I do have an oscilloscope. I may inject rf signals and see if they are neutralized right?

Jonathan, I would consider 5W within limits.

Let me tell you a condensed story!

My Ft757Mk2 was on 10M CW. Nice pileup. Then I heard a bad tone so I gave him a T5 and he did the same. I shut down.
I opened the rig and probed and all was fine. The rig did the same after some time.
I finally realized that the PLL lost lock and was creating noise hunting for a lock.
I found the signal in the feedback loop was low when board was hot.
I figured that the loop gain was low. I just swapped some 2SC535 as I remember from other parts of the rig and
Problem solved.

Sometimes a combination of semiconductor parts results in such situations! If everything works then we don't learn anything new!

Cheers
Raj

At 20/06/2017, you wrote:

Raj,

Thanks. Low mic gain might be it, but I thought you should get 5W out of the simple electret mic included?

And the issue is that I have to crank R136 fully over to get the 5 watts. I will short out R131 and see what happens.

JOnathan

On 6/19/2017 10:43 PM, Raj vu2zap wrote:

Could be due to any or many of the following reasons:

1: Low audio drive - very likely (I use an amped Motorola mic and it goes up to 10W)

2: Low VFO or BFO levels

3: BFO frequency may need tweaking to suit the filter or your voice.

4: Low BiDi amp stage gain - unlikely

5: Low gain in final RF amp stages - short out R131 and see

Considering you get 5W it is not really low as you think!

Cheers
Raj

At 19/06/2017, you wrote:

HI All,

My original BITX never "aligned" correctly. In order to get the 1 amp current draw when hallooo'ing into the mic I had to crank R136 all the way. In that way I could get 5 watts out but only if running higher PA voltages.

xxx snip xxx

Thanks!

Jonathan - KK6RPX

+1 on the Prusa. My nephew bought one and we assembled it. Works very well. He got the platform leveler upgrade recently. It has been working well for over a year now. He has done many big/long prints with it. And the thing is still in production, many of the lower end printers have come and gone in the last year.

Jonathan

On 6/20/2017 7:37 AM, Michael Hagen wrote:

On 6/20/2017 7:27 AM, R S via Groups.Io wrote:

Thanks. That's a lot of info to me. Will start looking in a very few minutes to what I can find.?

Again. Greatly appreciate the fast replies.?

Ron. ?

KJ4FFG?

On Tuesday, June 20, 2017, 10:14, Michael Hagen <motdog@...> wrote:

My first was the wooden box models with 2 heads.? This was 3 years ago.? $500 from So. El Monte Ca.

I made it simpler, removed a head and changed the extruder.?? Works good now.

Now I bought 2 more Hictops as kits.? I bought several extra parts as well a all metal extrusion head on eBay.

The Hictop brand on eBay is THE BEST for the money.? Get the ALL Aluminum model.? I got one because

it was repackaged and had some used parts.? At that time $229.? My friend bought several too.? Before he paid

$2k for a popular brand the doesn't make as big parts.

You can get them for about $300.?? You just can't beat them.? You have to build them.? I took days and had problems.

My friend spent a few hours!?? On a new one get 24 V PS, older was 12V like mine.? Get Auto Zero sensor too.

Some models they sold had the Z axes rods with just a simple thread.? Get the one with the Square thread.

But, I got changed mine for less than $20 by buying the Square ones and retrofitted.

I don't know about the filament counter, not needed.? They are programed with Arduino.? Just like Raduino!

I have programmed my several times, in fact I changed the whole board out when I had programming problems.

There is quite a learning curve.? There is a yahoo group and "Henry" is very helpful!

I also use Simply3D to convert STL files to print files.? Would never go back to the Free programs!

I would not like to be in the 3D printer business competing with these!? I a going to give my classic wooden box to a friend.

Mike, WA6ISP

On 6/20/2017 6:41 AM, R S via Groups.Io wrote:

What 3D printer are you folks using and sites or are they purchased locally to you? ?What are they priced at?

Thanks

Ron. KJ4FFG?

On Tuesday, June 20, 2017, 09:25, Michael Hagen <motdog@...> wrote:

I also used supports, the big Knob is hollowed out some places. I made
2, both came out perfect.? Simply3D makes me an Expert!

Takes a exacto knife to dig out the supports.

I love that program.? If you don't have a 6-32 tap, you can heat up a
long 6-32 screw (held in vice grips) and thread the holes.

Mike, WA6ISP

Raj,

Thanks. Low mic gain might be it, but I thought you should get 5W out of the simple electret mic included?

And the issue is that I have to crank R136 fully over to get the 5 watts. I will short out R131 and see what happens.

JOnathan

On 6/19/2017 10:43 PM, Raj vu2zap wrote:

Could be due to any or many of the following reasons:

1: Low audio drive - very likely (I use an amped Motorola mic and it goes up to 10W)

2: Low VFO or BFO levels

3: BFO frequency may need tweaking to suit the filter or your voice.

4: Low BiDi amp stage gain - unlikely

5: Low gain in final RF amp stages - short out R131 and see

Considering you get 5W it is not really low as you think!

Cheers
Raj

At 19/06/2017, you wrote:

HI All,

My original BITX never "aligned" correctly. In order to get the 1 amp current draw when hallooo'ing into the mic I had to crank R136 all the way. In that way I could get 5 watts out but only if running higher PA voltages.

xxx snip xxx

Thanks!

Jonathan - KK6RPX

On 6/20/2017 7:27 AM, R S via Groups.Io wrote:

Thanks. That's a lot of info to me. Will start looking in a very few minutes to what I can find.?

Again. Greatly appreciate the fast replies.?

Ron. ?

KJ4FFG?

On Tuesday, June 20, 2017, 10:14, Michael Hagen <motdog@...> wrote:

My first was the wooden box models with 2 heads.? This was 3 years ago.? $500 from So. El Monte Ca.

I made it simpler, removed a head and changed the extruder.?? Works good now.

Now I bought 2 more Hictops as kits.? I bought several extra parts as well a all metal extrusion head on eBay.

The Hictop brand on eBay is THE BEST for the money.? Get the ALL Aluminum model.? I got one because

it was repackaged and had some used parts.? At that time $229.? My friend bought several too.? Before he paid

$2k for a popular brand the doesn't make as big parts.

You can get them for about $300.?? You just can't beat them.? You have to build them.? I took days and had problems.

My friend spent a few hours!?? On a new one get 24 V PS, older was 12V like mine.? Get Auto Zero sensor too.

Some models they sold had the Z axes rods with just a simple thread.? Get the one with the Square thread.

But, I got changed mine for less than $20 by buying the Square ones and retrofitted.

I don't know about the filament counter, not needed.? They are programed with Arduino.? Just like Raduino!

I have programmed my several times, in fact I changed the whole board out when I had programming problems.

There is quite a learning curve.? There is a yahoo group and "Henry" is very helpful!

I also use Simply3D to convert STL files to print files.? Would never go back to the Free programs!

I would not like to be in the 3D printer business competing with these!? I a going to give my classic wooden box to a friend.

