Hi Will,
Will this work the QnetGateway? I did not see any monitor
connection.
On 9/6/2018 6:03 PM, Will wrote:
toggle quoted message
Show quoted text
If you need a another computer check out the EspressoBin SBC.
(google is your friend)? It has 3 built in Ethernet ports? and
can be use in different ways.
Will / W4WWM
On 9/6/2018 6:10 PM, Nomis Bayan Jr.
wrote:
Hi Colby,
I am sorry if was not clear, this is my first time to set up
an icom repeater (ID-RP4000V) with the controller (ID-RP2C).?
I appreciate all the help I can get, I might be a little slow
in learning, please bear with me. Before I go any further,
please? let me know if my set up will work.
Using Raspberry Pi 3 and the second NIC was connected to the
USB, TP-Link. ID-RP2C 10 Base T connected to the PI 3 ethernet
connection and my router/modem connected to TP-link. Will this
work, if not them I will get another computer and start again.
On 9/6/2018 6:33 AM, Colby Ross
W1BSB wrote:
I¡¯m a
bit confused myself. Is this on a Pi? Have you changed
the repeater¡¯s IP to an address on the same block your
router and system are configured for?
With QnetGateway, to link to a reflector, you must put
XRF072AL in the UR field. It¡¯s a bit different than the
conventional ICOM stack.
?
The IPs
are configured in the qn.cfg file, you have to tell it
what IP your repeater is on and what IP the gateway
should be listening on.
?
Show me
the output of your /usr/local/etc/qn.cfg file, the
output of journalctl -u qngateway, and tell me what IP
your repeater is currently assigned, as well as your
router, and the system you are running QnetGateway on.
(The local IP addresses, i.e. 10.x.x.x, 192.168.x.x,
172.x.x.x, etc)
?
Colby
?
?
?
Hi Colby,
Thank you very much. I did what you provided and did not
see any error but it would not link to where I configured
to XRF072 A (Set up BXRF072A). I am a little bit confuse
in setting up the IP addresses and need assistance. I am
using and assigned a fixed IP address to the Gateway and
assigned it on my modem/router, the same set up I did on
the XLX server. I appreciate if you could assist me in
setting up our Gateway link to icom repeater. Thank you.
Questions:
1. QnetGateway/qn.icom.cfg: Do I need to change any IP
addresses on the qnet Gateway Configuration?
2. Icom ID-RP2C controller: following the ID-RP2C manual,
setting is currently Gateway IP address: 172.16.0.20 and
port is 2000; Communication Settings IP address:
172.16.0.1, Port 20319, Subnet 255.255.255.0, Def Gateway
0.0.0.0. Do I need to change any setting on the
controller?
3. Where do I enter the static IP address (purchased five
fixed IP address from AT&T)?
?
On 9/5/2018 9:20 PM, Colby Ross W1BSB
wrote:
Try sudo make uninstallicom and then
sudo make installicom
?
From: [email protected] <[email protected]>
On Behalf Of Nomis Bayan Jr.
Sent: Thursday, September 6, 2018 00:19
To: [email protected]
Subject: [QnetGateway] Gateway - Raspberry Pi 3
-need help
?
Results after running sudo make
installicom:
pi@raspberrypi:~/QnetGateway $ sudo make installicom
######### QnetGateway #########
/bin/cp -f qngateway /usr/local/bin
/bin/cp -f qnremote qnvoice
/usr/local/bin
/bin/ln -s
/home/pi/QnetGateway/qn.cfg /usr/local/etc
/bin/ln: failed to create symbolic
link '/usr/local/etc/qn.cfg': File exists
Makefile:139: recipe for target
'installicom' failed
make: *** [installicom] Error 1
pi@raspberrypi:~/QnetGateway $?
?
