开云体育

Did that Sent: Thursday, December 8, 2022 2:46 PM To: [email protected] Subject: Re: [SHARI] Pi3 will not boot when SHARI PiHatU GPIO connector is plugged in Or just reseat the sdcard. Forgot that easy

Or just reseat the sdcard. Forgot that easy step. -Michael Sent: Thursday, December 8, 2022 10:21 AM To: [email protected] Subject: Re: [SHARI] Pi3 will not boot when SHARI PiHatU GPIO connector is

Ok a good thought Sent: Thursday, December 8, 2022 10:41 AM To: [email protected] Subject: Re: [SHARI] Pi3 will not boot when SHARI PiHatU GPIO connector is plugged in Do you have another SDcard you can

Can you SSH into it? Can you see the node at allstarlink.org?? (under Lists-Stats click on Active node list and in the FILTER box type in your Call... You call should be green At Kit's for hams there

Do you have another SDcard you can use? Build a new one and test. -Michael Sent: Wednesday, December 7, 2022 3:02 PM To: [email protected] Subject: Re: [SHARI] Pi3 will not boot when SHARI PiHatU GPIO

It stays powered up the lights stay on Ill read and watch voltage Sent: Wednesday, November 30, 2022 6:20 AM To: [email protected] Subject: Re: [SHARI] Pi3 will not boot when SHARI PiHatU GPIO connector

Yes....tried a bench power supply that's good for 10A...unfortunately, same result.? I'll try to capture the rapidly-scrolling display on my cell and see if I can discover what the last few lines

I have an All-star node that was built for me. Its been off line for 6-8 months How do I get it restarted. It shows on my network for all but 1 minute then locks up. I have a red and green lite on the

I've chosen my words poorly! MY BAD! I stay connected to the Wifi on the Pi, no problem, but! If I am using WiFi, I can't stay connected to other nodes. Connections to other nodes get dropped at

Yes the Shari is only 3 ft away from the hotspot on the phone. Not sure about the 5ghz connection? It's a wifi hotspot in my cell phone, so it is, whatever it is, I can't change that. The PiHat in the

Is there a program I can use to adjust the receive attenuation of the radio? -- L. David McLennon VO1LM, VO1LDM 3.740, 146.940 Director, SONRA 54 Hawker Crescent St. John's, NL A1E 3W4 709-682-8752 -

Is your hotspot close to your node so you are receiving a strong WiFi signal.? The all metal Unistorm case will attenute the WiFI signal some.? It should be fine if you are close to your hotspot

Just on WiFi. It has been pointed out that my phone company may be using double NAT. But I have been able to use the phone hotspot on other Shari nodes without any problems. I've got an original Pi3V

Do these symptoms occur while you are using a wired Ethernet connection or just on WiFi?

Have you tried a good, stout 2.5-3A power supply? -Pres W2PW

I am getting this error. [Nov 28 16:36:32] ERROR[370]: app_rpt.c:12333 rpt: No link messages from [502690] in 48 seconds -- One way audio?? Forcing reconnect. I've been fighting with this for a few

Excellent. I am not a fan of the arch linux part of hamvoip, but the rest makes it an easy solution. Especially with the DAHDI drivers being a pain to get compiled on a pi. -Michael Sent: Friday,

Knowing where in the boot process it reboots would be helpful. Can you record the screen on a cellphone and then transcribe the last few lines before reboot OR share a link to the video. Ken, N2VIP

The display shows the typical linux boot sequence. If J1 is connected then the Pi reboots constantly part way through that listing.

Hi Michael, Thanks for the reply.? You are correct.? There were quite a few corrupted files in the python directories.? Before I attempted to re-program the SA818, I created a backup of the