开云体育

Hello Brian, may I send you my bank account number to get money to by all the new stuff to use for field operation? 73 Ludwig

I use FT8CN in POTA for activations (Android). Calling CQ works well. Searching, e.g., for P2P QSOs, is more difficult with the limited screen. The configuration settings are sufficiently commented

I would not spend any time making changes to support end of life or soon to be end of life operating systems.

Hi Stan … I had set my polling to 10sec as Hans had suggested. Thanks for your input. Dick, K5AND Sent: Thursday, April 24, 2025 1:34 AM To: [email protected] Subject: Re: [QRPLabs] qmx

Good morning, Hans … I am using Windows 11, 64 bit. Only WSJT is connected and other two ports unused. The system plays nicely for a short time and then drops the ports. After turning radio

On 4/23/25 I had a CW practice / rag chew session on 20 meters. I worked two stations: Conditions were OK. SSN = 142, SFI = 163, A = 12, K = 1. Early on I heard a couple of weak stations calling

I'll have a look at adding additional CAT commands to FLRIG in my next play-time :-) Great to have the multiple terminals - FLRIG shown doing its stuff with the terminal monitoring CAT commands. As

Thanks for the reply. I have enough cores to stop and stray RF I will try that. I have reread the manual and see that the power I referred to is ‘tx status’ and I will make the changes you

Excellent work Hans, I applied my hack on udev to get the new ports consistent, and now my machine shows: /dev/QMX00 -> ttyACM0 /dev/QMX02 -> ttyACM1 /dev/QMX08 -> ttyACM2 So I can now use a

Hi Dick and Richard, You reported COM ports got dropped in the new firmware - I have not seen any problems. But I am using Linux. It would be very helpful if you can provide more details. What is

I have just been operating FT8 with lots of contacts on 40m for over an hour now, with no com port problems.? For the last half-hour, I also connected to the QMX terminal and started the "Input

The power meter should "pulse" on with every dot and dash, and will go off between them at lower CW speeds. This can be controlled with the "Tx->Rx hang time" setting for the "Pwr/SWR display". The

You can use the terminal menu to set the mode with a CAT command: open "PC and CAT", then "CAT command test", then type the MDx command to set the mode x = 1 for LSB, 2 for USB, 3 for CW, and 6 for

See this post he made a few months ago with his contact info: /g/QRPLabs/message/137552

Yes, those look ok, not too different from mine. For the 6m and 15m LPFs, you may want to spread the windings on the toroids to move the filter rolloff a little to the right, which may give a little

Need to get in touch with Jeffery Moore to get my factorey built new qmx+ which will not transmit repaired.? A Phone number or email would be helpful. Thanks? Steve N1SG

Hans- As always, great work and amazing results. The multiple virtual COM port discovery and development is quite intriguing - can I make a suggestion/recommendation? I have a QMX+ with the GPS

Thanks for this Stan. You saved me a ton of time when I tested WinLink. It worked first try! Side effect of using VARA HF is that it leaves the QMX in SSB mode. When I go back into WSJT-X it doesn't

Keep in mind that ANY RF detection T/R switching scheme is going to unavoidably hot-switch the transmitter while it is putting out power. Best to use wired switching if possible.? The '818 has a TX

Hi, The driver support for Windows 7,? and Windows 10 and 11, is different. Check the internet for work arounds or perhaps YouTube. There were drivers available for my Windows 7, but I never got