R1CBU@groups.io | Messages

Re: r1cbu v0.17.1

But 0.17.1 is available on Oleg's website.

The link says 0.17.0, but on that page you can see that it is actually 0.17.1

Re: r1cbu v0.17.1

#38

Please try not to post the same question 3 times to the same group, that is generally considered to be very very rude.

r1cbu v0.17.1

#37

good evening, can someone send me the r1cbu 0.17.1 firmware please, antoniojoselop@...

thank you 73

?

r1cbu

#36

good evening, can someone send me the r1cbu 0.17.1 firmware please, antoniojoselop@...

thank you 73

?

r1cbu

#35

good evening, can someone send me the r1cbu 0.17.1 firmware please, antoniojoselop@...

thank you 73

?

X6100 screensaver

#34

I only use my X6100 while plugged into a DC power supply. Is there any way to set the screensaver so the screen stays on until the radio is turned off?
Thanks,
K5UTM

Using V19: hot sure how to set up my CW paddle

Howard Sawyer

#33

Used this firmware for the first time today on SSB. I like it; however, when I tried to operate CW, I realized I have to add settings for my preferences; eg Iambic settings.

How does one do this?

Thanks,

KO6WL

Re: v19 no CAT control problems

#32

I rebuilt hamlib to latest and greatest version.

1. x6100 works find instead of 5105

2. rigctld works great.

3. flrig still doesn't work.

so, for now, i'm done with flrig

Jerry

----

Extra Ham Radio Operator: WF5W

Registered Linu=x User: 275424

3D CAD designer

The most exciting phrase to hear in science - the one that heralds new discoveries - is not "Eureka" but "That's funny...". - Isaac. Asimov

Show quoted text

On Tue, Dec 12, 2023 at 9:17?AM W8ISM via <W8ISM=[email protected]> wrote:

I also use linux mint and v19 - everything works fine. I assume you are using cmedia input/output on the audio page, so the only thing I would try is setting the device to x5105. I think sometimes hamlib lags behind updates.

Re: R1CBU and digital modes

#31

I found out you couldn't just use -L

you had to specify the radio and then -L

so ... rigctld -m xxxx -L

I had no trouble with x6100, but I just rebuilt the hamlib with the latest and greatest version

Jerry

----

Extra Ham Radio Operator: WF5W

Registered Linu=x User: 275424

3D CAD designer

The most exciting phrase to hear in science - the one that heralds new discoveries - is not "Eureka" but "That's funny...". - Isaac. Asimov

Show quoted text

On Tue, Dec 12, 2023 at 9:24?AM W8ISM via <W8ISM=[email protected]> wrote:

rigctld -m 3087 -r /dev/ttyACM1 -s 19200 -C stop_bits=1 &

This works for me on Linux mint with stop_bits not stopbits. See the man rigctld. Use regctld -L to see all devices. For JS8 I need to use X5105 which is 3089.

Re: R1CBU and digital modes

#30

rigctld -m 3087 -r /dev/ttyACM1 -s 19200 -C stop_bits=1 &

This works for me on Linux mint with stop_bits not stopbits. See the man rigctld. Use regctld -L to see all devices. For JS8 I need to use X5105 which is 3089.

Re: v19 no CAT control problems

#29

I also use linux mint and v19 - everything works fine. I assume you are using cmedia input/output on the audio page, so the only thing I would try is setting the device to x5105. I think sometimes hamlib lags behind updates.

Re: R1CBU and digital modes

#28

Had not run R1CBU with FLrig. Tried both R1CBU 0.17 and 0.19 with FLrig 1.4.7 with same results. FLrig to talk to X6100 using FLrig's X5105 driver. best with the Xiegu fw In addition, FLrig would change some X6100 settings (VFO & its freq), but not read any X6100 values.

Must be a R1CBU CAT handling bug, as FLrig 1.47 works pretty well with the X6100 using Xiegu fw, especially with FLrig's IC705 which has more functionality than its X6100 driver.

Al Pawlowski
Los Osos, CA USA

Re: R1CBU and digital modes

#27

On Sun, Dec 10, 2023 at 10:45 AM, WF5W wrote:

rigctld -m 3087 -r /dev/ttyACM1 -s 19200 -C stopbits=1 &

Thanks WF5W - was struggling with JS8.

Re: R1CBU and digital modes

#26

Ok. Update.

It does work.

Flrig somehow won't talk to it. But if I use hamlib DIRECTLY, it all works.

$ rigctld -m 3087 -r /dev/ttyACM1 -s 19200 -C stopbits=1 &

and set all my digital modes to use hamlib

Jerry

----

Extra Ham Radio Operator: WF5W

Registered Linu=x User: 275424

3D CAD designer

The most exciting phrase to hear in science - the one that heralds new discoveries - is not "Eureka" but "That's funny...". - Isaac. Asimov

Show quoted text

On Fri, Dec 8, 2023 at 10:10?AM Jerry Davis <wf5w.ms@...> wrote:

Ok. I have tried everything known to mankind, to get digital modes to work with R1CBU.

