CHECK OUT THE WIKI The purpose of the wiki is mainly to allow you to find information on instruments, either from either
- The model number
- The function(s) listed below. Some instruments have multiple functions - for example, the 4195A is a VNA, spectrum analyzer and an impedance analyzer. Therefore the 4195A is listed in multiple categories
Please also check out HPWiki available here:
- Accessory kits - various types
- AC power analyzers - PA2201A and PA2203A
- AC power supplies 6811C, 6812C, 6813C
- Airlines
- Arbitrary waveform generators M8194A
- Amplifiers?493A, 495A?
- Attenuators (optical) 8156A, 8157A, 8158B, 81566A, 81576A,?
- Attenuators (RF) 8494A
- Attenuator set (500 ¦¸) 350C
- Attenuator set (600 ¦¸) 350D
- Attenuator switch driver
- Audio analyzers? 8903A, 8903B, 8903E,? ?
- Base station test sets
- Bit error rate testers (BERTs)
- Cables
- Capacitance meters U1701A, U1701B, 4272A, 4278A, 4279A
- Capacitor Bridge 4270A,
- Capacitor standards 16380A, 16380C,?
- Carrier noise test setsi
- Cesium frequency standards
- Clamp ammeters
- Close field probes
- Crystal Impedance E4915A, E4916A
- Data Acquisition Systems (DAQs)
- DC power analyzers
- DC power supplies 6030A , 6031A , 6032A, 6033A, 6035A, 6131C, 6621A, 6622A, 6623A, 6624A, 6627A, 6255A, 6645A, 6671A, 6672A, 6673A, 6674A, 6675A, 62003A, 62003C, 62003E, 62004A, 62004B, 62004E, 62005A, 62005B, 62005E, 62006A, 62006B, 62006E, 62010A, 62010C, 62010E, 62012A, 62012C, 62012E, 62015A, 62015C, 62015E, 62018A, 62018C, 62018E, 62024A, 62024C, 62024E, 62028A, 62028C, 62028E, 62048A, 62048C, 62048E
- Delay lines
- Detectors
- Device current waveform analyzers
- Digital communications analyzers
- Directional couplers
- Distortion analyzers 330B, 330C, 330D, 331A, 332A, 333A, 334A, 339A, 8903A, 8903B, 8903E,???
- Dynamic measurement DC source
- Electrometers
- Fading simulators
- Femto ammeters
- Filters
- Frequency counters 522B, 5342A 5343A 5352B
- Frequency standards?
- Function Generators ? 3310A,? 8165A,
- GPIB controllers, extenders, cables etc.
- GPS frequency standards
- Harmonic mixers
- High resistance meters 4339B
- High resistance meter fixtures 16008B
- HEV EV Grid Emulators and Test Systems
- In-circuit test systems
- Impedance analyzers 4195A, 4291A, 4291B, 4395A, 4396A, 4396B, 4294A, E4990A, E4991A
- Impedance Analyzer Accessories
- Impedance / Gain Phase analyzer 4194A
- Impedance Meter 4193A,
- Isolators
- LCR meters? U1701A, U1701B, U1731A,? U1731B, U1731C, U1732A, U1732B, U1732C, U1733C, 4191A , 4192A, 4194A, 4195A, E4196A,? 4216A, 4260A, 4261A, 4262A? 4263A, 4263B, 4271B, 4274A, 4275A, 4276A , 4277A, 4284A, 4285A, 4286A, 4287A, 4291A, 4291B, 4294A, 4332A, 4342A, 4395A, 4396A, 4396B, E4980A and E4980AL
- LCR meter calibration devices? 16380A 42030A? 42090A, 42091A and 42100A
- LCR meter accessories
- 2-Terminal BNCs.
- 4-Terminal Pair (BNC connectors)
- Cable extension 16048A, 16048D, 16048E, 16048G, 16048H
- DC current bias accessories 42841A, 42842A, 42842B, 42842C, 42843A
- DC voltage bias accessories 16065A, 16065C,
- Kelvin clips 16089A, 16089B, 16089C,16089E
- Lead Components 16047A,16047B, 16047D, 16047E
- Material 16451B, 16452A
- Probes 42941A
- SMD 16034E, 16034G, 16034H
- 2-port 16096A
- 7 mm (APC7)
- 2-Terminal BNCs.
- LCZ meters? 4276A, 4277A,
- Lightwave clock / data receivers
- Lightwave converter
- Lightwave component analyzer
- Lightwave measurement system mainframes
- Lightwave polarization analyzers 8509B
- Logic analyzers
- Nemo wireless network solutions.