Mike, WA6ISP

On 6/20/2017 6:41 AM, R S via Groups.Io wrote:

What 3D printer are you folks using and sites or are they purchased locally to you? ?What are they priced at?

Thanks

Ron. KJ4FFG?

On Tuesday, June 20, 2017, 09:25, Michael Hagen <motdog@...> wrote:

I also used supports, the big Knob is hollowed out some places. I made
2, both came out perfect.? Simply3D makes me an Expert!

Takes a exacto knife to dig out the supports.

I love that program.? If you don't have a 6-32 tap, you can heat up a
long 6-32 screw (held in vice grips) and thread the holes.

Mike, WA6ISP

Hi All,

While waiting for some parts for another project, I came across some interesting code and have been doing some work on existing code by PD8W.
I have tried to contact him for some help but he does not appear to be available.
He developed some code to add a 2.8inch tft to the bitx40. ?The display is interesting and uses a rotary with the sg5351 with an atmega2560.

I have made Progress:

The display works fine.
The Vfo dial changes the sg5351 dds
When i disconnect the current raduino board and the vfo connector on my bit40, then connect my test unit, I can tune fine, no clicks or noise , reception is great.

Problem: - push buttons?

The code uses the switch on the rotary or a standard push button to change the range step ?tuning (10khz,1khz,100hz etc etc.
It uses pin 46 (atmega 2560) but I tried it on other pins as well.
I cant seem to make the button work. If i hold the wire which is connected to the pin, the range starts changing(capacitive effect I guess) ?but If i try a button it does not change the step tuning.
I have tried using _pullup command - no change.
Also tried 10k pullup resistor (pin to resistor to 5v) - no change.
Tried 10k to ground - no change.
Tried direct - to pin to button -?
Also tried other push buttons to make sure they were good.

This should be simple but I am running out of ideas.

If any one can provide a solution or some ideas to try, for this one button , it will probably solve the same issues with the remaining buttons .
Any help would be much appreciated

Joe
VE1BWV

?

#include <Adafruit_GFX.h>

#include <gfxfont.h>

#include <Fonts/FreeSansBold12pt7b.h>

#include <Fonts/FreeSerifBold12pt7b.h>

#include <Fonts/FreeSans9pt7b.h>

#include <MCUFRIEND_kbv.h>

#include <Wire.h>

#include <Rotary.h>

#include <si5351.h>

?

#define ?ROT_L1_PIN 49// rotary A

#define ?ROT_R1_PIN 48//rotaryA

#define ?LED_R_PIN 45

#define ?LED_G_PIN 44

#define ?LED_B_PIN 47

#define ROT_SW1_PIN 46// ? <<<<<<< this is the step range tuning button >>>>>>>>>>>

#define ?ROT_LEFT ?1

#define ?ROT_RIGHT 2

#define ?ROT_STAY ?3

#define ROT_MIN ? ? ? ?700000UL ? ? ? ? ? ? ? // Lower frequency limit

#define ROT_MAX ? ? ? ?5000000000UL

#define CALLSIGN "PD8W"

#define BITX40 ? "BITX40 V3c"

?

int ROT_d = 10;

int mode = 0;

int oldMode = -1;

?

Si5351 si5351;

Rotary r = Rotary(ROT_L1_PIN, ROT_R1_PIN);

volatile uint32_t LSB = 1199850000ULL;

volatile uint32_t USB = 1200150000ULL;

volatile uint32_t bfo = LSB; //start in lsb

//In this sketch the start frequency will be 7.100000 Mhz

volatile uint32_t vfo = 709980000ULL / SI5351_FREQ_MULT; //start freq - change to suit

boolean changed_f = 0;

String tbfo = "";

long lastMilis = 0; ? ? ? // to track the last sampled time

long val1a, val1b;

long dirRot1 = ROT_STAY;

long valRot1 = vfo;

long oldVal1 = -1;

//------------------------------- Set Optional Features here --------------------------------------

//Remove comment (//) from the option you want to use. Pick only one

#define IF_Offset //Output is the display plus or minus the bfo frequency

//#define Direct_conversion //What you see on display is what you get

//#define FreqX4 ?//output is four times the display frequency

//--------------------------------------------------------------------------------------------------

?

MCUFRIEND_kbv tft;

?

const int ?buttonPin = 52; ? ?// pins that ?pushbuttons are attached ?for tx/rx ? mode/ etc

const int ?buttonPin2 = 53;

const int ?buttonPin3 = 51;

const int ?buttonPin4 = 50;

const int ?buttonPin5 = 43;

?

int buttonPushCounter = 0; ? // counter for the number of button presses

int buttonPushCounter2 = 0; ? // counter for the number of button presses

int buttonPushCounter3 = 0; ? // counter for the number of button presses

int buttonPushCounter4 = 0; ? // counter for the number of button presses

int buttonPushCounter5 = 0; ? // counter for the number of button presses

?

?

int buttonState = 0; ? ? ? ? // current state of the button

int buttonState2 = 0; ? ? ? ? // current state of the button

int buttonState3 = 0; ? ? ? ? // current state of the button

int buttonState4 = 0; ? ? ? ? // current state of the button

int buttonState5 = 0; ? ? ? ? // current state of the button

?

?

int lastButtonState = 0; ? ? // previous state of the button

int lastButtonState2 = 0; ? ? // previous state of the button

int lastButtonState3 = 0; ? ? // previous state of the button

int lastButtonState4 = 0; ? ? // previous state of the button

int lastButtonState5 = 0; ? ? // previous state of the button

?

// Assign human-readable names to some common 16-bit color values:

#define BLACK ? 0x0000

#define BLUE ? ?0x0353

#define OBLUE ? 0x001F

#define RED ? ? 0xF800

#define GREEN ? 0x07E0

#define CYAN ? ?0x07FF

#define MAGENTA 0xF81F

#define YELLOW ?0xFFE0

#define WHITE ? 0xFFFF

#define GREY ? ?0x7BEF

#define DARKGREY 0x18E3

?

uint16_t g_identifier;

?

void setup(void) {

? Serial.begin(9600);

? pinMode(LED_R_PIN, OUTPUT);

? pinMode(LED_G_PIN, OUTPUT);

? pinMode(LED_B_PIN, OUTPUT);

? Wire.begin();

?

? si5351.set_correction(140); //**mine. There is a calibration sketch in File/Examples/si5351Arduino-Jason

? //where you can determine the correction by using the serial monitor.

?

? //initialize the Si5351

? si5351.init(SI5351_CRYSTAL_LOAD_8PF, 0); //If you're using a 27Mhz crystal, put in 27000000 instead of 0

? // 0 is the default crystal frequency of 25Mhz.

?

? si5351.set_pll(SI5351_PLL_FIXED, SI5351_PLLA);

? // Set CLK0 to output the starting "vfo" frequency as set above by vfo = ?

?

