开云体育

Hi , I tried so many objects M27 South and North M52 , NGC281 , NGC146 all in Cassiopeia and always did Meridian Flip. One only thing I am worry about short message from Gemini.net? "Serial Port

Hi Robert , Thanks for response . I am just confuse because you talking about Max/min two settings but I see only one Minutes after Meridian or you using different version of NINA . I am using 1.10

Hi Roman, I too have the Genimi 1 and use NINA.? It would not flip at first and I found that it is all to do with the Max/min Minutes after meridian (two settings) and the east and west safety

Hi all , I can sleep now LOL Three weeks ago accidently? damage my Gemini1 controller and motors just fall? asleep . I tried flip twice yesterday w/o success and today I just connect my QHY268M

Folks, for those reading Groups.io?messages on your mobile devices, there is now a mobile app that you can use to do so: * iOS: https://apps.apple.com/us/app/groups-io-app/id1553820507 * Android:

As David said, use a volt meter to measure your "3V" battery while it is still in the Gemini. Easiest way to do that is use a ground point on the G-1 board for the - probe of the voltmeter. I find the

Forgot to say..."CMOS reset" means the contents of the SRAM was lost on power down and reset.?? This data is lat/long time zone DTG etc etc etc So find why it lost the data...usually bad

After you change the battery and enter location lat/long time zone offset etc, and remember Gemini 1 DTG time is in a peculiar format...see here ( http://www.docgoerlich.de/utcdate.php ). ie: UTC

Change the battery. If you keep getting the message after doing that, then there’s a problem with the hardware. David Sent: 07 November 2021 01:48 To: [email protected] Subject:

UTC is -0.. LOCAL is -7.. They don't mix! Either enter UT and an offset of 0, or Local and an offset that's appropriate.. This is a better question for the LOsmandy group.. I would ask there.. Things

I've been trying to figure out what I am doing wrong when I try to align my G-11 with Gemini 1.? When it starts up gives me a CMOS reset warning. I then enter location and time zone and UTC (-7 here

Hey Leo.. The Phone is unreliable here for the past 6 months.. I think we lost a cell tower during a heatwave.. Anywho, I will be going to Kaiser SJ later (3 or 4) or you can reach me at breit

Hi Everyone, Heads up for those observing Daylight savings time, primarily in north america Daylight savings is changing on November 7th. For those of you affected, your timezone will fall back one

Philippe, Whenever I put a new telescope on my G11, I use the MI-250 limits, which are the most conservative at 95 and 92 degrees. If I see there is more room for the camera end to go, I will increase

Hello all, I use my G11 with current slewing from CWD park to Az 130 deg/280 deg. and scope TMB130 on left side. Depending of the target altitude and the risk to hit the tripod I may like to start

Hi Ron, Basically giving you a different perspective, and a method I have found works with different mounts. Brian and I are friends beyond our preferred mounts. (Which my 811 was bought against his

Hi Sonny Thanks for your feedback of this concept Brian is our guru and points the way - modeling is just to " get to the object ". So because platesolving defines where everything is, the idea of?

Hi Nikul! I often think the best problem is one that goes away by itself. But then later it comes back... So now you know what to look for if it happens to you again. Have fun! It is finally raining

Thank you very much to Michael, Paul, Brian and Chuck... To my surprise I was not able to reproduce the issue last night... I don't know why the issue did no surface last night... I was not able to

sells. I use it all the time (pun intended!) and have never had a problem with geographic location and time. Well worth the cost, in my opinion yes, definitely the Losmandy GPS is a great tool for