开云体育

Dave, When I open DXKeeper, the "begin" and "end" labels for the time of the last QSO are flashing red. DXKeeper wants me to make corrections to the last log entry before allowing me to navigate to

Gentlemen, Just heard that DXLab's WinWarbler has implemented Kenwood's KY command for sending CW via the CAT interface. Since PowerSDR also implemented the KY command, it should be a snap to send

Hi Danny, Some time ago I went to the Microsoft Download site and downloaded IE6setup to a CD. Don't know if it has all the executables you need or if it goes back to the download center to get more

Amen Bill, Dave's SW should be studied by all aspiring SW engineers! More thanks than you'll ever know, Dave! Rob AB7CF On Sun, 24 Aug 2008 06:28:46 -0700 "Bill, W6WRT"

This is really just to test that our new mailing list is working properly. Dave AA6YQ and I have had quite a few discussions via private e-mail regarding various facets of DXLab. I can tell you first

At the suggestion of Rich W3ZJ, DXKeeper 1.1.4 introduces a QSO Capture window. This relatively modest window allows one to quickly capture and log QSOs. To "raise" this window, click the Capture

Ron PA1ZX DXForecast http://members1.chello.nl/~r.a.f.eberson/DXF

Ron, Your test got through, and welcome to the group. The reflector is just getting started so we are a very small group right now, you are a charter member. As such, you probably won't be getting

Dave, I have been trying the new capture window and like it very much. This morning, I got the run time error from CI-V commander without WinWarbler running. What I had open was CI-V commander,

Yep thats good Is't posible to use the modem and software for EA4TX rotor control? see http://www,ea4tx.com this is not a comurcial bud i run this and like it. Ron PA1ZX -----Oorspronkelijk

I'll construct a version of CI-V Commander that notes such errors in the error log rather than terminating execution. The error log information should help me track down the root cause. 73,

If there's documentation for the RS232 command set, then yes its possible. I checked the web site but didn't see this documentation. If you have it, please forward me a copy. 73, Dave,

it's use the paralel port as the printer. I can send you the program -----Oorspronkelijk bericht----- Verzonden: dinsdag 20 maart 2001 22:12 Aan: dxlab@... Onderwerp: [dxlab] Re:

Dave, Take a look at the following link http://www.ea4tx.com/index_en.htm which is some developers information on the rotor control that Ron asked about. From what I can gather it is not an RS232

Correct And his suport are great. -----Oorspronkelijk bericht----- Verzonden: dinsdag 20 maart 2001 23:54 Aan: Dxlab Onderwerp: [dxlab] ARS rotor control Dave, Take a look at the following

Rich found the documentation on their web site. Given that its a DDE interface, I'll need a copy of their software for testing. It'd be best to get the software directly from the supplier -- as a

I've added additional error trapping to this version -- hopefully the runtime error 6 crash W3ZJ's been experiencing will be replaced by an entry in the error log that helps me track down the root

Dave, When I click on a callsign in DXKeeper, obviously I have worked the guy, but the progress window does not always indicate any contact with his country. Also, I have worked 3G0Y 8 times

Without seeing your log, I can't know for sure, but my suspicion is that many of your DXKeeper log entries are missing DXCC country codess -- likely because DXView was not running when these entries

I'm not sure if DXView was open when I did the import. However, it was open when I did the recompute. I just did that again to make sure, it didn't help. However, I just noticed something else. When I