开云体育

hi guys i am trying to locate a hp part or compatable part out of a hp8558b it is a hp part number 5062-2805 or sugest a online cross reference guide i can check out Thank you , Ian Wells, Kerinvale

Well, looking at this here manual, there is a RUN/TEST switch (A1S1). The test switch is A1S2 ( 6 pin DIP sw) . You need to set the COAX/OPT switch (A1s5) TO coax... finally, you have to set the

If I Recall, The Maximum Cable Length For HP-1B Was 20 Meters. Perhaps Someone Else Knows For Sure. Greyhawk

I've recently tried to use a pair of old 37203A HP-IB Extenders to extend the distance of several IEEE-488 instruments from the controller. I don't have a manual on hand, but I thought the units

I'm looking for service & cal info or manuals for the following. HP 8640B Opt.323 (not commercial 8640B) AN/USM-323. AN/USM-338 oscilloscope. Any leads would be much apprieciated. Roger

Ian, In the HP 8558B service manual, it looks like those switches are just assemblies of many different HP part numbers. I could be wrong. I've never looked at an 8558B. But I didn't notice a part

Would anyone know where I can obtain the rotary switches on the front panel of a HP8558B plugin? thanks ian

Does anyone have any CPU Board data. I have the service manual such as it is. I'm having a problem with the analog bus voltages coming up as out of range when I measure them within

HI guys I have a HP 8558b with a hp182t m/f I have two problems one is the display on the 182t shows a sharp dip in the middle of the screen wether the 8558b is plugin or not . the second is the 8558b

From what I have heard (so cant confirm) is that when the progs are copied from the orig disks there is a bit set on the orig and the copy of the program that allows only one copy. If the orig

Lloyd I'll gladly contribute some dead A/D boards to the reverse engineering cause. This board is probably the single largest failure card in the 54111D family. People will buy up 54111D carcasses

I am interested in manufacturing replacement A/D boards for the HP 54111D. I saw comments on the unavailability of schematics. Does anyone have further info on contacting Agilent or reverse

<mike@a...> wrote: my They Probes leads are passive. You just need suitable 0.154" conector blo

hp_agilent_equipment@... writes: Gentlemen: You might try an MTA-156 IDC receptacle used for wire-to-board interconnection. They are available for about $1.00 each. The 12 position

Yes. That's it. But... The HP1631D is a different (older) unit than I thought. So, my advice isn't as applicable. Looking at the pictures in the two auctions below, the probe tips

Hello Mike, you sells. most the you Do you mean this pdf? http://cp.literature.agilent.com/litweb/pdf/5968-4632E.pdf The logic analyzer has the PODs. and they contain - as far as I can see -

Keep an eye out on ebay. Every now and then, someone puts up a set of grabbers (just grabbers without the pods) and they tend to go for about $20 per set of 20 grabbers. Of (just in case I

My usual plea.......anybody have a list of 3586c commands? (I never get manuals with my stuff)... Thanks to all who replied regarding the peeling meters and all.. 73 Tom

I have a 1631D with all the Pods, but missing grabbers... And finding affordable kits has been impossible... Is it possible to make grabbers myself? I thought the Pods have MTA 156 connectors.. And

Hi All I have obtained some software for the 4952A protocol Analyser. These have been copied using the LIFUTIL utility. However wheras the data files work fine the applications (things like a VT100