Re: Help! I think I may have just ruined my 9 year old's Chanukah
On Wed, Dec 20, 2017 at 09:23 pm, K9HZ wrote:
Follow it through with the video. ?You will isolate the problem(s). ?Its almost fool-proof. ?Make a list and we can help you fix the problem areas.?
I can't. He says that has to be working to go on. It's not.
|
Re: Help! I think I may have just ruined my 9 year old's Chanukah
Hearing it over the
time signal is why it is being suggested that you disconnect
the dipole from your main rig and temporarily replace it with
a short wire.
You won't harm the
Yaesu at he power levels being produced by the Raduino.You are
only using the Yaesu to "sniff" the output from the Raduino,
in the absence of any other RF test gear.
Bill, VK7MX
toggle quoted message
Show quoted text
On Wed, Dec 20, 2017 at 07:59 pm, Vince Vielhaber wrote:
The tuning pot is connected between ground and +5
volts. When you tune it it varies the voltage going into on of
the analog ports on the nano. That voltage is mapped and a freq
is derived from that. Then the freq info is sent to the Si chip
to make that freq happen. Without the pot connected that analog
port is floating.
If it's at 5000, I'll never hear it. That stupid time station is
way too loud. I have tried it though with the plugs still
in....only unplugging it from the LCD so I could raise it up.
Still didn't hear it.
|
Re: Help! I think I may have just ruined my 9 year old's Chanukah
Follow it through with the video. ?You will isolate the problem(s). ?Its almost fool-proof. ?Make a list and we can help you fix the problem areas.?
Dr.?William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ ? Owner - Operator Big Signal Ranch ¨C K9ZC Staunton, Illinois ? Owner ¨C Operator Villa Grand Piton - J68HZ Soufriere, St. Lucia W.I. Rent it:
email:??bill@... ?
toggle quoted message
Show quoted text
On Dec 20, 2017, at 11:15 PM, tausciam@... wrote: I just tried to start the troubleshooting video. First, it's outdated. Second, touching the antenna with a wire caused it to pop and crackle until I put it firm, but I didn't get increased noise.
This thing is just junk. I wasted my money
|
Or perhaps this one?
https://web.archive.org/web/20111018093646/http://w7zoi.net/lpf-expts/lpf-expts.html
|
Re: Help! I think I may have just ruined my 9 year old's Chanukah
I just tried to start the troubleshooting video. First, it's outdated. Second, touching the antenna with a wire caused it to pop and crackle until I put it firm, but I didn't get increased noise.
This thing is just junk. I wasted my money
|
Re: uBITX working, question about power, PTT pop, LOUD headphone output
#ubitx
Correction. PTT does nothing but the encoder button only exits the menu. The change to CW tone does not take.
Regards Simon VK3ELH?
|
Re: Help! I think I may have just ruined my 9 year old's Chanukah
On Wed, Dec 20, 2017 at 07:59 pm, Vince Vielhaber wrote:
The tuning pot is connected between ground and +5 volts. When you tune it it varies the voltage going into on of the analog ports on the nano. That voltage is mapped and a freq is derived from that. Then the freq info is sent to the Si chip to make that freq happen. Without the pot connected that analog port is floating.
If it's at 5000, I'll never hear it. That stupid time station is way too loud. I have tried it though with the plugs still in....only unplugging it from the LCD so I could raise it up. Still didn't hear it.
|
Re: uBITX How to wire key jack for paddles?
See picture for paddle wiring. Dot to ring dah to tip.
With code changes could be used for a straight key also assuming it has a mono plug. Read A6 at start up. If 5v run paddle code. If 1.6v run straight key code.
Regards
Simon VK3ELH
|
Re: Help! I think I may have just ruined my 9 year old's Chanukah
On Wed, Dec 20, 2017 at 07:59 pm, Vince Vielhaber wrote:
What do you have for an antenna on the HF rig? Can you make it just a short piece of wire?
A dipole. Not going to change anything on it though. Not going to risk my HF rig over it. But, if I can hear the frequencies when we force it to a frequency, I should be able to hear it when it's tuning, shouldn't I?
|
Re: Help! I think I may have just ruined my 9 year old's Chanukah
actually, that pic
shows 5 caps and 2 resistors. I suugest that it would be
useful in these posts if you refer to components by their
numbers on the pcb, for example C1, C6 or C5 for those closest
to the Si chip. That will narrow down the effort for those of
us looking to reply, as it is our normal mode of referring to
them.
Bill, VK7MX
On 21/12/2017 2:47 PM, William R
Maxwell wrote:
toggle quoted message
Show quoted text
Nothing obviously awry there.
Here is the
picture of the Sis chip
|
Re: Help! I think I may have just ruined my 9 year old's Chanukah
Caps look fine to
me. The two resistors can't really be seen from the at view,
as far as the solder joins closest to the Si5153 are concerned
but I would suspect that they are also OK.
toggle quoted message
Show quoted text
Do those two capacitors look bad to you? I didn't notice that
before, but where the solder should be looks cratered in that pic
|
Re: Help! I think I may have just ruined my 9 year old's Chanukah
When you have the raduino out of the case, is the display no longer connected?
If you have it connected and tune to a freq, then disconnect it that freq is lost unless the tuning pot is coming with it. It should be at either extreme 7.0 or 7.3 but I'm not 100% sure what the extremes are in that. So you'll need to check near 5.000 and 4.700 but that's not a guarantee.
The tuning pot is connected between ground and +5 volts. When you tune it it varies the voltage going into on of the analog ports on the nano. That voltage is mapped and a freq is derived from that. Then the freq info is sent to the Si chip to make that freq happen. Without the pot connected that analog port is floating.
What do you have for an antenna on the HF rig? Can you make it just a short piece of wire?
