开云体育

Wondering if any of you can give me some insight as to rigs production date. Radio 1. No serial tag on back 199724B inside chassis Has copper strap Has production 3 updates Radio 2. 452002. 825001 in

A lot of people complained about the sidetone issue, that is why the 400 and 2000 have sidetone. Walt Cates, WD0GOF https://wd0gof.com/Hallicrafters A majority of acceptance is not proof of

Hope I have success with the two rescues I picked up last summer also. Now that the wife is well on her way to recovery from the knee replacement I should be able to spend some time at the work bench

Here is a different Sprague ad See the rest 0n pdf 22 https://www.worldradiohistory.com/Archive-Service-Magazine/50s/Service-1953-03.pdf

Beautiful job Don! I have a LOT of Hallicrafters gear but I have never had an SR-150.?? I have little to no room for any more gear but if I found a nice SR-150, I would make an exception!! --

A beautiful restoration job, Don. 73 – Mike Mike B. Feher, N4FS 89 Arnold Blvd. Howell NJ 07731 Sent: Friday, March 29, 2024 7:02 PM To: [email protected] Subject: [HallicraftersRadios]

I always wondered why there was no built-in side tone for CW in this rig. Possible reasons:Primarily intended for SSB use?Primarily intended as a mobile rig?Expected CW ops to be using the Halli

There are those who say the SR-150 was Hallicrafters best ever transceiver. Thanks for the kind words on the repair document. They are all living documents, ever few months I take one and update it.

Last summer I picked up a SR 150 and matching power supply/speaker. It was in the typical dirty scratched condition and didn't work. I wanted to say that Walt's repair manual was invaluable. I did the

After the first of spring’s yard work today, took the SX100 case into my bead blast area. Hit it really good with 80 grit bead blast then ?good wet sand with 180 and 320 grit paper. Looks so much

Sure, someone may need what you got. *K2WH Bill's QRZ Biography ( https://www.qrz.com/db/k2wh ) * ---------------------------------------------------

Did that early in the restoration process, but maybe didn't do a good enough job.? Will revisit it - thanks. 73, Floyd - K8AC

Try cleaning the Band Selector switch. Every One of my Halli’s has had the same problem with dirty Band Selector switches. One the contacts are cleaned, the radio comes back to life. Good Luck.

I was listening on my recently restored SX-117 the other day and discovered that the sensitivity is way down on 10 and 15 meters compared to 20M and below.? While the preselector peaks on 10 and 15,

MAX-GAIN SYSTEMS | Home | Fiberglass, RF Connectors & Adapters (mgs4u.com)<https://mgs4u.com/#Bristol> [cid:4bb3f152-b3ef-4caa-9a9f-39e37f5f1df5] Walt Cates, WD0GOF https://wd0gof.com/Hallicrafters A

I have and use the Xcelite Bristol/spline wrench set with torque amplifier handle. Best for the long reach so often required. I also have a bunch of the L wrenches gleaned over a long time from

Jacques , I have been trying to find out about the Sprague product line from the 1948, 1949 telecaps ..black beauty and onto the hcx and difilm but it is not so simple. Anyhow I ran into that ad, and

FWIW, in my mispent youth I worked for Hewlett-Packard, mostly on RF gear. We washed equipment, simple washing but followed by a long baking out process. Typically a minimum of 48 hours at about 130F.

The 45 below is some sort of typo. Should read Set of L wrenches without number. There are 9 keys in a blue plastic bag. -- Richard Knoppow Los Angeles WB6KBL SKCC 19998

Thank you for having find this, Don. I have many Sprague 160P in my capacitors bins and they all survived, 60 + years after they were made. My actual limit of leakage detection is 10nA at the WVDC of