#ifdef IF_Offset

? uint32_t vco = bfo - (vfo * SI5351_FREQ_MULT);

? si5351.set_freq(vco, SI5351_PLL_FIXED, SI5351_CLK0);

? // seems not used : volatile uint32_t vfoT = (vfo * SI5351_FREQ_MULT) - bfo;

? tbfo = "LSB";

? // Set CLK2 to output bfo frequency

? si5351.set_freq( bfo, 0, SI5351_CLK2);

? si5351.drive_strength(SI5351_CLK0, SI5351_DRIVE_2MA); //you can set this to 2MA, 4MA, 6MA or 8MA

? //si5351.drive_strength(SI5351_CLK1,SI5351_DRIVE_2MA); //be careful though - measure into 50ohms

? //si5351.drive_strength(SI5351_CLK2,SI5351_DRIVE_2MA); //

#endif

?

#ifdef Direct_conversion

? si5351.set_freq((vfo * SI5351_FREQ_MULT), SI5351_PLL_FIXED, SI5351_CLK0);

#endif

?

#ifdef FreqX4

? si5351.set_freq((vfo * SI5351_FREQ_MULT) * 4, SI5351_PLL_FIXED, SI5351_CLK0);

#endif

?

? int i = 0;

? pinMode(ROT_L1_PIN, INPUT);

? pinMode(ROT_R1_PIN, INPUT);

? digitalWrite(ROT_L1_PIN, HIGH); //pull-up enable

? digitalWrite(ROT_R1_PIN, HIGH); //pull-up enable

?

? pinMode(ROT_SW1_PIN, INPUT); // ?non pull up ?<<<<<<<<<<<<<<<<<<< range step tuning ?button>>>>>>>>>>>>>>>>>

?

? uint32_t when = millis();

? // ? ?while (!Serial) ; ? //hangs a Leonardo until you connect a Serial

? if (!Serial) delay(5000); ? ? ? ? ? //allow some time for Leonardo

? Serial.println("Serial took " + String((millis() - when)) + "ms to start");

? static uint16_t identifier;

? // ? ?tft.reset(); ? ? ? ? ? ? ? ? //we can't read ID on 9341 until begin()

? g_identifier = tft.readID(); //

? Serial.print("ID = 0x");

? Serial.println(g_identifier, HEX);

? if (g_identifier == 0x00D3 || g_identifier == 0xD3D3) g_identifier = 0x9481; // write-only shield

? if (g_identifier == 0xFFFF) g_identifier = 0x9341; // serial

? // ? ?g_identifier = 0x9329; ? ? ? ? ? ? ? ? ? ? ? ? ? ? // force ID

? tft.begin(g_identifier);

?

#if defined(MCUFRIEND_KBV_H_)

? uint16_t scrollbuf[320]; ? ?// my biggest screen is 320x480

#define READGRAM(x, y, buf, w, h) ?tft.readGRAM(x, y, buf, w, h)

#else

? uint16_t scrollbuf[320]; ? ?// Adafruit only does 240x320

? // Adafruit can read a block by one pixel at a time

? int16_t ?READGRAM(int16_t x, int16_t y, uint16_t *block, int16_t w, int16_t h)

? {

? ? uint16_t *p;

? ? for (int row = 0; row < h; row++) {

? ? ? p = block + row * w;

? ? ? for (int col = 0; col < w; col++) {

? ? ? ? *p++ = tft.readPixel(x + col, y + row);

? ? ? }

? ? }

? }

#endif

? uint8_t aspect;

? uint16_t pixel;

? char *colorname[] = {" PD8W"};

? uint16_t colormask[] = { 0x001F, 0x7BEF, ?};

? uint16_t dx, rgb, n, s, wid, ht;

? tft.setRotation(1);

? tft.fillScreen(BLACK);

? tft.drawRect(74, 58, 71, 13, GREY);

? tft.setTextSize(1);

? tft.setCursor(77, 61);

? tft.setTextColor(GREY, BLACK);

? tft.println("WB-Software");

? tft.drawRect(74, 70, 180, 100, GREY);

? tft.fillRect(75, 70, 69, 1, BLACK);

? tft.setFont();

? tft.setCursor(91, 85);

? tft.setTextColor(CYAN, BLACK);

? tft.println("Powered and developed by");

? tft.setFont(&FreeSansBold12pt7b);

? tft.setTextSize(1);

? tft.setCursor(130, 128);

? tft.setTextColor(WHITE, BLACK);

? tft.println("PD8W ");

? tft.setFont();

? tft.setTextSize(1);

? tft.setCursor(118, 145);

? tft.setTextColor(YELLOW, BLACK);

? tft.println(" (c)");

? tft.drawRect(183, 169, 71, 13, GREY);

? tft.fillRect(183, 169, 70, 1, BLACK);

? tft.setTextSize(1);

? tft.setCursor(186, 171);

? tft.setTextColor(GREY, BLACK);

? tft.println("version 1.0");

? delay(5000);

? tft.fillScreen(BLACK);

? tft.setFont();

? aspect = (0 + 0) & 3;

? tft.setRotation(aspect + 1);

? wid = tft.width();

? ht = tft.height();

?

? dx = wid / 32;

? for (n = 0; n < 32; n++) {

? ? rgb = n * 8;

? ? rgb = tft.color565(rgb, rgb, rgb);

? ? tft.fillRect(n * dx, 10, dx, 44, rgb & colormask[aspect]);

? }

? tft.setTextSize(2);

? tft.setTextColor(colormask[aspect], BLACK);

? tft.setCursor(0, 24);

? tft.print(colorname[aspect]);

? tft.setTextColor(WHITE);

? tft.print(" BITX40");

? tft.setTextSize(1);

? tft.println(" TRANSCEIVER");

? tft.setCursor(285, 25);

? tft.println("21:45");

#if defined(MCUFRIEND_KBV_H_)

? extern const uint8_t penguin[];

? tft.setAddrWindow(240, 5, 279, 59);

? tft.pushColors(penguin, 1600, 1);

#endif

? tft.setFont();

? tft.setTextSize(1);

? tft.setTextColor(GREY, BLACK);

? tft.setCursor(265, 64);

? tft.println("- 86 dBM");

? tft.setFont(&FreeSans9pt7b);

? tft.setTextSize(1);

? tft.setCursor(20, 125);

? tft.setTextColor(RED, BLACK);

? tft.println("VFO");

? tft.setTextSize(2);

? tft.setFont(&FreeSans9pt7b);

? tft.setTextSize(1);

? tft.setCursor(29, 145);

? tft.setTextColor(CYAN, BLACK);

? tft.println("A");

? tft.setTextSize(2);

? tft.setFont(&FreeSansBold12pt7b);

? tft.setFont();

? tft.setTextSize(1);

? tft.setCursor(150, 155);

? tft.setTextColor(GREY, BLACK);

? tft.print("AGC-S");

? tft.setCursor(215, 155);

? tft.println("100 Hz");

? tft.setFont(&FreeSans9pt7b);

? tft.setTextSize(1);

? tft.setCursor(270, 145);

? tft.setTextColor(WHITE, BLACK);

? tft.println("LSB");

? tft.fillRect(20, 60, 24, 15, GREEN);

? tft.drawRect(50, 60, 24, 15, RED);

? tft.fillRect(80, 60, 28, 15, GREY);

