开云体育

Good info that pointed me in a direction I was wanting to go with the 16601A.? I was thinking about using the Noctua fan on my TDS-520 mod test bed. Specs don't match however. Are there any other

I had trouble with the SCSI2SD v6 in both a 16702A and a 16702B.? Inertial Computing couldn't really figure it out either.? I finally tracked it down to the SCSI2SD couldn't be on the same SCSI

I have a 16702B logic analyzer, and I was unable to get the SCSI2SD v6 to work on it after over a month of back and forth with Inertial Computing.? They thought it was a signaling level problem and

Those plug-in fuses are convenient but expensive. Just replacing missing ones can take a lot of money at over $5 a pop, and if they start blowing and you have to troubleshoot, it can get quite

The 4145A/B uses the well known 1345A display module. You can find this in innumerable other instruments. [email protected]> wrote:

Hi, I have a problem with this instrument. In analyser mode, when I will activate Zoom function, it freeze during two long minutes and then it works. When I push Next Window, again 2 long minutes

Neil, probably the “ancient” XP virtual machine would be ideal. If you could also do a full Wireshark capture while doing the update, it might be possible to reverse-engineer the protocol and

When I try to use the Agilent firmware updater (from the website) for my E4406A, I get warnings about the ancient MS JVM it tries to run.? If I mess with the path, I can get it to run, but although

Thanks Dick, I think I do some cherry picking on your matlab effort. Actually did a lot matlab work during the last two decades of my working life. Saw some interesting instruments among them and use

Hi all, My trusty E6380A failed to proceed this morning and preliminary investigations as to the cause prove zip. Do these things have a common fault I could go look for ? Any pointers to what might

If you send me an off list email, I can look for some old code re that. I used a HP 6624A and a Solartron 7150. Tam --- With best regards Tam HANNA (emailing on a BlackBerry PRIV) Enjoy electronics?

Wow, excellent contributions. I have been wondering if I could get my power supply to act as a rudimentary curve tracer over GPIB and it looks like you've already done it. I only have a self-built

Hi Don -? I gather from your call sign that you're in New Zealand.? I'm not sure if Digi Key will be much use (seems to me guys on the eevblog from Aus and NZ mention using them, so maybe...), but

I`ve had a look for these [Littelfuse 027001.H , 027004.H , 027004.H.....1A, 4A, and 5A respectively] on the internet, including the manufacturer, and their local agent, here, and others. I`m looking

I didn't notice those, thanks.? Downloaded. I'll contact Keysight and see if they have a copy somewhere else since nothing is referenced online regarding the 16601A when I checked.

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the [email protected] group. *File:* 16600-97010.PDF *Uploaded By:*

A 16600 series should be easy to open. Two T-10 screws on the top edge of the case on the back, plus two T-15 screws holding the carry handle on the side. Then the case should just slide off

I can use a copy since I don't have the vers 1.51 re-ignite or any documentation or software. I've only powered on and looks like no errors and my IBM PS/2 Keyboard and Mouse are working along with

HP / Agilent 40-pin to 17-channel flying lead (16 data + 1 clock lead) PODs are all the same from the 1650, 1660, 1670, 1680, 1690, and 16600 series analyzers, and the 16510A modules all the way up

Thanks for the suggestions. It ends up the 74160 is pin compatible with the 86L75, and I found a 74LS160 in the lab. The counter is back up and running. Gary Appel Sent: Monday, October 01, 2018 12:33