开云体育

Welcome to the annual beg-a-thon for funding our space on 开云体育! The yearly cost is $220 USD. Every year we've gotten more than enough from members to pay that bill... and usually a little surplus. The surplus from last year is $28.73. So a few of you very kind folks kind of jumped the queue and already sent me money... right now we are at a total of $149.39, including last year's surplus. So there's another ~$70 to go. Thanks, -Scott -- ---- Scott Helmke ---- scott@... ---- (734) 604-9340 ---- "I have ceased distinguishing between the religious and the secular, for everything is holy" - Joe Henry

Hey, it's that time of year again! I'm out of town for a couple more days, so I don't have access to my usual pitch and all that stuff. But basically the group costs a couple hundred dollars a year to run, and usually it's paid for by donations. So it's on your radar now... when I get home I'll look up the amount, see if there's any surplus from last year, and all that stuff. As always thanks, not just for the support but for the fantastic content we have on this group. Thanks, -Scott -- ---- Scott Helmke ---- scott@... ---- (734) 604-9340 ---- "I have ceased distinguishing between the religious and the secular, for everything is holy" - Joe Henry

I hope this is OK to ask here as it isn't exclusively a mic question but a general electronic question that might be applicable to some mics. Consider a fet input with a high impedance, that is connected to a exposed bare wire or RCA type plug, because it needs to be unplugged from the source. This could be for a piezo pickup with an input impedance of 5-10M or it could be for a condenser mic with an impedance of 1G Do I need to protect that bare fet gate from ESD it might encounter in the world? here's a schem to illustrate: https://halfshavedyaks.xyz/forumimages/fetbuffersm.png I have naively added diodes but I'm not sure if they will actually lower the input impedance which obv I don't want. The real-life behaviour of diodes at high impedances is beyond my current level of understanding. I'm also not sure if 1N4148 are big enough to offer much protection. Nor am I sure if R1 offers any protection. Could any of the experts here talk me through what would be wrong with the attempts at ESD protection in this schematic?

Two decades ago I was an active DIYer and built a couple binaural heads, some PZMs, and other projects. About the time Panasonic was discontinuing the WMxx (61? See, it's been that long), I ordered a bunch of capsules to play with, I think from JMI, but it might have been a group buy that Bob Cain put together. Now I have a use for a 9mm electret capsule, and I've got this package with some TS-94A capsules, and also some TSB-9445A and TS-52B. What I don't have (at least not on any hard drives I have spinning, or useful results from that once search engine, now ad flyer Google) are spec sheets for those capsules. I remember enough to put together a 9v battery, a ??K resistor, and a DC blocking cap, but I'd like to get the resistor value close on the 1st try. Does anyone have spec sheets for this old Transsound capsules, or a link to them? Thanks much, Mike

Has anyone here tried either of these dynamic mics from AliExpress? Fifine K669D Maono PD100 They look like solid bodies, I'm curious if they come apart easily and how good they would be as donor bodies. https://www.aliexpress.com/item/1005005510482582.html https://www.aliexpress.com/item/1005004887926822.html

Pondering how to choose SimpleP48 resistors, it suddenly occurred to me that we can use the techniques in FETbias.doc so I've updated that in my Files/Ricardo directory. It's so obvious with hindsight that I beg yus guy's pardon for my stupidity. Measuring at 9V is perfect cos we want 5 - 10V Mea culpa, mea culpa, mea maxima culpa.

I’ve been looking around to try to find some sources of material to enable me to learn about how amplifiers work. I’ve only got the most rudimentary electronics knowledge so end up floundering very quickly. I bought The Art of Electronics a while ago and have had a cursory browse through it. I was also recommended this paper by an old work colleague. https://1drv.ms/b/s!Ap5IR9dQ9eMPgfxAOWdiIkU-1cGvcQ "Audio power amplifier design" has also been recommended to me. What do you guys think / recommend to enable learning about these things? It seems that a lot of you are well versed in the ways of coercing electrons

Is there a way to connect a 3 pad electret (ground/source/drain) to the Linkwitz 2 wire solution? Thank you!

Hi all, a new ultrasonic microphone is now available on: https://www.dodotronic.com/product/ultramic-384k-evo High sensitivity and double MEMS sensor Cheers Ivano Pelicella

(First post) Hi, I have been experimenting with small electret microphones (from Primo) mounted on goosenecks as violin pickups for busking (including classical repertoire). Visibly similar to a DPA 4099 but orders of magnitude cheaper.... Results are quite good: not as nice as my external SDC in the optimal position (and probably not as nice as the DPA!) but way better than any piezo I've tried. I'm considering a next version with a slightly larger, FET-less capsule and an Alice circuit. The circuit would likely be too big to fit immediately next to the capsule, so would be distanced by around 15-20cm (6-8"). I am wondering how this separation of capsule and preamp would impact performance (e.g. noise, stability). Would it be better to stretch Alice by putting the 1G resistor and first FET with the capsule and the rest of the circuit downstream? I've seen the discussion on FET availability and the resulting OPA Alice. Are the 2N4416 and 2N 5087 still available (September 2024)? Would it be better to switch to an OPA circuit after the initial FET? For this application, it's a balance of sound quality (trying to amplify a good quality violin), directivity (to minimise feedback from amplifier), and practicalities (not getting in the way of the violin bow). Thanks for any comments! Jeremy

I have several 25mm Chinese electret capsules without internal FETs. How do I add a FET to one to make it like the TSB2590A?? And can I use any FET to do it ? Also , In another topic I see an SMD circuit board being used. Are these available from PCBWAY or are they not commercially available?? Thanks.... Charles

I'm thinking about maybe making a mic with 3 capsules to use as a stereo mic for recording instruments in my home studio. So a sort of flexible 2D stereo image mic, rather than a 3D soundfield. I don't need full soundfield, as the room is not so good that I often want much of the back, top or underneath of the mic. Mounting a full tetrahedral setup seems like overkill for my likely use. But I'm thinking of maybe front + left + right cardioid capsules, with a circuit to provide three outputs, which could then be combined in the daw to offer M/S or XY (at 45 degrees) or various form of mono multipattern. I'm interested in suggestions for how the capsules should be placed. If they are cardioid capsules they'll need some air space around them. Should they be in a vertical line? or with the front capsule in front in a triangle? Also suggestions for which inexpensive capsule would be most suitable. TSB2555 springs to mind but I'm not sure about the offaxis response, and maybe a smaller capsule would be better. any suggestions?