? tft.drawRect(108, 60, 31, 15, GREY);

? tft.setFont(&FreeSans9pt7b);

? tft.setTextColor(colormask[aspect], BLACK);

? tft.setCursor(20, 71);

? tft.setFont();

? tft.setTextColor(BLACK);

? tft.println(" RX ");

? tft.setCursor(50, 64);

? tft.setTextColor(RED);

? tft.println(" TX ");

? tft.setCursor(81, 64);

? tft.setTextColor(BLACK);

? tft.println(" BW ");

? tft.setCursor(107, 63);

? tft.setTextColor(GREY);

? tft.println(" 3.0k ");

? tft.drawLine(155, 72, 160, 60, WHITE);

? tft.drawLine(176, 60, 181, 72, WHITE);

? tft.fillRect(161, 60, 15, 1, WHITE);

? tft.fillRect(148, 72, 42, 1, WHITE);

? tft.fillRect(168, 68, 1, 4, WHITE);

? tft.setCursor(39, 180);

? tft.print("S");

? tft.setCursor(59, 180);

? tft.print("1");

? tft.setCursor(84, 180);

? tft.print("3");

? tft.setCursor(110, 180);

? tft.print("5");

? tft.setCursor(136, 180);

? tft.print("7");

? tft.setCursor(162, 180);

? tft.print("9");

? tft.setTextColor(RED);

? tft.setCursor(186, 180);

? tft.print("+20");

? tft.setCursor(218, 180);

? tft.print("+40");

? tft.setCursor(250, 180);

? tft.print("+60dB");

? tft.fillRect(60, 189, 2, 3, WHITE);

? tft.fillRect(73, 189, 2, 3, WHITE);

? tft.fillRect(86, 189, 2, 3, WHITE);

? tft.fillRect(99, 189, 2, 3, WHITE);

? tft.fillRect(112, 189, 2, 3, WHITE);

? tft.fillRect(125, 189, 2, 3, WHITE);

? tft.fillRect(138, 189, 2, 3, WHITE);

? tft.fillRect(151, 189, 2, 3, WHITE);

? tft.fillRect(164, 189, 2, 3, WHITE);

? tft.fillRect(196, 189, 2, 3, RED);

? tft.fillRect(228, 189, 2, 3, RED);

? tft.fillRect(260, 189, 2, 3, RED);

? for (s = 50; s < 167; s++) {

? ? tft.fillRect(s, 192, 1, 1, WHITE);

? }

? for (s = 167; s < 271; s++) {

? ? tft.fillRect(s, 191, 1, 2, RED);

? }

? for (s = 50; s < 270; s = s + 3) {

? ? tft.fillRect(s, 193, 2, 10, GREY);

? ? tft.drawRect(s + 2, 193, 1, 10, BLACK);

? ? tft.fillRect(s, 203, 3, 1, WHITE);

? }

? for (i = 0; i < 1; i++) {

? ? tft.fillRect(50, 193, 2, 10, WHITE);

? ? for (s = 52; s <= 165; s = s + 3) {

? ? ? tft.fillRect(s, 193, 2, 10, BLUE);

? ? ? tft.drawRect(s + 2, 193, 1, 10, BLACK);

? ? ? delay(2);

? ? }

? ? tft.fillRect(50, 193, 2, 10, WHITE);

? ? for (s = 165; s <= 270; s = s + 3) {

? ? ? tft.fillRect(s, 193, 2, 10, RED);

? ? ? tft.drawRect(s + 2, 193, 1, 10, BLACK);

? ? ? delay(2);

? ? }

? ? for (s = 270; s >= 168; s = s - 3) {

? ? ? tft.fillRect(s, 193, 2, 10, GREY);

? ? ? tft.fillRect(s + 2, 193, 1, 10, BLACK);

? ? ? tft.drawRect(s - 2, 193, 2, 10, RED);

? ? ? delay(2);

? ? }

? ? tft.fillRect(166, 193, 2, 10, GREY);

? ? tft.fillRect(165, 193, 1, 10, BLACK);

? ? for (s = 164; s >= 52; s = s - 3) {

? ? ? tft.fillRect(s, 193, 2, 10, GREY);

? ? ? tft.fillRect(s + 2, 193, 1, 10, BLACK);

? ? ? tft.drawRect(s - 2, 193, 2, 10, BLUE);

? ? ? delay(2);

? ? }

? }

? for (s = 50; s < 164; s = s + 3) {

? ? tft.fillRect(s, 193, 2, 10, BLUE);

? ? tft.drawRect(s + 2, 193, 1, 10, BLACK);

? }

? for (s = 164; s < 181; s = s + 3) {

? ? tft.fillRect(s, 193, 2, 10, RED);

? ? tft.drawRect(s + 2, 193, 1, 10, BLACK);

? }

? tft.fillRect(50, 193, 2, 10, WHITE);

? tft.setCursor(30, 206);

? tft.setTextColor(GREY, BLACK);

? tft.print("Po 0");

? tft.setCursor(110, 206);

? tft.print("25");

? tft.setCursor(162, 206);

? tft.print("50");

? tft.setCursor(255, 206);

? tft.print("100%");

? tft.setCursor(0, 231);

? tft.setTextColor(YELLOW, BLACK);

? tft.setTextSize(1);

? tft.print("Version 1.0 - WB-Software (c) 2016");

? tft.print(" GPU:");

? tft.print(tft.readID(), HEX);

? tft.print("@");

? tft.print(0.000001 * F_CPU);

? tft.println("MHz");

? delay(2000);

? tft.fillRect(0, 230, 320, 10, BLACK);

? tft.fillRect(2, 225, 60, 15, DARKGREY);

? tft.drawRect(2, 225, 60, 15, GREY);

? tft.setCursor(16, 229);

? tft.setTextColor(WHITE, DARKGREY);

? tft.print("METER");

? tft.fillRect(66, 225, 60, 15, DARKGREY);

? tft.drawRect(66, 225, 60, 15, GREY);

? tft.setCursor(75, 229);

? tft.setTextColor(WHITE, DARKGREY);

? tft.print("VFO/MEM");

? tft.fillRect(130, 225, 60, 15, DARKGREY);

? tft.drawRect(130, 225, 60, 15, GREY);

? tft.setCursor(142, 229);

? tft.setTextColor(WHITE, DARKGREY);

? tft.print("SSB/CW");

? tft.fillRect(194, 225, 60, 15, DARKGREY);

? tft.drawRect(194, 225, 60, 15, GREY);

? tft.setCursor(200, 229);

? tft.setTextColor(WHITE, DARKGREY);

? tft.print("TRANSMIT");

? tft.fillRect(258, 225, 60, 15, DARKGREY);

? tft.drawRect(258, 225, 60, 15, GREY);

? tft.setCursor(271, 229);

? tft.setTextColor(WHITE, DARKGREY);

? tft.print("FILTER");

}

?

void loop(void) {

? digitalWrite(LED_R_PIN, HIGH);

? digitalWrite(LED_G_PIN, HIGH);

? digitalWrite(LED_B_PIN, LOW);

