开云体育

Where is Han's troubleshooting guide?? There is alot of good info in the group if you search, but I didn't realize there was a single document that contained detailed? info. Andy

Can you test WSJT 2.6.1 and see if PTT works?? That will still have the TX/RX commands. Then only different I can tell is FLRig uses TQ and Hamlib was using

Hello Mike As far as I am aware the QDX still supports the standard TX; and RX; commands in the TS480 protocol. Nothing was removed. They are used by WSJT-X and JS8call for CAT Tx/Rx control. This

Will that DLL also work on a Pi? That's all I have to test with. 73, Cliff, AE5ZA

Hi all There hasn't been any change to the TX RX commands. And I'm using 1_08 with JS8call without issues. So I suspect you have some other problem... 73 Hans

This would make a great amp but unfortunately it does not cover the whole 10m band. Not a good idea to stop at 28,5 MHz. Robert, OE7OER Von: [email protected] <[email protected]> Im

Working on a U4B sensing and sending radiation levels via the U4B telemetry channels project. Let me know if anyone in our group is interested in working together on this interesting

Apparently TX/RX does not work anymore -- that's what Hamlib uses...FLRig is using the newer TQ1/TQ0. This 64-bit DLL has the change to TQ So give it a try.? It goes in the WSJT-X bin

Mike, I haven't looked at the code for the QDX in flrig, but the firmware manual for 1_06 and on has Tx and Rx as commands as well as the TQ. They should all work. 73, Cliff, AE5ZA

I see that QDX apparently wants the "TQ" command for PTT control. What compatibility mode is that and why can't it use "TX/RX" like the TS-480 compatibility it claims?? At this point it should

Joshua: You can shorten the URL considerably by just using the ID number (3256804580861697). (See below.) The same idea works on Amazon and eBay, too. Jack, W8TEE

Many thanks Joshua ! 73, Jamie WB4YDL Sent: Tuesday, January 24, 2023 10:02 AM To: [email protected] Subject: Re: [QRPLabs] QDX pairs nicely with the Micro PA50 James, Here is the link:

James, Here is the link: https://www.aliexpress.us/item/3256804580861697.html?spm=a2g0o.order_list.order_list_main.18.4dac18027y5r58&gatewayAdapt=glo2usa&_randl_shipto=US You can manually change the

Phill, Just a couple of things: - Get the newest flrig alpha from www.w1hkj.com/alpha/flrig. It has a fix in flrig that affected the audio quality with firmware over 1_05. - in Wsjtx select the rig

Well it didn't go quite as well as expected. FLRIG and FLDIGI worked using QDX as transceiver in FLRIG. WSJT-X and JTDX both receive fine but fail to turn on TX on the QDX. Looks like some

You might try using your 15MHz reference directly.? I know the '5351A isn't exactly specified for this (other devices in the family are though), but I send a 10MHz 3V-logic-level clock to the '5351A

Hi folks - Sharing this repair experience in case it helps others or if anyone has further advice to add. After a couple of days working fine on 20m and 40m my QDX stopped transmitting and battery

Hello Halden 30MHz was tried before. The Si5351A works but the spectral purity is greatly impaired. U3S would work too if you set the reference to 30MHz. But as I said if you put a spectrum analyzer

Not in my corner of the Internet, ‘only’ 8 of the plastic case, but lots of the aluminum. Both available Prime delivery Wednesday. You’re on your own for dense fog. ? 73, Willie N1JBJ

Hi Howard, thanks a lot for sharing, that looks very nice ans inspiring. Best 73, Fred, HB3XBA