开云体育

Not that difficult, Keith. See: https://www.tubesandmore.com/products/plug-8-pin-octal-tube-base-black-plastic 73, Jacques, VE2JFE in Montreal If a DC power plug is not available for the back of one

Find a dead octal tube, break off the glass, and use the base.

Hi Skip, First thanks Bill for allowing Skip to list tubes, I’m sure there are several of us that can benefit from it. ?I’m restoring my Collin’s 32V-1 and could use a 4B32 for the final.

?Absolutely yes. I added to a friend’s SX-100 (and SX-111) a three wire cord, panel mount bayonet fuse holder, and X1/Y2 safety caps on the incoming line and neutral. Dan WB4GRA

Also forgot to ask this as well.... Since these radios were never designed to use a 3 wire AC cord, is it wise to add one? I have read conflicting information on going this route. 2 of my SX radios

If a DC power plug is not available for the back of one of the SX series radios, is it safe to bridge across the terminals inside the radio? Think its pin 6 & 7 but dont remember for sure. Or a

I believe it was the norm for 1960s transceivers. The Collins KWM-2/A and Drake TR3/4 series transceivers were designed primarily for mobile SSB operation and have similar CW limitations. I recently

For sentimental reasons, I've been on the lookout for an S20 R model, and decided to take a chance on an Ebay sale of an "as is" unit.? The cosmetic appearance didn't look too bad, and the fact that

Wondering if any of you can give me some insight as to rigs production date. Radio 1. No serial tag on back 199724B inside chassis Has copper strap Has production 3 updates Radio 2. 452002. 825001 in

A lot of people complained about the sidetone issue, that is why the 400 and 2000 have sidetone. Walt Cates, WD0GOF https://wd0gof.com/Hallicrafters A majority of acceptance is not proof of

Hope I have success with the two rescues I picked up last summer also. Now that the wife is well on her way to recovery from the knee replacement I should be able to spend some time at the work bench

Here is a different Sprague ad See the rest 0n pdf 22 https://www.worldradiohistory.com/Archive-Service-Magazine/50s/Service-1953-03.pdf

Beautiful job Don! I have a LOT of Hallicrafters gear but I have never had an SR-150.?? I have little to no room for any more gear but if I found a nice SR-150, I would make an exception!! --

A beautiful restoration job, Don. 73 – Mike Mike B. Feher, N4FS 89 Arnold Blvd. Howell NJ 07731 Sent: Friday, March 29, 2024 7:02 PM To: [email protected] Subject: [HallicraftersRadios]

I always wondered why there was no built-in side tone for CW in this rig. Possible reasons:Primarily intended for SSB use?Primarily intended as a mobile rig?Expected CW ops to be using the Halli

There are those who say the SR-150 was Hallicrafters best ever transceiver. Thanks for the kind words on the repair document. They are all living documents, ever few months I take one and update it.

Last summer I picked up a SR 150 and matching power supply/speaker. It was in the typical dirty scratched condition and didn't work. I wanted to say that Walt's repair manual was invaluable. I did the

After the first of spring’s yard work today, took the SX100 case into my bead blast area. Hit it really good with 80 grit bead blast then ?good wet sand with 180 and 320 grit paper. Looks so much

Sure, someone may need what you got. *K2WH Bill's QRZ Biography ( https://www.qrz.com/db/k2wh ) * ---------------------------------------------------

Did that early in the restoration process, but maybe didn't do a good enough job.? Will revisit it - thanks. 73, Floyd - K8AC