for ASL3 v1.01.pdf By: N8AR <n8ar73@...> Description: This document contains Kits 4 Hams recommended settings for the SA818 and simpleusb in SHARI Allstar hotspots. Revision 1.01 adds the commands to invoke SA818 programming and simpleusb setup.

The following items have been added to the Files area of the [email protected] group. /ASL3/Kits 4 Hams suggested SHARI settings for ASL3.pdf By: N8AR <n8ar73@...> Description: This document contains suggested settings for the SHARI SA818 andASL3 simpleusb when setting up ASL3

I purchased the Pi5 kit from kitsforhams.com and have it assembled. I have installed and setup ASL3 but i cannot get the node to work. I am getting error messages when applying the settings to the SA818 chip. Is there a write up detailing the settings specifically for the Pi5 Shari hat?

Good morning to the group. This is my first time posting, so if I'm in the wrong spot, i apologize. So, over the last year or so, every once in a while ill go to use my node and I get nothing. No courtesy tone after TX, no boot sounds, no nothing. Also, no LED's on the Shari unit are lit. And the issue is intermittent. It doesn't do it all the time. But now, its doing it all of the time. Unfortunately, I didn't build this node, so I am starting from the beginning here. The gentleman who built it, installed an external mic jack, external speaker, and switch (for hand mic or HT use). There are 6 wires coming from the Shari unit that go to the switch and there's also another 2 wires that go to an audio gain pot for the external speaker that was put in the unit. I couldn't find a schematic, just construction instructions, and they don't tell you much besides how to assemble the unit. From what I can gather, the wires coming out of the Shari unit are NOT "factory" and I'm guessing was a modification of the original design. Id be entirely okay with just getting rid of that darn switch because I always use an HT. However, I would like to keep the external speaker/ AF Gain pot because its pretty convenient not having to have an HT on all the time to be able to hear whats going on. Has anyone experienced something similar? Any help would be great.

It is possible to configure shari with iaxrpt, I have tried to follow the instructions I found on the internet but without success I do not know where the error is Enviado con Mailsuite · Darse de baja 14/10/24, 05:08:37

My newly-built ASLv3 + SHARI node will connect done to 55553 and a couple other nodes, but I get “connection failed” for most others. I’ve found posts that say it could be that my IP address changed since those nodes last pulled the ASL registration details, so the nodes are rejecting my connection request. Does anyone know the default interval for these requests and/or if there’s a way to check or force update the list? The check really should be dynamic - call the API on each request vs storing a giant, outdated list locally. The connection log is empty so no help there. I have a a one node and I can’t even connect to that one. Any help troubleshooting or files to check would be appreciated a. Chris Baker https://www.linkedin.com/in/cwbaker https://twitter.com/bakerc

On my SHARI Pi4V, everytime there is an Rx sent to the radio, I get what I would call "roger beeps" but no voice. I attached a video showing what is going on. I went through the setup that was sent with my SHARI and the document on this group. Anyone have an idea what is going on? It does this on all my radios. I have two UHF SHARI and they both work fine, just a problem with the VHF node. I tried a different frequency just in case I was too close to something else in the area but it made no difference.

Hey folks. I have one of these fine machines on a pi. 3. I do want to move it to a pi. 4. And I think I can do it with just a couple of USB cables. Anyone else done this yet and had success? It looks pretty simple. Two USB extension cables a footlong. Thank you.

I set up a node with a borrowed SA 818 on my Pi 5 using All Star 3, which was working well. I have returned the SA 818 and am wondering if the programming stored on the Pi SD card will work with a replacement SA 818, or whether further re-programming is required to operate the replacement 818 I'm not sure what if any setup is done on the 818 that is not stored on the Pi SD card Any information will be welcome Thanks

Hello All! I recently had a hard drive 'crash' (SSD). I had saved what I "thought" was sufficient data to restore files, programs, passwords, etc. Having slowly gotten most of what I want/need, I tried to login to Supermon. I got the "Login failed" response. "Someone" told me the 'default' login user name is "admin", which I used. Apparently I have forgotten my Supermon login password and I am unable to find it, ANYWHERE. There appears to be no "Forgot your password" option, as there is for virtually every other web site, program, etc ON THE PLANET! In any case, I am 'pleading' with anyone who can help and/or steer me in the right direction. I am hoping I do NOT have to completely re-install/configure my Raspberry Pi. Thanks and 73, Larry - K7LRB

I had to reinstall ASL 3.0 and am able to get the allstar node with a good connection to the allstar server. There are two areas I am having issues with 1) Where do I test my DTMF settings? When I do a aster cli I see multiple lines scroing. UNable to connect to another allstar node 2) Echolink with ASL 2.0 was no problem on setting up. It just that ASL 3.0 I am not connecting to the echolink servers. I have verify node number and echolink password. 3) Also the COS LED is not working. For me to see the text configuration file I had to turn syntax off. K6DLC

N8AR <n8ar73@...> added folder /How To Description: This folder contains various documents explaining how to do certain tasks related to a SHARI node.

I am wondering why that the setting for led cos is not in the rpt.conf as an option within the image download file? K6DLC

The following files and folders have been uploaded to the Files area of the [email protected] group. /SHARI PiHat Mod2 52Pi case Documentation/How to enable the COS LED for ASL3 Alllstar Image.pdf By: N8AR <n8ar73@...> Description: This documents shows how to enable the COS LED (yellow) when using the ASL3 image.

Hi I'm trying to install shari on deb 12 can someone help me please

I am running a yaesu ftd5 and have used the method documented on this site to attempt and set dtmf tones. Everyone of the codes except the 'A' tone work. I have adjusted the receive volume. Any suggestions. I can live with out the 'A' tone, but would like to get it working.

I have my shari node working on allstar. I am trying to get it to work on echolink. I have enabled the echolink.conf file and filled in the proper settings: [el0] confmode=no call=your-KI5KEE-L ; Change this! pwd=your-ccccccccc ; Change this! name=John Hutchings ; Change this to your real name! qth=Paris TX ; Change this to your actual QTH! email=john@... ; Change this! maxstns=20 rtcptimeout=10 node=597257 ; Echolink node number - Change this! recfile=/tmp/recorded.gsm astnode=60017 ; Change this to your active Allstar node number! context=radio-secure server1=naeast.echolink.org server2=nasouth.echolink.org server3=servers.echolink.org server4=backup.echolink.org ; I have opened up tcp and udp ports 5198-5200 and pointed them to the shari node. Allstar4569, 5198-52004569, 5198-5200192.168.1.49 both udp and tcp inbound and out I am trying to validate my KI5KEE-L address through Echolink and it says it cannot ping it. That is the first problem. Second is this: Verbosity is at least 4 -- Received OK from Echolink server nasouth.echolink.org -- Received OK from Echolink server naeast.echolink.org [Sep 10 11:14:59] ERROR[1810]: chan_echolink.c:2302 do_el_directory: Error in parsing header on nasouth.echolink.org Any help would be welcomed.

Hello all, I'm building an allstarlink node with a raspberry pi 5 with a Shari pihat and I can't program the sa818. The node works with the default sa818 settings, but when I try to change settings using "sudo sa818-menu" I get a connection error. Anyone run into this problem? Any ideas how to fix?