It was my understanding that R1CBU was just a different GUI, on top of the radio. It is NOT.

So at first I thought that flrig was at fault.
So I booted up the default rig, and changed wsjtx to use IC-705 and set it up for CAT control. It worked flawlessly (via ttyACM1). So, I knew that everything was working.

I rebooted into R1CBU v19. And I didn't use flrig either. So all I was using was the hamlib part of wsjtx. Same IC-705, same CAT control parameters. Nothing. So, I can only come up with the conclusion, that R1CBU doesn't work with digital modes.

Too bad, I wanted it to, so bad. I like the interface.

Jerry
----
Extra Ham Radio Operator: WF5W
Registered Linu=x User: 275424
3D CAD designer

The most exciting phrase to hear in science - the one that heralds new discoveries - is not "Eureka" but "That's funny...". - Isaac. Asimov

Re: R1CBU and digital modes

#25

I've been using it for all digital modes with my Surface and it works flawlessly. The only time it acts up is when the battery is low.

This firmware is light years ahead of the stock.

Good luck!

Re: R1CBU and digital modes

#24

Ok. Not clean but I got both ft8 and js8 to work.

Flrig would not work in any case.

FT8 works with newest version of hamlib

JS8 only works with command line rigctld

Jerry

Show quoted text

On Fri, Dec 8, 2023, 10:10?AM WF5W via <=[email protected]> wrote:

Ok. I have tried everything known to mankind, to get digital modes to work with R1CBU.

It was my understanding that R1CBU was just a different GUI, on top of the radio. It is NOT.

So at first I thought that flrig was at fault.
So I booted up the default rig, and changed wsjtx to use IC-705 and set it up for CAT control. It worked flawlessly (via ttyACM1). So, I knew that everything was working.

I rebooted into R1CBU v19. And I didn't use flrig either. So all I was using was the hamlib part of wsjtx. Same IC-705, same CAT control parameters. Nothing. So, I can only come up with the conclusion, that R1CBU doesn't work with digital modes.

Too bad, I wanted it to, so bad. I like the interface.

Jerry
----
Extra Ham Radio Operator: WF5W
Registered Linu=x User: 275424
3D CAD designer

The most exciting phrase to hear in science - the one that heralds new discoveries - is not "Eureka" but "That's funny...". - Isaac. Asimov

R1CBU and digital modes

#23

Ok. I have tried everything known to mankind, to get digital modes to work with R1CBU.

It was my understanding that R1CBU was just a different GUI, on top of the radio. It is NOT.

So at first I thought that flrig was at fault.

So I booted up the default rig, and changed wsjtx to use IC-705 and set it up for CAT control. It worked flawlessly (via ttyACM1). So, I knew that everything was working.

I rebooted into R1CBU v19. And I didn't use flrig either. So all I was using was the hamlib part of wsjtx. Same IC-705, same CAT control parameters. Nothing. So, I can only come up with the conclusion, that R1CBU doesn't work with digital modes.

Too bad, I wanted it to, so bad. I like the interface.

Jerry

----

Extra Ham Radio Operator: WF5W

Registered Linu=x User: 275424

3D CAD designer

The most exciting phrase to hear in science - the one that heralds new discoveries - is not "Eureka" but "That's funny...". - Isaac. Asimov

v19 no CAT control problems

#22

My cat control no longer works with v19 R1CBU.

I am running on linux mint:

My radio is at latest firmware revision (from Radioddity - the one that says "fix Cat")

1. I boot up as default x6100

dmesg says ttyACM0 and ttyACM1. I know that ttyACM1 is the cat control.

I go into flrig, and set my transceiver to ttyACM1 and 19200. Good to go. PTT works and CAT control works just fine.

I reboot after putting in v19 of R1CBU, go into flrig, and choose ttyACM1 and 19200. Nothing works, no matter how many times I try it. And I've tried 9600, 38400, and 115200. Nothing.

I boot back into default. Good to go.

Anyone have any ideas?

Jerry

----

Extra Ham Radio Operator: WF5W

Registered Linu=x User: 275424

3D CAD designer

The most exciting phrase to hear in science - the one that heralds new discoveries - is not "Eureka" but "That's funny...". - Isaac. Asimov

Re: ACC Control Problems

#21

Please close this issue. It was a ground loop problem. Pesky things those grounds! Gotta connect them in the proper places. Still not sure why RICBU firmware was more susceptible.

Re: v19 Feedback problem

[email protected]

#20

I too had the same problem with my x6100.

开云体育