开云体育

Works fine as well. I didn't realize it was there, but no issues. Just had a QSO using it. 73, Cliff, AE5ZA

What about when the QRP QCX/QDX is selected?? It's there in 2.6.1 Mike W9MDB

I managed to incorrectly two of the windings on my QCX (40m) T1 and have had to remove it. I only have .25mm magnet wire. Will this be OK or do I need to order .3?? Many thanks Sam 2e1oct Samantha J

Hi Gerry If nobody else can help out... I do have something like 10 built original QCX boards in unknown operational state and I could try and find a working one. 73 Hans G0UPL http://qrp-labs.com

Not I, Mike I'm out-of-lab until 06-Feb. 73 Hans G0UPL http://qrp-labs.com https://www.buymeacoffee.com/g0upl

Hi. I am looking for an original QCX CLASSIC case if anyone in the UK has one they are not using. Regards Gerry G4OJF

Go to the QRP Labs website and select the QDX. The the left hand column under QDX you'll see a link to the troubleshooting guide. 73, Cliff, AE5ZA

Mike, Both Wsjtx 2.5.4 and 2.6.1 work fine with the TS-480 rig selected for the QDX. Apparently the TX/RX works. This is with firmware 1_08a. At first I thought the red bar for PTT test indicated

As a workaround why not just configure WSJT to use FLRig as a “transceiver” rather than using Hamlib?

Where is Han's troubleshooting guide?? There is alot of good info in the group if you search, but I didn't realize there was a single document that contained detailed? info. Andy

Can you test WSJT 2.6.1 and see if PTT works?? That will still have the TX/RX commands. Then only different I can tell is FLRig uses TQ and Hamlib was using TX/RX

Hello Mike As far as I am aware the QDX still supports the standard TX; and RX; commands in the TS480 protocol. Nothing was removed. They are used by WSJT-X and JS8call for CAT Tx/Rx control. This

Will that DLL also work on a Pi? That's all I have to test with. 73, Cliff, AE5ZA

Hi all There hasn't been any change to the TX RX commands. And I'm using 1_08 with JS8call without issues. So I suspect you have some other problem... 73 Hans G0UPL http://qrp-labs.com

This would make a great amp but unfortunately it does not cover the whole 10m band. Not a good idea to stop at 28,5 MHz. Robert, OE7OER Von: [email protected] <[email protected]> Im Auftrag von Joshua

Working on a U4B sensing and sending radiation levels via the U4B telemetry channels project. Let me know if anyone in our group is interested in working together on this interesting project. Thanks!

Apparently TX/RX does not work anymore -- that's what Hamlib uses...FLRig is using the newer TQ1/TQ0. This 64-bit DLL has the change to TQ So give it a try.? It goes in the WSJT-X bin directory.

Mike, I haven't looked at the code for the QDX in flrig, but the firmware manual for 1_06 and on has Tx and Rx as commands as well as the TQ. They should all work. 73, Cliff, AE5ZA

I see that QDX apparently wants the "TQ" command for PTT control. What compatibility mode is that and why can't it use "TX/RX" like the TS-480 compatibility it claims?? At this point it should

Joshua: You can shorten the URL considerably by just using the ID number (3256804580861697). (See below.) The same idea works on Amazon and eBay, too. Jack, W8TEE