? buttonState = digitalRead(buttonPin);

? if (buttonState != lastButtonState) {

? ? if (buttonState == HIGH) {

? ? ? buttonPushCounter++;

? ? ? switch (buttonPushCounter) {

? ? ? ? case 1:

? ? ? ? ? Serial.println("4.0k");

? ? ? ? ? tft.fillRect(108, 62, 28, 10, BLACK);

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(258, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(258, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(271, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("FILTER");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(258, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(258, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(271, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("FILTER");

? ? ? ? ? tft.setCursor(107, 63);

? ? ? ? ? tft.setTextColor(GREY);

? ? ? ? ? tft.println(" 4.0k ");

? ? ? ? ? tft.drawLine(152, 72, 157, 60, WHITE);

? ? ? ? ? tft.drawLine(181, 60, 186, 72, WHITE);

? ? ? ? ? tft.drawLine(155, 72, 160, 60, BLACK);

? ? ? ? ? tft.drawLine(176, 60, 181, 72, BLACK);

? ? ? ? ? tft.drawLine(158, 72, 163, 60, BLACK);

? ? ? ? ? tft.drawLine(173, 60, 178, 72, BLACK);

? ? ? ? ? tft.fillRect(157, 60, 25, 1, WHITE);

? ? ? ? ? tft.fillRect(148, 72, 42, 1, WHITE);

? ? ? ? ? tft.fillRect(168, 68, 1, 4, WHITE);

? ? ? ? ? tft.fillRect(80, 78, 60, 2, GREY);

? ? ? ? ? delay(500);

? ? ? ? ? tft.fillRect(80, 78, 60, 2, BLACK);

? ? ? ? ? break;

? ? ? ? case 2:

? ? ? ? ? Serial.println("1.8k");

? ? ? ? ? tft.fillRect(108, 62, 28, 10, BLACK);

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(258, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(258, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(271, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("FILTER");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(258, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(258, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(271, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("FILTER");

? ? ? ? ? tft.setCursor(107, 63);

? ? ? ? ? tft.setTextColor(GREY);

? ? ? ? ? tft.println(" 1.8k ");

? ? ? ? ? tft.drawLine(160, 72, 165, 60, WHITE);

? ? ? ? ? tft.drawLine(171, 60, 176, 72, WHITE);

? ? ? ? ? tft.fillRect(157, 60, 25, 1, BLACK);

? ? ? ? ? tft.drawLine(152, 72, 157, 60, BLACK);

? ? ? ? ? tft.drawLine(181, 60, 186, 72, BLACK);

? ? ? ? ? tft.drawLine(155, 72, 160, 60, BLACK);

? ? ? ? ? tft.drawLine(176, 60, 181, 72, BLACK);

? ? ? ? ? tft.drawLine(158, 72, 163, 60, BLACK);

? ? ? ? ? tft.drawLine(173, 60, 178, 72, BLACK);

? ? ? ? ? tft.fillRect(165, 60, 6, 1, WHITE);

? ? ? ? ? tft.fillRect(148, 72, 42, 1, WHITE);

? ? ? ? ? tft.fillRect(168, 68, 1, 4, WHITE);

? ? ? ? ? tft.fillRect(80, 78, 60, 2, GREY);

? ? ? ? ? delay(500);

? ? ? ? ? tft.fillRect(80, 78, 60, 2, BLACK);

? ? ? ? ? break;

? ? ? ? case 3:

? ? ? ? ? Serial.println("2.4k");

? ? ? ? ? tft.fillRect(108, 62, 28, 10, BLACK);

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(258, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(258, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(271, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("FILTER");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(258, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(258, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(271, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("FILTER");

? ? ? ? ? tft.setCursor(107, 63);

? ? ? ? ? tft.setTextColor(GREY);

? ? ? ? ? tft.println(" 2.4k ");

? ? ? ? ? tft.drawLine(158, 72, 163, 60, WHITE);

? ? ? ? ? tft.drawLine(173, 60, 178, 72, WHITE);

? ? ? ? ? tft.drawLine(160, 72, 165, 60, BLACK);

? ? ? ? ? tft.drawLine(171, 60, 176, 72, BLACK);

? ? ? ? ? tft.fillRect(157, 60, 25, 1, BLACK);

? ? ? ? ? tft.drawLine(152, 72, 157, 60, BLACK);

? ? ? ? ? tft.drawLine(181, 60, 186, 72, BLACK);

? ? ? ? ? tft.drawLine(155, 72, 160, 60, BLACK);

? ? ? ? ? tft.drawLine(176, 60, 181, 72, BLACK);

? ? ? ? ? tft.fillRect(163, 60, 10, 1, WHITE);

? ? ? ? ? tft.fillRect(148, 72, 42, 1, WHITE);

? ? ? ? ? tft.fillRect(168, 68, 1, 4, WHITE);

? ? ? ? ? tft.fillRect(80, 78, 60, 2, GREY);

? ? ? ? ? delay(500);

? ? ? ? ? tft.fillRect(80, 78, 60, 2, BLACK);

? ? ? ? ? break;

? ? ? ? case 4:

? ? ? ? ? Serial.println("3.0k");

? ? ? ? ? tft.fillRect(108, 62, 28, 10, BLACK);

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(258, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(258, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(271, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("FILTER");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(258, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(258, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(271, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("FILTER");

? ? ? ? ? tft.setCursor(107, 63);

? ? ? ? ? tft.setTextColor(GREY);

? ? ? ? ? tft.println(" 3.0k ");

? ? ? ? ? tft.drawLine(155, 72, 160, 60, WHITE);

? ? ? ? ? tft.drawLine(176, 60, 181, 72, WHITE);

? ? ? ? ? tft.drawLine(158, 72, 163, 60, BLACK);

? ? ? ? ? tft.drawLine(173, 60, 178, 72, BLACK);

? ? ? ? ? tft.drawLine(160, 72, 165, 60, BLACK);

? ? ? ? ? tft.drawLine(171, 60, 176, 72, BLACK);

? ? ? ? ? tft.fillRect(157, 60, 25, 1, BLACK);

? ? ? ? ? tft.drawLine(152, 72, 157, 60, BLACK);

? ? ? ? ? tft.drawLine(181, 60, 186, 72, BLACK);

? ? ? ? ? tft.fillRect(161, 60, 15, 1, WHITE);

? ? ? ? ? tft.fillRect(148, 72, 42, 1, WHITE);

? ? ? ? ? tft.fillRect(168, 68, 1, 4, WHITE);

? ? ? ? ? tft.fillRect(80, 78, 60, 2, GREY);

? ? ? ? ? delay(500);

? ? ? ? ? tft.fillRect(80, 78, 60, 2, BLACK);

? ? ? ? ? buttonPushCounter = 0;

? ? ? ? ? break;

? ? ? }

? ? } else {

? ? ? // if the current state is LOW then the button

? ? ? // wend from on to off:

? ? }

? ? // Delay a little bit to avoid bouncing

? ? delay(50);

? }

?

