开云体育

I haven't played with this and can't say specific for Conky but to parse the data you could use: *bluetoothctl info 98:D3:31:F7:55:37 | grep Connected* which should just show you the connected

No need to delete as it never installed to begin with. Please post other questions in a new thread so we don't derail this topic. -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar (

Hi I assume you are answering my post. But I didn't have any trouble with wifi, only the display showing funny. I think though I would like to get a copy of that distro to try. What I would like is to

Ah, forgot about that one. It is very stripped out. It would be better to just run the real Debian Buster (10) or Bullseye (11), and have easier access to the full tools and drivers, unless there is a

I think you misunderstood the OS he is using. It is one I use on my HP laptop. It is an OS labeled for I386 I think on the Rpi site. I have most everything working on my i386 64 system. I am seeing an

Debian Raspbian runs on ARM processor. Your HP has an AMD Athlon 64 processor. Which Debian (or it's install instructions) did you use?

I need some expert help. I have been attempting to play with Raspberry. Have a Rpi 4 and everything great so far. Recently I have installed Debian Raspberry on my old HP Pavilion zv6270us. Install was

Hello all,?I recently purchased the Lab599 TX500 qrp rig last week (GREAT rig btw).? As its a new rig, it wasn't listed in FLRig but I did find that using the Kenwood TS2000 as the rig makes all the

This is way low on the priority, but has anyone figured a way to show connection status of Bluetooth adapter on a rig on the Conky? I am running a DRAWS Hat with BAP 3.0.8 and finally have almost

I would install nmap on the Pi that doesn’t have the GPS Then run it against the Pi you want to stream from. B ased on what you put in your OP: You will see something like this: $ nmap 192.168.0.200

Everything is working great now. I found this in the forums and ran these steps. (1) pkill -9 conky (2) conky (3) sudo apt install ruby (4) sudo gem install maidenhead (5) sudo gem install gpsd_client

Question. Must i delete hamlib4.3 if then how do i delete it. ? i assume that qsstv still grabs it as it did work until i update last week with BAP please advice De v51pj pieter jacobs

Ok done it as instructed rigcntrl is going green now when started but i get a error - unable to get freq from rig dial. Tcp 127.0.0.1:4532. Connection refused starting http service 0.0.0.0:8080 Config

Don thanks for the reply.? I found the problem Direwolf was not starting correctly. 73 Jeff KO4NCC

Thanks a million. Busy following instructions de v51pj pieter jacobs

There is an issue ( https://github.com/km4ack/pi-build/issues/296 ) that was reported with the latest version of hamlib. The fix has been posted here ( /g/KM4ACK-Pi/message/5509 )

Rich, KB3YBE, reported that hamlib 4.3 will not compile on the Pi. There is a missing dependency (libusb-1.0) The most current version of libusb on the pi is 1.0.22 but hamlib 4.3 needs 1.0.23 to

I don't know of anyone trying this approach. -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar ( https://www.paypal.me/km4ack ) Twitter ( https://twitter.com/km4ack ) | Store (

> > I apologize if I'm just not getting it and I've searched and searched and > watched a few videos and get stuck at the same place. > > I have BAP 3.0.8 > SignaLink connected > GPS Connected > When

Joseph, its a very flexible and informative device in a well-designed small package.? So far, its a keeper!? Jason's video was very helpful and informative.