开云体育

HI Colby, I was able to get another computer and set up the QnetGateway and here are the "ip a". The enp0s25 was connected from the router to the gateway and the enp4s0 was connected from controller

I don't see anything intrinsically wrong with what you are doing. I'll have to look over the gateway code to see what it does when you sever the TCP connection to QuadNet when you drive out of range

Hi Colby, I decided to just get another computer for the gateway. Thank you very much. i will start from beginning and will need your assistance. Thanks again.

That what make it special.? there's no monitor connection unless you add one to it but you could ssh into to it. Maybe look for a Youtube on it Will

QnetGateway is designed to run headless (i.e. no monitor) so long as the device will accept a modern Debian distribution it _should_ work but our testing was performed on the Raspberry Pi, it is aptly

Hi Will, Will this work the QnetGateway? I did not see any monitor connection.

If you need a another computer check out the EspressoBin SBC. (google is your friend)? It has 3 built in Ethernet ports? and can be use in different ways. Will / W4WWM

Something is going on because your 2nd hardware ethernet device is not registering on the system. eth0 is the pi’s primary onboard ethernet adapter and has an autoconfigured address which means it

Hi Colby, Yes and I just did an apt update. here is the ifcofig -a. eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 169.254.48.39 netmask 255.255.0.0 broadcast 169.254.255.255 inet6

Is your Pi able to access the internet, like you can do an apt update and it syncs its package cache with the raspberry pi repo and you can apt install packages that are downloaded over the internet?

Hi Colby, I took photos of my set up and configuration on the repeater (RP2C controller manual). I will send you the qn.cfg file.

Hi Colby, Here is the file qn.cfg. I do not know how to set up for the ssh. # Qnet Gateway Configuration ircddb = { login = "KM6VLB"; # login callsign for the ircDDB network host = "rr.openquad.net" #

That worked fine. Thank you. I just used it on my home wifi network for about 20 minutes, on REF001C and XRF757A I think I need to change how I operate, if I am understanding your comments. My normal

No problems, we’ll work through it. The trick to the whole set up is the static IP on the 2nd NIC that is plugged into the ICOM repeater controller. It will have to be configured manually and be set

Hi Colby, I am sorry if was not clear, this is my first time to set up an icom repeater (ID-RP4000V) with the controller (ID-RP2C).? I appreciate all the help I can get, I might be a little slow in

Whoops, sorry! Try it again.

git pull says “already Up-to-date” pi@raspberrypi:~/QnetGateway $ make clean rm -f DVAPDongle.o QnetVoice.o QnetGateway.o QnetRemote.o QnetRelay.o aprs.o QnetITAP.o Random.o QnetDVRPTR.o

Okay Carty, I think what was happening is that programs were starting before the tethered network (from your smart-phone) was ready. Thanks to some help from Colby W1BSB, I rewrote the *.service

I’m a bit confused myself. Is this on a Pi? Have you changed the repeater’s IP to an address on the same block your router and system are configured for? With QnetGateway, to link to a reflector,

Hi Colby, Thank you very much. I did what you provided and did not see any error but it would not link to where I configured to XRF072 A (Set up BXRF072A). I am a little bit confuse in setting up the