Vince.
toggle quoted message
Show quoted text
On 12/20/2017 10:46 PM, tausciam@... wrote: On Wed, Dec 20, 2017 at 07:38 pm, Vince Vielhaber wrote:
Something just occurred to me. Without the raduino connected in the
case it's still going to do something. You just won't be able to
vary the freq. So with it connected to the USB, see if Farhan's
sketch works on 12.000 - whatever freq is displayed, or somewhere
close to it.
I can't tell which frequency is displayed, but I have tuned it to a
frequency, taken it out, hooked it up to USB and then tried to find it.
I did 12,000 - displayed frequency. Never found it.
I did remove the caps. They look fine to me.
--
Michigan VHF Corp.
|
Re: Apology in advance if dumb question - How do I know my order has been captured?
I noticed mine got here fast, thank you Ash.
toggle quoted message
Show quoted text
On Dec 20, 2017, at 7:42 PM, Ashhar Farhan < farhanbox@...> wrote: Our local post office refused to handle so many orders, so the gang decided to post all the usa ones through dhl anyway so you guys can get them all before christmas. We didnt do that for europe because of their ridiculous custom duty that is invoked onky if we send it via dhl, so those stay with india post.
- f
|
|
|
Re: Help! I think I may have just ruined my 9 year old's Chanukah
On Wed, Dec 20, 2017 at 07:38 pm, Vince Vielhaber wrote:
Something just occurred to me. Without the raduino connected in the case it's still going to do something. You just won't be able to vary the freq. So with it connected to the USB, see if Farhan's sketch works on 12.000 - whatever freq is displayed, or somewhere close to it.
I can't tell which frequency is displayed, but I have tuned it to a frequency, taken it out, hooked it up to USB and then tried to find it. I did 12,000 - displayed frequency. Never found it.
?
I did remove the caps. They look fine to me.
|
Re: Ordered the 10th, no tracking number yet
There was some trouble at dhl bangalore, it has been resolved. Await the shipment details soon. - f
On 21 Dec 2017 6:58 am, "Gene Nitschke" < genenitschke@...> wrote:
Ordered on the 10th.
Received Paypal tracking on the 19th.
Received today 20th?(Upstate NY, USA)
Gene N2IJF
Hi Marco
?
Tnx for the info, But the radios are coming to UK via Royal Mail¡maybe their tracking system will show something
?
73 , Charlie GI4FUE
?
From: [email protected] [mailto:[email protected]]
On Behalf Of M Garza
Sent: 20 December 2017 21:56
To: [email protected]
Subject: Re: [BITX20] Ordered the 10th, no tracking number yet
?
This is normal if ordered via India Post.? The radio is probably sitting at customs.??
You will be able to track it via the USPS website once it gets into their possession.??
This will take a week or two.
?
On Wed, Dec 20, 2017 at 3:32 PM, Charlie Morrison <charlie@...> wrote:
Same here Phil..no movement since 15th
?
Charlie ¨C GI4FUE
?
From:
[email protected] [mailto:[email protected]]
On Behalf Of philip yates
Sent: 20 December 2017 18:58
To: [email protected]
Subject: Re: [BITX20] Ordered the 10th, no tracking number yet
?
Mines been sat with Mumbai Air since the 15th, after being inserted into bag ?
And thats as far as it has gone ? may need the helping hand of one of Santa's elves.
?
On Wed, Dec 20, 2017 at 11:16 AM, Raj vu2zap <rajendrakumargg@...> wrote:
I got the same mail one week ago, no sign of it (in India!)
At 20-12-2017, you wrote:
>I also ordered on the 10th. No indication about shipping so far although an email was returned saying it would be sent in the "next couple of days."
?
?
|
Re: Apology in advance if dumb question - How do I know my order has been captured?
Our local post office refused to handle so many orders, so the gang decided to post all the usa ones through dhl anyway so you guys can get them all before christmas. We didnt do that for europe because of their ridiculous custom duty that is invoked onky if we send it via dhl, so those stay with india post.
- f
On 21 Dec 2017 7:16 am, "William Londree" < ventura_bill@...> wrote: Mine came via DHL though I did not order carrier service. I just assumed that Ashar and the Elves were adding a bit of Seasons Spirit for the early batch to get here ahead of Christmas.
At any rate, Thank You guys for getting it here early and let me know if additional charges are required.
73s
Bill
W6SDI
|
Re: Help! I think I may have just ruined my 9 year old's Chanukah
Oh, I thought you uploaded another one. The capacitor looks ok but that doesn't mean the connection is good. Load one of the working sketches then put the raduino back in the case like you did to test this one. Push on the caps and see if anything changes.
Something just occurred to me. Without the raduino connected in the case it's still going to do something. You just won't be able to vary the freq. So with it connected to the USB, see if Farhan's sketch works on 12.000 - whatever freq is displayed, or somewhere close to it.
BTW, did you remove the two caps on the main board so you can do upper sideband? If so, did they remove cleanly - without leaving a solder short or anything.
Vince.
toggle quoted message
Show quoted text
On 12/20/2017 10:28 PM, tausciam@... wrote: I included a pic of the sis chip a couple of replies back... right
before you asked about just plugging it into usb and computer
--
Michigan VHF Corp.
|
Re: Help! I think I may have just ruined my 9 year old's Chanukah
I included a pic of the sis chip a couple of replies back... right before you asked about just plugging it into usb and computer
|
Re: Help! I think I may have just ruined my 9 year old's Chanukah
what pic?
Vince.
toggle quoted message
Show quoted text
On 12/20/2017 10:16 PM, tausciam@... wrote: Do those two capacitors look bad to you? I didn't notice that before,
but where the solder should be looks cratered in that pic
--
Michigan VHF Corp.
|
K9HZ
Joel Caulkins/N6ALT