|
Locked
SX-17 Meter Damage
To all those who have provided leads for meter repair, I thank you. I am
following up on those leads. To the others who posted and were probably shaking their respective heads in disbelief that I was working on the SX-17 while powered up, I have this to say. First, if you are not familiar with the SX-17 chassis layout, other than the "S" meter terminals, there are no other live terminals or exposed wiring when working from the top of the chassis. So, I felt I was perfectly safe with what I was doing. I also had the mind set that I am working on a tough boat anchor with no real possibility of damaging anything. I mean after all, this thing weighs about 50 lbs. This I admit proved to be wrong. The one item that could be damaged was. Murphy is involved here. Second, the steel cover that goes over the main tuning capacitor must be removed to perform alignment and calibration. It allows access to the trimmer pads. In order to check the effect of the alignment with the cover on vs the cover off, I needed to have the receiver on and warm to avoid initial drift from cold start. So, the rest is history. The end of the shield cover hit the meter terminal and probably opened the coil. This "S" meter is in the plate circuit of the meter tube. So, basically, I shorted B+ to ground through the meter. Live and learn, but I will repair this receiver, count on it. Bill K2WH |
|
Locked
SX-17 Receiver, I'm Heart Broken.
开云体育Well just as I was buttoning up my SX-17, new looking, aligned perfectly, tuned up and receiving fabulously, I accidentally touched the "S" meter terminal with the metal cover over the main tuning cap. ? I BLEW OUT THE METER!!!!!!!!!!!!!!!? Can you hear me sobbing here as I write this? ? Anyway, I am looking for a replacement meter.? It looks like the SX-16, SX-17 and SX-18 had the same meter.? Anyone got one?? Contact me off list at K2WH@.... ?The members of this list, as Hallicrafters enthusiasts, you really don't want to see this wonderful almost NEW IN THE BOX receiver have this gapping hole in the front panel.? Do you?? I didn't think so.? So, sell me a meter. ? Thanks for listening.? Now I will go drown my sorrows.
? ?
? |
|
Locked
Electronic Supplier Bookmark
I have added my bookmark for Electronic Suppliers that can supply just
about everything you would need to restore and old radio. Just click on the bookmark and a list will come up. It is my exact list from my computer that I have used in my restoration efforts. Bill K2WH |
|
Locked
RG-62 Coax
I think someone asked me where I got the RG-62 coax for the SX-117
jumpers well this is where I got it: K2WH |
|
Locked
Re: SX-117 Video in Files Section
It's in the "Files" section.
toggle quoted message
Show quoted text
K2WH --- In HallicraftersRadios@..., w4awm@a... wrote:
where did you upload it to? |
|
Locked
SX-117 vs SX-17
BTW, I am not dropping a number in my "On Base and Warming Up" line
saying a video will be upcoming for the SX-17. It will be the SX-17. The one just uploaded is the SX-117. K2WH |
|
Locked
SX-117 Video in Files Section
I just uploaded a short grainy video of my almost complete SX-117.
Take a look at it if you feel like it. I'll leave it there for a little while. K2WH |
|
Locked
SX-117 "S" Meter Circuit and Changing "S" Meter Indications with Selectivity
开云体育The continuing story of the SX-117 "S" meter, and how it changes with different selectivity settings.? This is why it changes. ? I measured the AVC voltage on tube V7, pin # 1.? The following are my findings with an "S5" received signal: ? Selectivity Control???????? AVC Voltage on Pin # 1 ? 5 khz??????????????????????? - 0.84 vdc 2.5 khz????????????????????? - 1.09 vdc 5.0 khz????????????????????? - 1.37 vdc ? V7 is a 6DC6 tube and is used as a 1650 khz amplifier of which the "S" meter is in the cathode circuit. ? Tube V10b, is the 6BN8 tube or AVC rectifier which is connected directly to the selectivity switch. ?The selectivity switch switches in (2) different resistive values including (2) different capacitor values in the 2nd IF circuit.? These (2) added components to the 2nd IF circuit, provide the 2.5 and .5 receiver bandwidths. ? The resistive values are also connected to the 6BN8 AVC rectifier cathode circuit and the 2nd IF, thereby loading or unloading the AVC line which explains the varying "S" meter readings when the selectivity Control is changed.? I hope I got that right. ? K2WH ? ? |
|
Locked
WW2LST Recording
I have uploaded a recording of the LST boat with the call WW2LST in
the "Files" section. It was received on a Hallicrafter SX-111. The boat was off the coast of Georgia about 150 miles out to sea. The recording is 5mb long so if you do not have broadband, it may take a while to upload. I will leave the file for a while on the site. K2WH |
|
Locked
New Link Added for Knobs
Along with the PDF file on Mouser Electronics, I have added to the
links section, Ocean State Electronics page about knobs. While I have not purchased knobs for Hallicrafters here, I did purchase a complete set of knobs for an old Swan 700cx that were very close to original. My advice is to carefully measure your original knobs and compare to the ones offered by Mouser or Ocean State. Good luck. K2WH |
|
Locked
Apparently the entire Catalog is There
I just went to the Mouser files and at the top and bottom of each page,
you can click "Next" or "Back" and page through the catalog, maybe the entire catalog. Interesting the way this stuff works even though I uploaded just (2) pages K2WH |
|
Locked
Mouser PDF Files - Knobs
I have added (2) PDF files in the "Files" section. These are the (2)
pages of knobs offered by Mouser. Some of the knobs look to be close replacments for Hallicrafters, Swan and Hammarlund. K2WH |
|
Locked
Re: wanting sx 99 knobs
Try page 1235 and items 450-1170 and 450-1171. Both look close to the
Hallicrafters knobs on the SX-99 |
|
Locked
Re: wanting sx 99 knobs
In addition, try this page in Mouser Electronics Catalog or website,
www.mouser.com/eagleplasticdevices K2WH --- In HallicraftersRadios@..., Bill Gerhold <k2wh@o...> wrote: Look further down the messages here. I think this was alreadydiscussed. As an alternative, try this site.close. make them complete. any body got some spares at a reasonable cost or ais going to be a realy succesful group..Garyadvice, technical and general information about Hallicrafters transmitters,number of fans, cheerleaders and users of this wonderful equipment whichutilized the technology of vacuum tubes.the early years with military communications radios. On the home front withshortwave receivers, amateur transmitters and home entertainment equipment.Truly an American company.subject=Unsubscribe>
|
|
Locked
Re: wanting sx 99 knobs
开云体育Look further down the messages here.? I think this was already discussed.? As an alternative, try this site. ?
? They have lots of replacement knobs and you might find some very close. ? K2WH ? ? From: HallicraftersRadios@... [mailto:HallicraftersRadios@...] On Behalf Of Gary
Sent: Monday, May 23, 2005 5:42 AM To: HallicraftersRadios@... Subject: [HallicraftersRadios] wanting sx 99 knobs ? i am curently trying to restore a couple of sx99's? and they have |
Bill (Group Owner)