开云体育

Are you setting menu 59 while the MH-36 is connected? According to the manual Before connecting the MH-59 A8J , you must instruct the FT-857’s microprocessor that the MH-59 A8J is being used.

Hi, The older FT-857 supports the MH-59a8j microphone.? FYI:? The remote microphone was released at the same time as the original FT-857. If the FT-857 doesn't show the RMT option under Menu 59 it

If RMT does not appear in menu 59 between NOR and CAT, I suspect it means you have an early FT-857 and not the later FT-857D. 73, Kent K9ZTV

I am trying to add the mh 59 mic. Selecting menu 59 I see only NOR and CAT? ? RMT is not an option this is second attempt to post sorry for the dup if first posted

I have a MH 59 a8j? Mic.? ? When I select menu 59? I am presented with only NOR or? CAT as I rotate the knob.? ?RMT is not an option.? ?The mic is plugged in.? ?Any ideas what I've done

Thanks for the quick reply, everyone. This very helpful. I will follow up with suggestions. - George

I sent mine to Yaesu in California recently. I received an e-mail that it is in the queue for repair. How long they will take, I don't know. 73, Zack W9SZ [email protected]> wrote: [image: width=]

I have had a couple of 857’s worked on by this guy. Send him an email and see what he can do. Andy Ruggiero WD8BWW andyit28@... 73, George W8CFI

I've had good service from HamradioRepair.com. Ronald Jakubowski K2RJ

I had a guy Byron Campbell WA4GEG repair a Yaesu for me some years ago. He says he does not do the 857. He did list others on his page who work on different model Yaesu's.? He gave the name Andy

A few years ago I tried to add a module to the receive section of the FT-857 in order to connect to a computer for a waterfall/panadpter, but I damaged a couple of the SMT resistors. The radio

OK.. Update... After conferencing with a friend I figured out that the CAT connection that the YT-100 tuner uses is different than the 6 pin connector the SignaLink uses.? Got it all connected last

I have a FT-857D in my go kit, have the YT-100 auto tuner and have been using this with HRD on a laptop.? I want to run digital FT-8 with this setup but don't see how to have both the YT-100 and

ALWAYS, call Yaesu Tech Support before doing any resets. It may be a simple problem that can be corrected without loosing all your data you have storied in the radio. Its a free service. K3CLT Chuck

Hi Alex, Thanks for the tips. as I use the speration kit YSK-857 in my shack, the idea was to connect back the little RJ-45 cable to the radio instead of the long one. After reading your message, I

Time for some housekeeping. I have a very lightly used Yaesu 857 system for sale. Purchased (2nd owner) in Palm Springs CA in 2017 (as a snowbird) when I obtained my Tech certification. Not energized

What happens if you do a master reset?

The same issue i have many years ago. After few days off and power supply not connected all was ok. Why i dont know. 73 Alex OK4AS PS: Sri for my english hi... Dne st 27. 7. 2022 18:11 u?ivatel

Have you tried exercising the control head to body cable? Bothe ends? Regards, Tony F. VA7TF VE7ACF Sent: July 27, 2022 10:20 AM To: [email protected] Subject: Re: [FT-857] Switching on/off my FT-857D

Thanks Tony, Power supply is around 13.97 V and when 857 is powered ON, there is no difference (14.01 V). Thierry