开云体育

Folks, I can confirm what Steve says about SMA RF press-in barrel connectors. I have one of the early Shari Pi3U's that used this connector and it did come loose. It was impossible to reseat it

Start by analyzing your audio digitized by the CM108B.? I suspect you will find that your audio is fine.? This document in the Files section of this group tells you a way to do it.

Folks, I have both PiHAT VHF and UHF. I connected to a node that is also bridged over to an XLX Reflectors. I have tried many different radios, be it HT or even based rig with V-U capabilities. My

Thank you Steve and Luis for the picture, Helps a lot. Will give it a go when I get my pi-hat. Thanks again. Dave/AD4UU

I have for sale A fully assembled and tested SHARI PiHat kit with Pi 4-2? asking? $200? VHF module.? I also have a? UHF Module also if you want UHF instead of VHF. text me for more info

I think PP23 is Black (D-) and PP22 is Red (D+).? If that doesn't work just swap them

Hello Steve, Thanks very much for your response.? Attached is the picture on one of my Pi 3 A+ boards.? Showing PP23 and PP24. Are these the same as TP23 and TP24.? I would solder to these two pins

Like this or is it the other way around?

Solder the red and black wires to the test pads associated with the two middle pins (Tp22 and TP23) of the USB connector.? Looking at a picture of the bottom of the board on the web, I think the

I have on order a pi-hat that I would like to use with a pi 3 A+ board. Be a great portable package. I am seeing great documentation on the pi 3 B+ with pictures on were to solder the wires for the

I misspoke, I meant the SHARI software stack as implemented in support of the Kitsforhams SHARI when I said "the Allstar software." When you use a different processor and have to cobble your software

Hello all, I too will attest to the amazing quality and superb support provided by Kits For Hams (KFH). Being (and still am) a novice on Allstar, this was my first experience with this technology, so

Also, We need to support those who support us. Kits for Hams is always there to help. Rich Sent: Friday, February 3, 2023 11:18 PM To: [email protected] Subject: Re: [SHARI] Libre SBC, and also AURSINC

Thank you all for making my decision to shun the Aursinc clone as easy. I will be placing an order for the authentic Shari right away. I saw the clone on Amazon and thought it was a maybe, but your

Hello Steve/everyone. Thanks for the detailed response back on the Aursinc. It's a good thing that some new hams will ask about this first before they purchase. Unfortunately not all of them ask first

Hmm, AllStar was originally written for the i386 architecture, and later was ported to run on x86_64 and ARM.? You may be talking about HamVoIP, but there's nothing stopping one from attempting to

The Aursinc SHARI is a Chinese ripoff clone of the genuine SHARI by N8AR. There are numerous problems and issues with it. First and foremost, according to FCC, it is illegal for sale in the US because

Short answer, the AURSINC is a knock-off/clone, it has been known to have issues, and the kitsforhams fellow will not provide assistance, since he gets no revenue from the sale. As for RPis, the RPi

Hello everyone, Just about to start tinkering with AllStar, and after some reading, I hoped to hear a couple opinions from the many of you with experience. Firstly, I would like to use anything other

Out of curiosity, which mesh system are you using? I try to use Ethernet wherever I can, but if I must use WiFi, and it doesn't move around too much, I make sure to lock the device to the closest