开云体育

I also don't have those on my Pi running the HamPi V1.0

AX 25 services issues pi@raspberrypi:~ $ cd pitnc pi@raspberrypi:~/pitnc $ sudo systemctl start ax25 Failed to start ax25.service: Unit ax25.service not found. pi@raspberrypi:~/pitnc $ sudo systemctl

see below <mdgriffith2003@...> wrote: wl2k VA7DGP 1200 255 7 Winlink tnc VA7DGP 19200 128 2 TNC-Pi2 VHF

This is the second report I have seen. I will try to get time to investigate this weekend. Please include the generation (or order number) of your DRAWS? board. -- John D. Hays Kingston,

Hi everybody, I just got the HamPi to work on a raspberry pi 3b+. Since I do have a DRAWS hat on top of it I would like to activate it. So I followed the instructions. I uncommented the lines in the

Don, If you have the latest Raspbian Buster installed, AX.25 is already there and ready to go.? However, you need to edit a couple files to get it setup.? The PiGate software does this for you, but

I got the Pi TNC from John Hanson a few years go. It's been sitting on a PI 3. Theres 2 modes I want to do. APRS and Pat Winlink. I know I have to do a Kissattach /dev/serial0 or something like that.

Don, When you connect through PuTTY, is is through an SSH or Secure Shell TCP/IP connection port, not serial.? VNC is also through a direct connection at a non-serial port. Where did you get the

That is far as I got as well, I can see /dev/serial0 0 and /dev/serial1 0. I need the 6 pin to work. I try the kissattach command. Shown on getpat,io. 73 Don va7dgp

EXCELLENT!! So after six tries because it is early and I simply can’t type (and I have learned Linux is very unforgiving on typing!) I got the following: Using Serial Port

That was my reaction as well, but every reference I can find looking for a “manual” points back to the TNC PI. It was an impulse buy to see about getting a mobile packet station and the ability

Don, First, you'll also need to use the raspi-config utility to enable the console serial port, but disable console login. Run "sudo raspi-config" Then go to menu 5, Interfacing Options, then menu

Don: Just covering the obvious here but the TNC-Pi is a completely different product than the TNC-Pi9k6 and the instructions for the TNC-Pi are not applicable to the -Pi9k6. Steve N8GNJ

First I am an operator and not a technician.? I can follow directions and to some extent do enough to get myself in trouble.? Having said that I purchased a TNC9k6 and have it running wiht a

On point 1, kernel AX25 has various display options for mheard that can be found here https://www.unix.com/man-page/debian/1/mheard/ I don't know if other variants of AX25 offer the same options

Also use notepad++ on windows for editing scripts. You can set it up to use *nix formatting, and it supports colors too. Also WinSCP is great for managing files remotely over a SSH connection also.

I believe you are running the old version, not the recently released one, so it's not there ?Get BlueMail for Android ?

someone else (?) mentioned wifi/bluetooth on the same freq may be an issue... I'll check as both may have been on. Power is not a problem. I am using a power/fan hat that is fed with 12V. I am

Hi Dave, "No, I do not wish financial compensation for this. However, I do have a PDF on the desktop called "GIVE BACK' which outlines two charities I support. I would appreciate donations to be sent

I got my downloads from the Kilo Prefix worked fine Dave Slotter reported some ArmChair Lawyer Gripes on Git Hub, so he pulled the download off that site until it cooled off etc. The Prefix mirrors