- Noise and interference test set
- Noise figure analyzers
- Noise sources 346A, 346B. 346C ,
- Matching pads (50 ohm to 75 ohm or similar)
- Materials test equipment
- Microwave repeaters
- Microwave downconverters 70427A
- Microwave / THz sources
- Milliammeter 428B
- Milliohm meter
- Mobile communications DC source
- Modular instruments
- AXIe
- Data acquisition (DAQ)
- USB
- PXIe
- Modulation analyzers
- Multimeters 427A, 970A
- Optical attenuators
- Optical heads
- Optical sources
- Optical spectrum analyzers
- Oscilloscopes 120A, 120AR, 120B, 122A, 130A, 130B, 130BR, 130C, 140A, 140B, 141A, 150A, 150AR, 160B, 180A, 180AR, 180CD, 181A, 181AR, 181T, 181TR, 182C, 182T, 183A, 183B, 184A, 184B, 185A, 185B, 1200A, 1200B, 1220A, 1221A, 1703A, 1707A, 1707B, 1710A, 1710B, 1715A, 1722A, 1725A, 1726A, 1740A, 1741A, 1742A, 1743A, 1744A, 1746A, 1980A, 1980B, 5403A, 6000A, 6000L, 16533A, 16534A, 54100A, 5410B, 54100C, 5100D, 54111D, 54120A, 54120B, 54200A, 54501A, 54502A, 54503A, 54504A, 54520A, 54520C, 54540A, 54540C, 54542A, 54542C, 54600B, 54601A, 54601B, 54602B, 54603B,? 54645A, 54654N, 54710A, 54720A, 54750A, 54825N, E1428,?
- Oven controlled crystal oscillators (OCXOs)
- Pattern generators
- PCM terminal test set
- Phase noise measurement
- Pico ammeters
- Printers 2225
- Plotters 7470A, 7475A?
- Probes
- Protocol analyzers and exercisers.
- Power booster test sets
- Power meters 431A, 431B, 431C, 432A, 435A, 435B, 437B, 438A
- Power splitters
- Power supplies
- Pulse generators
- Q-meters 4342A?
- Q-meter calibration inductors 16470A
- Reflection transmission test set
- Return loss module (optical)
- Relays / switches / switch matrices (optical)
- Relays / switches / switch matrices (RF)
- Resistor standards 42030A?and 42100A
- S-parameter test sets
- Scalar network analyzers
- SCSI bus preprocessor interface E2324A
- Selective level meters 3746A
- Semiconductors
- Semiconductor parameter analyzers 4145A, 4155B, 4156B,
- Signal analyzers
- Signal generators / sweep generators / signal sources / oscillators 200CD, 201B, 209A, 204D,? 608A,? 8165A
- Software
- Source measure units
- Spectrum analyzers 4195A,???
- Switch control units
- SWR meter 415E?
- Time interval? counters
- Time mark generator 226A
- Timing and data state modules
- Torque wrenches
- Transmitter testers
- Trigger modules
- Ultrasound transducers
- Universal bridge? 4260A, 4265A, 4265B?
- Vacuum tube voltmeter 410C
- Vector Impedance Meter 4193A, 4800A, 4815A
- Vector Network Analyzers (VNAs) 4195A,? 8510A, 8510B, 8510C, 8753A, 8753B, 8753C, 8753D, 8753E, 8753ES, 8752ET, 8719A, 8719B, 8719C, 8719D, 8720A, 8720B, 8720C, 8720D, 8720ES, 8722A, 8722B, 8722C, 8722D, 8722ES,
- Vector Network Analyzers (VNA) calibration kits 85032B, 85032E, 85033C, 85033D, 85033E, 85050B, 85050C, 85050D, 85052B, 85052C, 85052D, 85054A, 85054B, 85054D, 85056A
- Vector Network Analyzer (VNA) verification kits
- Vector Signal Analyzer 89650S, 89600S
- Vector voltmeters 8405A, 8508A,
- VXI mainframes 70000B, 70000C
- Waveform and function generators
- Waveguide to waveguide and waveguide to coaxial transitions.
- Wireless 58 OTA chambers
- Wireless channel emulators
- Wireless network emulators
- Wireless communication test sets
?
|
Re: HP8592L level issue
After some investigation ... and with the levels from the manual, it would
appear it is the YTF that is faulty ... the attenuator is fine, levels
check perfectly ... I cannot imagine it is the relay,
By
Robin Szemeti
·
#119886
·
|
|
Re: HP Product Note 8756-3
Ken- You look to be replying to Guy but as the instigator of this thread I should advise that I had a couple of off-list replies with offers of a pdf of the 8756-3 Product Note so I¡¯m all OK.
