开云体育

10-4. That’s a perfect place to start… Remember to check out uBITx.net too… Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big

Yes.? I see the documentation.? Since there appears to be little activity on the group and I just recently discovered it I was asking about what was the most recent. It sounds like it improved the

Oh I forgot! The best part was that the JackAl had/ has a very nice real AGC… not a AVC like more cheaper radios tout as AGC. Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ

So….. by chance…. have you checked the files section of this forum? Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch

The four states qrp group ran their first batch. Who knows if or when there will be another. Sounds interesting but I don’t really have the time. Just so I understand, how does the Jack ai board

You can short out the antenna jack or leave the antenna off and transmit too… doesn’t phase it. It’s completely bullet proof for guys like me that makes a mistake once in a while (more as I get

:) Now that’s what I call “rock solid”! [email protected]> wrote:

John: FWIT, both Al and I are using Bill's 20W PA for our own personal T41 builds. You can fire up the T41, set it to CW mode, put a brick on the key, go on vacation for two weeks, come back and it

I’ll try… Does it improve the raduino performance… not really… it improves the user interface for sure. The raduino is really just a square wave generator with a basic interface so I

Thanks. I get the idea. I appreciate all you have accomplished with this. I have been following the Software Controlled Ham Radio Group occasionally. 73s John N4HNO

The JackAl did have better performance, but not enough. Some of your comments sound like you are referring to the T41-EP rig we designed. You can read more about it at Amazon B0D25FV48C It is a 20W

Can you explain? What exactly does it provide? What shortcomings? Does it improve the raduino performance? The ubitx is a basic transceiver. I’m not expecting commercial performance but does it

I know what it does. I was part of the prototype group to test it. I still have one on one of my uBITx machines. It has its issues and its not the JackAl that has the problems. Dr. William

I am aware of that project. That is a bigger commitment than I have time for now. I was an electronics tech for years before getting into networking. I operate some qrp cw now and then. Some qrp

I have a ubitx v6. So this board adds better screen performance and some filtering and cw decode? Is this with the original screen and doesn’t require a Nextion?

You might consider stepping up to the T41 instead… Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch – K9ZC Staunton,

All of the parts are on the board and it's the same board QRP Guys used to sell. To tell you the truth, I would not buy the board. Support is spotty and the web site is not at all active. Also, it's

What displays are supported? Are the surface mount parts installed? I really don’t know much about the board except processor change and improved performance. John

Hi John: Most people seem to have lost interest. I still have a few populated boards if you want one. The cost is $35 plus shipping. Let me know if you're interested. Jack, W8TEE

I guess the initial run of boards will not be repeated. I didn’t hear about them in time. 73 John N4HNO