? buttonState2 = digitalRead(buttonPin2);

? if (buttonState2 != lastButtonState2) {

? ? if (buttonState2 == HIGH) {

? ? ? buttonPushCounter2++;

? ? ? switch (buttonPushCounter2) {

? ? ? ? case 1:

? ? ? ? ? Serial.print("TX: button ");

? ? ? ? ? Serial.println(buttonPushCounter2);

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(194, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(194, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(200, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("TRANSMIT");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(194, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(194, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(200, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("TRANSMIT");

? ? ? ? ? tft.fillRect(50, 60, 24, 15, RED);

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.setCursor(50, 64);

? ? ? ? ? tft.setTextColor(WHITE);

? ? ? ? ? tft.println(" TX ");

? ? ? ? ? tft.fillRect(20, 60, 24, 15, BLACK);

? ? ? ? ? tft.drawRect(20, 60, 24, 15, GREEN);

? ? ? ? ? tft.setTextColor(GREEN);

? ? ? ? ? tft.setCursor(20, 64);

? ? ? ? ? tft.println(" RX ");

? ? ? ? ? tft.fillRect(18, 78, 100, 10, BLACK);

? ? ? ? ? tft.setCursor(20, 80);

? ? ? ? ? tft.setTextColor(RED);

? ? ? ? ? tft.println("Transmitting");

? ? ? ? ? break;

? ? ? ? case 2:

? ? ? ? ? Serial.println("RX");

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(194, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(194, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(200, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("TRANSMIT");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(194, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(194, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(200, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("TRANSMIT");

? ? ? ? ? tft.fillRect(20, 60, 24, 15, BLACK);

? ? ? ? ? tft.fillRect(20, 60, 24, 15, GREEN);

? ? ? ? ? tft.fillRect(50, 60, 24, 15, BLACK);

? ? ? ? ? tft.drawRect(50, 60, 24, 15, RED);

? ? ? ? ? tft.setTextColor(RED);

? ? ? ? ? tft.setCursor(50, 64);

? ? ? ? ? tft.println(" TX ");

? ? ? ? ? tft.setCursor(20, 64);

? ? ? ? ? tft.setTextColor(BLACK);

? ? ? ? ? tft.println(" RX ");

? ? ? ? ? tft.fillRect(18, 78, 100, 10, BLACK);

? ? ? ? ? tft.setCursor(20, 80);

? ? ? ? ? tft.setTextColor(GREEN);

? ? ? ? ? tft.println("Receiving");

? ? ? ? ? delay(1000);

? ? ? ? ? tft.fillRect(18, 78, 100, 10, BLACK);

? ? ? ? ? buttonPushCounter2 = 0;

? ? ? ? ? break;

? ? ? }

? ? } else {

? ? ? // if the current state is LOW then the button

? ? ? // wend from on to off:

? ? }

? ? // Delay a little bit to avoid bouncing

? ? delay(50);

? }

?

? buttonState3 = digitalRead(buttonPin3);

? if (buttonState3 != lastButtonState3) {

? ? if (buttonState3 == HIGH) {

? ? ? buttonPushCounter3++;

? ? ? switch (buttonPushCounter3) {

? ? ? ? case 1:

? ? ? ? ? Serial.println("USB");

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(130, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(130, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(142, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("SSB/CW");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(130, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(130, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(142, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("SSB/CW");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(269, 130, 44, 18, BLACK);

? ? ? ? ? tft.setFont(&FreeSans9pt7b);

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.setCursor(270, 145);

? ? ? ? ? tft.setTextColor(WHITE, BLACK);

? ? ? ? ? tft.println("USB");

? ? ? ? ? break;

? ? ? ? case 2:

? ? ? ? ? Serial.println("CW");

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(130, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(130, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(142, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("SSB/CW");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(130, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(130, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(142, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("SSB/CW");

? ? ? ? ? tft.fillRect(269, 130, 44, 18, BLACK);

? ? ? ? ? tft.setFont(&FreeSans9pt7b);

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.setCursor(270, 145);

? ? ? ? ? tft.setTextColor(WHITE, BLACK);

? ? ? ? ? tft.println("CW");

? ? ? ? ? break;

? ? ? ? case 3:

? ? ? ? ? Serial.println("LSB");

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(130, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(130, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(142, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("SSB/CW");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(130, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(130, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(142, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("SSB/CW");

? ? ? ? ? tft.fillRect(269, 130, 44, 18, BLACK);

? ? ? ? ? tft.setFont(&FreeSans9pt7b);

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.setCursor(270, 145);

? ? ? ? ? tft.setTextColor(WHITE, BLACK);

? ? ? ? ? tft.println("LSB");

? ? ? ? ? buttonPushCounter3 = 0;

? ? ? ? ? break;

? ? ? ? default:

? ? ? ? ? // if nothing else matches, do the default

? ? ? ? ? // default is optional

? ? ? ? ? break;

? ? ? }

? ? } else {

? ? ? // if the current state is LOW then the button

? ? ? // wend from on to off:

? ? }

? ? // Delay a little bit to avoid bouncing

? ? delay(50);

?

? }

?

? buttonState4 = digitalRead(buttonPin4);

? if (buttonState4 != lastButtonState4) {

? ? if (buttonState4 == HIGH) {

? ? ? buttonPushCounter4++;

? ? ? switch (buttonPushCounter4) {

? ? ? ? case 1:

? ? ? ? ? Serial.println("VFO B");

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(66, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(66, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(75, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("VFO/MEM");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(66, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(66, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(75, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("VFO/MEM");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(20, 108, 40, 20, BLACK);

? ? ? ? ? tft.fillRect(20, 128, 40, 25, BLACK);

? ? ? ? ? tft.setFont(&FreeSans9pt7b);

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.setCursor(20, 125);

? ? ? ? ? tft.setTextColor(RED, BLACK);

? ? ? ? ? tft.println("VFO");

? ? ? ? ? tft.setTextSize(2);

? ? ? ? ? tft.setFont(&FreeSans9pt7b);

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.setCursor(29, 145);

? ? ? ? ? tft.setTextColor(CYAN, BLACK);

? ? ? ? ? tft.println("B");

? ? ? ? ? break;

? ? ? ? case 2:

? ? ? ? ? Serial.println("MEM");

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(66, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(66, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(75, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("VFO/MEM");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(66, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(66, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(75, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("VFO/MEM");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(20, 108, 40, 20, BLACK);

? ? ? ? ? tft.fillRect(20, 128, 40, 25, BLACK);

? ? ? ? ? tft.setFont(&FreeSans9pt7b);

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.setCursor(20, 125);

? ? ? ? ? tft.setTextColor(YELLOW, BLACK);

? ? ? ? ? tft.println("MEM");

? ? ? ? ? tft.setTextSize(2);

? ? ? ? ? tft.setFont(&FreeSans9pt7b);

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.setCursor(29, 145);

? ? ? ? ? tft.setTextColor(WHITE, BLACK);

? ? ? ? ? tft.println("001");

? ? ? ? ? break;

? ? ? ? case 3:

? ? ? ? ? Serial.println("VFO A");

