开云体育

Thanks Art, Youre the greatest. Claude 100

John: Leave it off unless you have severe rounding. It is unused in 99.9% of systems. Thanks, Art www.artofcnc.ca Videos And Support Forums http://www.machsupport.com Users Map:

Hi, New here. Just finished my machine yesterday. I'm very proud of my baby: it is rock steady, pretty fast and can mill 125x70x50 cm. It is a router style machine with a gantry. For me this means

--- In mach1mach2cnc@..., "vrsculptor" <vrsculptor@h...> wrote: I need to upgrade the control on my 1981 Tiger / Sharnoa mill. It has a 2hp head, X 30" Y -17" and Z -5.5". I like what

--- In mach1mach2cnc@..., "vrsculptor" <vrsculptor@h...> wrote: I need to upgrade the control on my 1981 Tiger / Sharnoa mill. It has a 2hp head, X 30" Y -17" and Z -5.5". I like what

I searched through the messages & files to find a setup file (.xml) for the MAXNC CL. Apparently files were send to private e-mails. Can all MAXNC - Mach3 users send or put their setup files in the

Hi: The changes are at Toms request, so I think while it may change thigns a bit, the changes will be for the better.. Thanks, Art www.artofcnc.ca Videos And Support Forums

Hi Chris: Macro call SingleVerify( axis ) Thanks, Art www.artofcnc.ca Videos And Support Forums http://www.machsupport.com Users Map: http://www.frappr.com/machsupport

In mach3 what does angular limit cv mean. There are 2 values here and I am not sure how to define them? Thanks, John

Hi, Does anyone (like Art) know if it is possible to verify a single axis at the time. I am modifying screen macro, and need to do this, both, silently AND otherwise. Thanks, Chris K.

Arthur Eunson wrote: Arthur No not really, although DC drives do give pretty good torque, I have seen so many blow up and they are more expensive than a good VFD and 3ph motor. In fact one of my

Hi Tim: Can be a lot of reasons for that one. I take it your in CV mode, enhanced pulsing is selected? Send me the code if you like, Ill see if its coarse as a generated

Peter: Yes, the number is from 1-100% of feed speed. SO setting 1% will antidive at 1% of the requested feedrate. Do you also have the antidive turned on? Is the antidive LED

before the toolholder hits the table.all you lose is an endmill

I am working on a 4 axis machine and am wondering if Mach3 needs a high speed computer to move all 4 axes simultaneously at slow speed. I am currently planning on using a 750mHz CPU. Thanks, Keith

I am using the THC300. When the machine slows down into the corners the torch will crash, ie dive lower as the thc gives a different voltage reading. So in the anti-dive box I can only enter a value

Hi Ben, Check the very common Gecko Drives (www.geckodrive.com) most of people use them for convert. Shadi

I have a 3d file of basicly a 2 1/2" dia dome.I can't get the feedrate hardly above 5ipm. When I increase the feedrate higher, the motion is very rough. My configuration is .200 pitch on the ball

Hi Eric: Not sure abouy the first, Id have ot see the code, the second is easy, use the Config/IJ mode to switch to IJ Inc. This usually fixes that one.. Thanks, Art www.artofcnc.ca Videos And

I'm not sure if I have a config problem with Mach3 or my post processor, but I'm sure this is the place to find out ;-). There is a pretty simple file under files here on the forum called Test