开云体育

Thank you Barron But I am using it. Almost all the cable (Data and Power) is using looped beads or single beads. Still it is troubling. Any will carry on investigating. Hope can be done with it. 73s

It has little to do with the SWR seen by the transceiver, but rather the RF in the shack. A few ferrites on the USB cable(s) and the CAT may help. If you have one that you can make several loops

Ron, You were spot on!? It was the chip fuse.? ?I had terrific service from Yaesu in Los Angeles. Sent it in on July 19 and got it back fixed on August 16th.? ?VERY reasonably priced as well.

Hai all When I tune my 857 and with my LDG 1000 pro-II, ant. tuner on 40 mts (Only 40 mts) *the software gets disconnected*. The dig. interface used is Link-5 (BY make) with CH340 driver. I feel may

You can use my yc1-bt to do? a Bluetooth link from your radio... Take a look at www.ve2dx.com -- 73 Richard VE2DX Lead Designer and President WWW.VE2DX.COM ( /g/ft817/WWW.VE2DX.COM )

I use the DigiRig, works great! KB8VUC

Greetings, You may look into the Yaesu SCU-17.? It is compatible with the FT-8x7 series radios and provides both CAT control and sound card interface for FT8 and other data modes. I've been using it

Thanks Troy, Haven’t had that problem (yet) but appreciate the info. Regards Albert VK3BQO Sent: Tuesday, 16 August 2022 6:40 AM To: [email protected] Subject: Resolution: Re: [FT-857] menu 59

I used: Mark V. Dunkle, KJ6ZWL BlueMax49ers eBay & Amazon Seller DunkleM@... Cell (408) 832-2954 1385 McBain Ave. Campbell, CA 95008-0725 USA Top Rated Plus FTDI Chip ? USB Programming Cables

Thanks Troy for the feedback. 73 de Thierry, F4GVO

To any still interested. The resolution to the missing RMT menu item in menu 59 was to do yet another total reset. 73 NW1B Troy Dennen Sent: Tuesday, August 9, 2022, 10:31 To: [email protected]

Thanks. I was considering the RT software (I have it for various other radios) so that seems to be the answer. Paul Braun WD9GCO Anchor, Amateur Radio Newsline Certified Music Junkie

I can confirm that the RT systems Yaesu-specific cable will work, and is likely the best option. A warning: generic cables, and cables for other radios, such as Kenwoods, with the mini-DIN connector

I’d like to use my non-D 857 with HRD in the field. I’ve found several cables online, but it’s hard to judge actual quality from a web listing. I turn to the hive mind here — what’s the most

Not to belabor the subject, but mine is mounted on an air-conditioner louver via a ProClip. It stays as cool as I do. Whether this has prevented display issues, I don't know. 73, Kent K9ZTV

I live in Central Florida. I had my head unit mounted low on the front console on my Honda Element. It was always out of direct sunlight. I even had a soft cloth covering it when I wasn’t using it.

You can try putting you AC as cold as it will go and see if the screen gets better. Or put it in the fridge and see what happens. I had mine fixed a few years ago and have had in a backpack since to

From the sound of things, that could be as simple as a solder joint refusing to pass electrons until heat expands it. I've brought radios back to life, cured hums, and surprised myself on several

Interesting problem that is not limited to 857D. My 857D was purchased new in about 2005 and kept in my truck in South Florida. The zebra phenomena did occur the first time a couple of years later and

I just powered mine up to do an informal test.On first power, 17 of the pixel columns were blanked out. Over a period of about two hours, ten of them self "repaired" or "healed".This was with rig