开云体育

Yes, I'll see what I can do.

Hans or anyone else, I am testing out my Progrock with the pr1.01a.hex file. I cannot connect to it with 9600 Baud but works perfectly on the communication side with 1200 Baud. Has anyone seen

Steve K1RF, How critical is the resonant circuit C30 and L4 for single band performance? ?Are we looking at a broad bell shaped curve response or a sharp peak? ?I think I read somewhere Hans picked

...and, if you mail a check with the order, they ship free of charge to US/Canada.? See item "6 . Shipping CHarges" under part "II. COnditions of Order" at

Kurt while Hans said it was easy to remove L5, my went kaput also (not many days before your attempt) !? it my case it was mechanical stress.? I found a 25 uH inductor in my stash, made decades

Kurt, I like digikey.com. They stock modern parts, and will ship via USPS. My last order of mostly surface mount parts shipped for less than $4. I can always find stuff to add to my cart to help me

Al what is your signal look like with the 5 watt PA out of line. Is it possible to disco it and just run your U3S barefoot. I am no expert for sure but I have never seen a signal such as yours from

TaydaElectronics.com - they have a $5 minimum order requirement, but shipping is very cheap. Just get the bill up to $5, and chances are?that you will pay $1.50 or close to that in shipping. They

Greetings all; ? Well I was attempting to make the L5 inductor (100 micro Henry across pins 7 & 20)? mod when I apparently overheated it having it to fall apart... one of many boneheaded maneuvers

If you are trying to operate on both 30/40, the answer is likely that the output stage, which is a class E amplifier, needs to operate reasonably close to its optimum resonant frequency. The series

I also seem to remember some other folks getting low RF output because a toroid underneath the LCD screen would contact one of the tabs holding the screen in place. ?I bent the mounting tab flat

Good info.I bought it in UK, shipping time is short than Thailand. For EU country there are import tax+vat too from Thai (not for UK). Best regards Fabrizio Inviato dal mio dispositivo

Here's a comparison between two power supplies running FSKCW on my U3S (Single band, w/ 5W PA kit outputting 2W TPO). Top image is with a switching supply (Radio Shack 19A). Bottom image is with

For what it's worth, Tayda has the Hammond 1590BB painted for $6.99. <http://www.taydaelectronics.com/catalogsearch/result/?q=hammond> No affiliation or pecuniary interest, just trying to

Martin thanks very much. 73 IZ0HCC Fabrizio Inviato dal mio dispositivo Samsung -------- Messaggio originale -------- Da: Martin Waller <martin@...> Data: 13/12/2017 13:34

John Blackett, Yes, it's a switcher. I'll give it a try with a linear one and repost. 73. --Al

I built mine for 30m and had similar low power issues. I took 2 turns off the LPF inductors and now I get 3.5W on 30m and 4.8W on 40m on a 13.8V supply. It was about 2W on 30m and 3W on 40m before.

73 Enno, I too find the same as you. I don't know the answer. It sure works on both 30/40, which also is unexpected, after all I was trying to make mine work on 20/30 ! I would like to have higher

I hear this same sound when trying to listen above a certain frequency (from memory around 12 or 13 MHz) on my QCX which I built for 30m. It has something to do with the programming and quadrature --

Thanks Nick. I will check and respond later today. ? I suspect the toroids. At first they seem so simple but that coating can get ya if you are not thorough.? Barry