By
Dave Brown
·
#119885
·
|
|
Re: HP200CD oscillator
Typo Alert!
Should have read: If V1 & V3 are out of balance, V2 & V4 will be also.
By
Jim Adney
·
#119884
·
|
|
Re: HP200CD oscillator
One thing to note is the symmetry of the circuit. If R30 is getting hot but R31 isn't, then that symmetry has been broken somewhere. I'd start by comparing tube socket voltages between V1 & V3 and V2
By
Jim Adney
·
#119883
·
|
|
Re: Fibber optic connectors
I have a good collection of fiber and fiber accessories that I would be willing to trade or volunteer to a good cause.
Show me a picture of the connector or let me know what the manual says and I
By
Bruce
·
#119882
·
|
|
Re: HP200CD oscillator
Sprague "Bumble Bee" and "Black Beauty" condensers were molded improperly, and they will crack, especially the oil filled ones, and let in moisture. That seems to react with the oil and make it
By
greenboxmaven
·
#119881
·
|
|
Re: Fibber optic connectors
Well, it's been a while since I've done anything with fiber, but I used to subscribe to Laser Focus World, Photonics Spectra, and Fiber Optic Products Digest magazines.? I think there was also a
By
Jim Ford
·
#119880
·
|
|
Fibber optic connectors
Dear all can someone please guide me to illustration of the different Fibber optic connectors
also the cheapest way to get an optical source as i want to test out an optical analyser I was
By
Paul Bicknell
·
#119879
·
|
|
Re: HP200CD oscillator
?? Who made those? Some early advertising for Sprague Black Beauty caps said they were plasticized paper. The main problem with these is some sort of production problem they had. I have dissected a
By
Richard Knoppow
·
#119878
·
|
|
Re: HP200CD oscillator
??? Black Cat or Black Beauty, never heard of Black Cat. Black Beauty was a trade name of Sprague, they are notorious. Modern polypropylene caps are about the best performing of the plastic caps,
By
Richard Knoppow
·
#119877
·
|
|
Re: HP200CD oscillator
Even the later plasticized-paper ¡°Prokar¡± and ¡°DiFilm¡± versions can cause trouble in some applications ¨C they may not be leaky, but their Dielectric Absorption and Dissipation Factor are
By
Dave Wise
·
#119876
·
|
|
Re: WTB: PIC17C42A-33I/L or PIC17C42A-33E/L
The hex file created for PIC17C44 is identical to that for PIC17C42A ¨C so can use them without even needing to change the code.
Sent: 04 November 2021 13:40
To:
By
David C. Partridge
·
#119875
·
|
|
Re: HP Product Note 8756-3
Hi;
I sent an email to the vendor asking for photos of the product note which he has supplied and I have attached the photos.
I don't know what has gone south but since he has responded to me I
By
Ken Eckert
·
#119874
·
|
|
Re: HP ET8866 True RMS meter - any info on this?
ETs are Engineering Tools, that were specially built or modified for
internal use like production testing, adjustment purposes or similar.
Therefore, usually there is no official, public information
By
Thomas Butterstein
·
#119873
·
|
|
Re: WTB: PIC17C42A-33I/L or PIC17C42A-33E/L
Thanks ¨C yes a PIC17C44 should work OK if I re-assemble the code using pic17c44a.inc - may even work w/o reassembly
David
Sent: 04 November 2021 08:58
To:
By
David C. Partridge
·
#119872
·
|
|
Re: HP200CD oscillator
ALL Sprague "Black Cat", "Black Beauty" and? color striped "Bumble Bee" condensers should be considered bad on sight. Unfortunately, they are common in older equipment of all makes and models. The
By
greenboxmaven
·
#119871
·
|
|
Re: HP200CD oscillator
My unit has Black Cat 0.5MFD 400v axial capacitors for C8 and C9. Would 630v polyester unpolarised caps be ok replacements?
By
Richard Merifield
·
#119870
·
|
|
Re: WTB: PIC17C42A-33I/L or PIC17C42A-33E/L
Hi David,
Nexxon shows stock, you'll have to get a quote to see if its real & affordable.
https://www.nexxoninc.com/part/PIC17C42A-33I-JW/
Microchip keeps switching to the PIC17C44 rather than
By
GT
·
#119869
·
|
|
Re: HP ET8866 True RMS meter - any info on this?
Thanks to all who replied!
By
Jim Allyn - N7JA
·
#119868
·
|
|
Re: HP ET8866 True RMS meter - any info on this?
That is not quite the way it was done at Loveland HP, I'm sure it depended on the division and when in HP history it was designed.? Most instrument division ETs from the 70s and early 80's at least
By
freshndaire
·
#119867
·
|