开云体育

Thanks, Andy! I will clean it gently and see what it looks like after that. Pekka

The device is Texas NE5532P which is NIPDAU/SN (Nickel Paladium Gold over Tin) so it won't be corrosion but some kind of tarnish or foreign gunge. It's on the top of the pins not the bit that gets

Hi, I just started my QCX+ build today and got to installing ICs 5-10. On one of the NE5532P circuits pins have corrosion on one side (see attached photo). Normally I would just clean the pins but it

Thank you Steve. I appreciate the tip and hearing your experience. -- regards, Bryan, N0LUF

Mike, It was a typo. phpAdmin, a SQL utility to pull HAMlib records? --- that I DON'T need. Duh ! Hans had it correct, RTFB John

John, the way FLRIG is designed to work is that it connects to your radio, then all your other software looks at FLRIG as being your radio. In your example above, ?If JS8Call’s radio is something

Hi, here are modifications that I have made to the PCB ver. 3: - changed C71, 72, 73 and 74 into a SMD 0604 0R resistor (0 Ohm bridge) - removed unneeded R30, 35, 37 and 38 - added a 2u2 cer. kond to

Thanks for getting back Greg. Also, thanks for the feedback on the attenuator. I am getting the heartbeat and maidenhead with the GPS so I guess all is well. Quite impressive for sure. -- 73, Rick

Hi Terry, ?Thanks for the great feedback! I'll change the BS170s. ?Should I in fact change all four at once or can I mitigate potential rework damage and simply change one at a time and test? Or

Hi Rick, Those settings seem right to me. If you display the heartbeat signal on the LCD and you see it pulsing, I think you can be sure you are disciplining the frequency. This is the #HB special

The QLG2 arrived today and it is now installed in the QRP-Labs SigGen. However, I am confused? 1) The GPS red, yellow and green (1pps) LEDs are functioning as they should. 2) GPS Mode is set to *2

Peter, Been there-done that! - You popped one (or maybe two) of the BS170's - easy just to change all 4. Some folks have even installed sockets for the BS170's - Like "Smarties" always keep a supply

Ron, Thanks for your guidance. I'm glad you are here. 1.) Connections look good on T1. 2.) 10K resistors at R1 and R2? are marked accordingly. ( the radio has been working close to a year now so no

OK. Figured it out. Going through the menus I noticed that the Ref Freq was reset to 27 MHz with the new update chip. I installed a TCXO some time ago, so upon changing the freq to 25 MHz, SWRs went

Well, I guess I spoke too soon! ?VE3EGA, so much for maintaining status quo... (and you should buy a lottery ticket - you called it...) Since repairing my QDX 24 hours ago (and making 20 FT-8

I am using a Orange PI 800 which is a Chinese clone of the Raspberry PI 400 with the QDX.? The Raspberry PI 400 was not available to me.?? I followed the instructions in QDX manual and the work

I think I'm missing something. This behavior is so bizarre: Purchased 1.09a chip from Hans and inserted into 40m mini. 5 watts out with 1.0:1 SWR into a dummy load. All good! Then tested on my dipole

Hi Guys A reminder... Some of you are making it more complicated than it needs to be. Some others are going where no man has gone before. Which is fine too. But it's worth remembering that how to use

John, It's only in the alpha builds. www.w1hkj.conm/alpha/flrig <http://www.w1hkj.conm/alpha/flrig>. You'll have to compile it yourself. To do that for any of the flxxx apps go here and follow the

Hi Joe How many balloons do you intend to launch at the same time with the same call sign.? Technically it is possible with the QRP-LABS tracking website, as long as the channel number is different,