开云体育

From: dxlab@... [mailto:dxlab@...] Sent: Saturday, February 27, 2016 9:23 AM To: dxlab@... Subject: [dxlab] /P /QRP setup and other Question 1. Where does one

OK, I can't explain it then. I just checked to be sure there wasn't some malfunction in DXView since I always have that and its built in world map open but there wasn't. If it's minimized when

From: dxlab@... [mailto:dxlab@...] Sent: Saturday, February 27, 2016 9:19 AM To: dxlab@... Subject: RE: [dxlab] DXView Starts Maximized I made sure to save the

I assumed that to be the case with eQSL. So I attached the /QRP account to my other “primary” account nicknaming it “/QRP.” But now I cannot log into the QRP acct to pull images (if any) from

Not sure about LoTW but for eQSL you need separate accounts for each modified call. Otherwise users will send eQSL's to the call you signed on the air I.E.: K3JAE/QRP and if no such account

Couple of questions: 1. Where does one set up the default HomeQTH at in DXLabs? Setting up a laptop for /P and or /QRP operation and I cannot find where it is set up. 2. I am setting up for /P

I made sure to save the settings with it minimized. Pete, W1RM Sent: Saturday, February 27, 2016 8:29 AM To: dxlab@... Subject: Re: [dxlab] DXView Starts Maximized Are you

Commander directly controls your 6700 via the network; neither SmartCAT nor a serial port is used. Step-by-step instructions are here: <http://www.dxlabsuite.com/dxlabwiki/FlexSignature>

I previously owned a Flexradio 6300. I also have a Yaeus DX-5000. I was able to get both of them to work with DX Lab commander---reading frequencies. I just upgraded to a Flex 6700 and I have

Are you possibly executing a "Load settings from Workspace" at start up and was DXView maximized at the time you ran "Save settings to Workspace" ? 73, Rich - W3ZJ

The good news is DXView started minimized dong this. The bad news is DXView came up full view when I started it via Launcher. Pete, W1RM Sent: Friday, February 26, 2016 8:45 PM To:

Ah, but it is! As long as you take the time to *understand* the manuals and do the job the way the software/hardware developers intended of taking a "my way or the highway" attitude. I have done

From: dxlab@... [mailto:dxlab@...] Sent: Friday, February 26, 2016 10:00 PM To: dxlab@... Subject: [dxlab] Tracking most recent eQSL dates in DXK with

It's not as simple as reading manuals. There are problems galore that no manuals address because they're very specific to one and only configuration on a custom-built PC; I've run into about 5 or 6

Dave - Currently DXKeeper appears to track, as a database field, the date of the most recent EQSL and LOTW download, so that requests for new QSL downloads only need to go back to the most recently

---In dxlab@..., <aa6yq@...> wrote : *** Oh, trust me, I did! I didn't notice this decode thing until today and it's nothing that I would have ever considered rolling back as a result of.

I like cards so, at 13 cents and no hassles, I QSL everybody Buck k4ia K3 #101 Honor Roll 333 8B DXCC

+++ I do not plan to run NaP3 with N1MM. For contests, my plan is N1MM+ +++ and Skimmer only with Bridge and the LP-PAN running. If you do not plan to run NaP3 with N1MM, configure NaP3 to use

Figured that would be the case. Yeah, the only thing better (besides easier to do the outgoing) is the time. I suspect, with Global they might even send them out faster than the buro does from ARRL.

I don't notice any difference between Global and when I did it all myself. Actually I upload to Global more often because I don't have to wait for a big batch and I don't have to find the time to do