|
Re: Packaging progres-
Very nice! Have you uploaded the stl files anywhere by chance? Brian On Wed, May 1, 2019 at 1:23 PM Robert Ogburn <ogburnrobert2@...> wrote: Using 3D printing for front plate.? Shown here are the assembled panel parts in both the CURA (3D CAD/CAM) program and a print in progress.? Several cumulative dimensional errors, none exceeding 3 mm.? Back to the drawing board.? PS- the panel was printed as two parts because as a single item it exceeded my print volume. Brian
--
Brian - N8BDB |
|
Packaging progres-
Using 3D printing for front plate.? Shown here are the assembled panel parts in both the CURA (3D CAD/CAM) program and a print in progress.? Several cumulative dimensional errors, none exceeding 3 mm.? Back to the drawing board.? PS- the panel was printed as two parts because as a single item it exceeded my print volume.
|
|
JackAl Display Protection
All: Al has made the Gerber files for his RA8875 display protection board available to all who might be interested. The Gerber files and a documentation file are in the attached zip file. I will also post these in the Files section of the JackAl group. The circuit is sufficiently simple it can also be constructed from perf board. This is the BOM for the PCB, which uses SMD parts. Components are as follows:
Jack, W8TEE |
|
Re: touch screen not working
Here's the 96 hex file: Jack, W8TEE
On Saturday, April 27, 2019, 9:09:19 AM PDT, f1apy - Jacques <f1apy@...> wrote:
Hello Jack, ? ¡¤???????? I checked wiring, ¡¤???????? upgraded my version of Arduino in 1.8.8, ¡¤???????? set up the recommended tree, ¡¤???????? the compilation works with some alarms ( pragma), ¡¤???????? I download the file Hex to teensy, ¡¤???????? it starts without problems, ¡¤???????? I use a screen 7 "it turns on correctly, ¡¤???????? I get the home page with version number 0.96, then the order page after 5 seconds. ¡¤???????? I can change the frequency with both encoders without problems. ¡¤???????? But when I want to enter the menu or change something on the screen, it does not work, I try to press (gently) on the touch screen, nothing happens .... ¡¤???????? By acquired consciousness, I tried a new screen (received yesterday from buy-Display) the problem is the same: - ((( ? From: [email protected] [mailto:[email protected]] On Behalf Of k7da
Sent: Saturday, April 27, 2019 4:10 AM To: [email protected] Subject: [JackAl] touch screen not working ? Jack checked the wiring according to what i understand the diagram says.? checks ok do you have the magic decoder ring that will tell you what each wire does?? may i be entrusted with that information. dave k7da ? On 4/22/2019 5:49 AM, jjpurdum via Groups.Io wrote: Different lines are used for the touch screen. This allows you to use the display w/wo touch. Check your wiring to the display. I'll pass this to Al to see if he has any ideas. ? Jack, W8TEE ? On Monday, April 22, 2019, 12:49:39 AM EDT, k7da <k7da@...> wrote: ? ? ? Jack ? does the touchscreen use the same data path as the viewing screen?? i ask because i get no response when trying to do the calibration routine.? is it possible to see the data somewhere in the radio? ? the calibration prints yellow lettering and a very small dot in the upper left corner but does nothing when pressing the screen for a while.? (10 seconds) ? what is necessary to get the print routine to print? ? debug was defined in the jackal.h and the serial monitor in the compiler turned on but there is no data printed.? i would think that with debug defined i should get something on the monitor as soon as the radio reboots after loading the program ? ? ? |
|
Re: 7 inch Display Destroyed $50.00 brick
There are several ways to do this, from one person serving as a clearing house and selling the boards for cost plus a small handling cost, to simply making the Gerbers available, which we will do. The other option is up in the air. Jack, W8TEE
On Thursday, April 25, 2019, 1:21:27 PM EDT, Brian Bowling <bowlingb@...> wrote:
I would like them as well. Maybe we should consider getting a group buy together rather than everyone ordering boards separately?? Good for thought.? Brian N8BDB On Thu, Apr 25, 2019 at 12:27 PM Vince Loschiavo <vince320@...> wrote: would like the gerbers for the board..I can get some made. Brian
--
Brian - N8BDB |
|
Re: JackAl Display and Voltage Spikes
All: Al is waiting for parts to test the PCB's we had made. We expect the parts any time. We'll then build and test one using the PCB and will release the board and the Gerbers when we're sure it's right. Jack
On Thursday, April 25, 2019, 2:47:54 PM EDT, Mark Hatch <mark2382@...> wrote:
Jack, Are the boards available yet? Address on QRZ? 73 Mark AJ6CU |
|
Re: JackAl Display and Voltage Spikes
Not sure what you mean by the second sentence. Jack, W8TEE
On Thursday, April 25, 2019, 12:26:02 PM EDT, Vince Loschiavo <vince320@...> wrote:
It should be worth it once the bugs are down to a minimum.. there are alot of uBITX kits out there... I still have the 49er..pieces ready to get going as well..with the article in QST doing the same for this one (but not until there are more than a few successes should help with recouping your time invested..(which for me has been invaluable).. Vince N2AIE |
|
Re: 7 inch Display Destroyed $50.00 brick
I would like them as well. Maybe we should consider getting a group buy together rather than everyone ordering boards separately?? Good for thought.? Brian N8BDB On Thu, Apr 25, 2019 at 12:27 PM Vince Loschiavo <vince320@...> wrote: would like the gerbers for the board..I can get some made. Brian
--
Brian - N8BDB |
Robert Ogburn
Brian Bowling
jjpurdum