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(66, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(66, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(75, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("VFO/MEM");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(66, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(66, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(75, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("VFO/MEM");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(20, 108, 40, 20, BLACK);

? ? ? ? ? tft.fillRect(20, 128, 40, 20, BLACK);

? ? ? ? ? tft.setFont(&FreeSans9pt7b);

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.setCursor(20, 125);

? ? ? ? ? tft.setTextColor(RED, BLACK);

? ? ? ? ? tft.println("VFO");

? ? ? ? ? tft.setTextSize(2);

? ? ? ? ? tft.setFont(&FreeSans9pt7b);

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.setCursor(29, 145);

? ? ? ? ? tft.setTextColor(CYAN, BLACK);

? ? ? ? ? tft.println("A");

? ? ? ? ? buttonPushCounter4 = 0;

? ? ? ? ? break;

? ? ? ? default:

? ? ? ? ? // if nothing else matches, do the default

? ? ? ? ? // default is optional

? ? ? ? ? break;

? ? ? }

? ? } else {

? ? ? // if the current state is LOW then the button

? ? ? // wend from on to off:

? ? }

? ? // Delay a little bit to avoid bouncing

? ? delay(50);

?

? }

?

? buttonState5 = digitalRead(buttonPin5);

? if (buttonState5 != lastButtonState5) {

? ? if (buttonState5 == HIGH) {

? ? ? buttonPushCounter5++;

? ? ? int s = 0;

? ? ? int t = 0;

? ? ? int i = 0;

? ? ? switch (buttonPushCounter5) {

? ? ? ? case 1:

? ? ? ? ? Serial.println("SWR");

? ? ? ? ? tft.fillRect(23, 173, 260, 40, BLACK);

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(16, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("METER");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(2, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(16, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("METER");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(78, 197, 1, 5, WHITE);

? ? ? ? ? tft.fillRect(108, 197, 1, 5, WHITE);

? ? ? ? ? tft.fillRect(134, 197, 1, 5, WHITE);

? ? ? ? ? tft.fillRect(164, 197, 1, 5, WHITE);

? ? ? ? ? tft.setCursor(28, 194);

? ? ? ? ? tft.setTextColor(GREY, BLACK);

? ? ? ? ? tft.fillRect(50, 193, 2, 10, WHITE);

? ? ? ? ? tft.print("SWR");

? ? ? ? ? for (s = 50; s < 270; s = s + 2) {

? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, GREY);

? ? ? ? ? ? tft.drawRect(s + 2, 193, 1, 10, BLACK);

? ? ? ? ? ? tft.fillRect(s, 203, 2, 1, WHITE);

? ? ? ? ? }

? ? ? ? ? tft.fillRect(78, 197, 1, 5, WHITE);

? ? ? ? ? tft.fillRect(108, 197, 1, 5, WHITE);

? ? ? ? ? tft.fillRect(134, 197, 1, 5, WHITE);

? ? ? ? ? tft.fillRect(164, 197, 1, 5, WHITE);

? ? ? ? ? tft.setCursor(48, 206);

? ? ? ? ? tft.print("1");

? ? ? ? ? tft.setCursor(70, 206);

? ? ? ? ? tft.print("1.5");

? ? ? ? ? tft.setCursor(105, 206);

? ? ? ? ? tft.print("2");

? ? ? ? ? tft.setCursor(125, 206);

? ? ? ? ? tft.print("2.5");

? ? ? ? ? tft.setCursor(162, 206);

? ? ? ? ? tft.print("3");

? ? ? ? ? tft.drawCircle(260, 208, 3, GREY);

? ? ? ? ? tft.drawCircle(266, 208, 3, GREY);

? ? ? ? ? for (i = 0; i < 2; i++) {

? ? ? ? ? ? for (s = 50; s < 70; s = s + 2) {

? ? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, BLUE);

? ? ? ? ? ? ? tft.drawRect(s + 1, 193, 1, 10, BLACK);

? ? ? ? ? ? ? tft.fillRect(50, 193, 1, 10, WHITE);

? ? ? ? ? ? ? delay(15);

? ? ? ? ? ? }

? ? ? ? ? ? for (s = 70; s >= 50; s = s - 2) {

? ? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, GREY);

? ? ? ? ? ? ? tft.fillRect(s + 1, 193, 1, 10, BLACK);

? ? ? ? ? ? ? tft.drawRect(s - 1, 193, 1, 10, BLUE);

? ? ? ? ? ? ? tft.fillRect(50, 193, 1, 10, WHITE);

? ? ? ? ? ? ? tft.fillRect(78, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(108, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(134, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(164, 197, 1, 5, WHITE);

? ? ? ? ? ? ? delay(15);

? ? ? ? ? ? }

? ? ? ? ? ? for (s = 50; s < 90; s = s + 2) {

? ? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, BLUE);

? ? ? ? ? ? ? tft.drawRect(s + 1, 193, 1, 10, BLACK);

? ? ? ? ? ? ? tft.fillRect(50, 193, 1, 10, WHITE);

? ? ? ? ? ? ? tft.fillRect(78, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(108, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(134, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(164, 197, 1, 5, WHITE);

? ? ? ? ? ? ? delay(15);

? ? ? ? ? ? }

? ? ? ? ? ? for (s = 90; s >= 50; s = s - 2) {

? ? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, GREY);

? ? ? ? ? ? ? tft.fillRect(s + 1, 193, 1, 10, BLACK);

? ? ? ? ? ? ? tft.drawRect(s - 1, 193, 1, 10, BLUE);

? ? ? ? ? ? ? tft.fillRect(50, 193, 1, 10, WHITE);

? ? ? ? ? ? ? tft.fillRect(78, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(108, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(134, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(164, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(78, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(108, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(134, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(164, 197, 1, 5, WHITE);

? ? ? ? ? ? ? delay(15);

? ? ? ? ? ? }

? ? ? ? ? }

? ? ? ? ? break;

? ? ? ? case 2:

? ? ? ? ? Serial.println("ALC");

? ? ? ? ? tft.fillRect(23, 173, 260, 40, BLACK);

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(16, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("METER");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(2, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(16, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("METER");

? ? ? ? ? delay(100);

? ? ? ? ? tft.setCursor(28, 194);

? ? ? ? ? tft.setTextColor(GREY, BLACK);

? ? ? ? ? tft.print("ALC");

? ? ? ? ? for (s = 50; s < 270; s = s + 2) {

? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, GREY);

? ? ? ? ? ? tft.drawRect(s + 2, 193, 1, 10, BLACK);

? ? ? ? ? }

? ? ? ? ? tft.fillRect(50, 203, 116, 2, RED);

? ? ? ? ? for (i = 0; i < 2; i++) {

? ? ? ? ? ? for (s = 50; s < 166; s = s + 2) {

? ? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, BLUE);

? ? ? ? ? ? ? tft.drawRect(s + 1, 193, 1, 10, BLACK);

? ? ? ? ? ? ? delay(5);

? ? ? ? ? ? }

? ? ? ? ? ? for (s = 166; s >= 50; s = s - 2) {

?

? ? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, GREY);

? ? ? ? ? ? ? tft.fillRect(s + 1, 193, 1, 10, BLACK);

? ? ? ? ? ? ? tft.drawRect(s - 1, 193, 1, 10, BLUE);

? ? ? ? ? ? ? delay(5);

? ? ? ? ? ? }

? ? ? ? ? }

? ? ? ? ? break;

? ? ? ? case 3:

? ? ? ? ? Serial.println("COMP");

? ? ? ? ? tft.fillRect(23, 173, 260, 40, BLACK);

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(16, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("METER");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(2, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(16, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("METER");

? ? ? ? ? delay(100);

? ? ? ? ? tft.setCursor(23, 194);

? ? ? ? ? tft.setTextColor(GREY, BLACK);

? ? ? ? ? tft.print("COMP");

? ? ? ? ? for (s = 50; s < 270; s = s + 2) {

? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, GREY);

? ? ? ? ? ? tft.drawRect(s + 2, 193, 1, 10, BLACK);

? ? ? ? ? }

? ? ? ? ? tft.fillRect(50, 192, 9, 12, GREY);

? ? ? ? ? tft.setTextColor(BLACK, GREY);

? ? ? ? ? tft.setCursor(52, 195);

? ? ? ? ? tft.print("0");

? ? ? ? ? tft.fillRect(88, 192, 9, 12, GREY);

? ? ? ? ? tft.setCursor(90, 195);

? ? ? ? ? tft.print("5");

? ? ? ? ? tft.fillRect(130, 192, 13, 12, GREY);

? ? ? ? ? tft.setCursor(130, 195);

? ? ? ? ? tft.print("10");

? ? ? ? ? tft.fillRect(170, 192, 13, 12, GREY);

? ? ? ? ? tft.setCursor(170, 195);

? ? ? ? ? tft.print("15");

? ? ? ? ? tft.fillRect(211, 192, 14, 12, GREY);

? ? ? ? ? tft.setCursor(212, 195);

? ? ? ? ? tft.print("20");

? ? ? ? ? tft.fillRect(256, 192, 13, 12, GREY);

? ? ? ? ? tft.setCursor(257, 195);

? ? ? ? ? tft.print("dB");

? ? ? ? ? for (i = 0; i < 3; i++) {

? ? ? ? ? ? for (s = 60; s <= 86; s = s + 2) {

? ? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, BLUE);

? ? ? ? ? ? ? tft.drawRect(s + 1, 193, 1, 10, BLACK);

? ? ? ? ? ? ? delay(7);

? ? ? ? ? ? }

? ? ? ? ? ? for (s = 98; s <= 128; s = s + 2) {

? ? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, BLUE);

? ? ? ? ? ? ? tft.drawRect(s + 1, 193, 1, 10, BLACK);

? ? ? ? ? ? ? delay(7);

? ? ? ? ? ? }

? ? ? ? ? ? for (s = 128; s >= 96; s = s - 2) {

? ? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, GREY);

? ? ? ? ? ? ? tft.fillRect(s + 1, 193, 1, 10, BLACK);

? ? ? ? ? ? ? tft.drawRect(s - 1, 193, 1, 10, BLUE);

? ? ? ? ? ? ? delay(7);

? ? ? ? ? ? }

? ? ? ? ? ? for (s = 86; s >= 58; s = s - 2) {

? ? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, GREY);

? ? ? ? ? ? ? tft.fillRect(s + 1, 193, 1, 10, BLACK);

? ? ? ? ? ? ? tft.drawRect(s - 1, 193, 1, 10, BLUE);

? ? ? ? ? ? ? delay(7);

? ? ? ? ? ? }

? ? ? ? ? ? tft.setCursor(52, 195);

? ? ? ? ? ? tft.print("0");

? ? ? ? ? ? tft.fillRect(88, 192, 9, 12, GREY);

? ? ? ? ? ? tft.setCursor(90, 195);

? ? ? ? ? ? tft.print("5");

? ? ? ? ? ? tft.fillRect(130, 192, 13, 12, GREY);

? ? ? ? ? ? tft.setCursor(130, 195);

? ? ? ? ? ? tft.print("10");

? ? ? ? ? ? tft.fillRect(170, 192, 13, 12, GREY);

? ? ? ? ? ? tft.setCursor(170, 195);

? ? ? ? ? ? tft.print("15");

? ? ? ? ? ? tft.fillRect(211, 192, 14, 12, GREY);

? ? ? ? ? ? tft.setCursor(212, 195);

? ? ? ? ? ? tft.print("20");

? ? ? ? ? ? tft.fillRect(256, 192, 13, 12, GREY);

? ? ? ? ? ? tft.setCursor(257, 195);

? ? ? ? ? ? tft.print("dB");

? ? ? ? ? }

? ? ? ? ? break;

? ? ? ? case 4:

? ? ? ? ? Serial.println("ID");

? ? ? ? ? tft.fillRect(23, 173, 260, 40, BLACK);

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(16, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("METER");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(2, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(16, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("METER");

? ? ? ? ? delay(100);

? ? ? ? ? tft.setCursor(28, 194);

? ? ? ? ? tft.setTextColor(GREY, BLACK);

? ? ? ? ? tft.fillRect(50, 193, 2, 10, WHITE);

? ? ? ? ? tft.print("ID");

? ? ? ? ? for (s = 50; s < 270; s = s + 2) {

? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, GREY);

? ? ? ? ? ? tft.drawRect(s + 2, 193, 1, 10, BLACK);

? ? ? ? ? ? tft.fillRect(s, 203, 2, 1, WHITE);

? ? ? ? ? }

? ? ? ? ? tft.setCursor(48, 206);

? ? ? ? ? tft.print("0");

? ? ? ? ? tft.setCursor(90, 206);

? ? ? ? ? tft.print("5");

? ? ? ? ? tft.setCursor(130, 206);

? ? ? ? ? tft.print("10");

? ? ? ? ? tft.setCursor(172, 206);

? ? ? ? ? tft.print("20");

? ? ? ? ? tft.setCursor(216, 206);

? ? ? ? ? tft.print("15");

? ? ? ? ? tft.setCursor(260, 206);

? ? ? ? ? tft.print("25A");

? ? ? ? ? tft.fillCircle(58, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(66, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(74, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(82, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(100, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(108, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(116, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(124, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(144, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(152, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(160, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(168, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(187, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(195, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(203, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(211, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(231, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(239, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(247, 209, 1, GREY);

? ? ? ? ? tft.fillCircle(255, 209, 1, GREY);

? ? ? ? ? tft.fillRect(92, 197, 1, 5, WHITE);

? ? ? ? ? tft.fillRect(136, 197, 1, 5, WHITE);

? ? ? ? ? tft.fillRect(178, 197, 1, 5, WHITE);

? ? ? ? ? tft.fillRect(222, 197, 1, 5, WHITE);

? ? ? ? ? tft.fillRect(264, 197, 1, 5, WHITE);

? ? ? ? ? for (i = 0; i < 1; i++) {

? ? ? ? ? ? for (s = 50; s < 170; s = s + 2) {

? ? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, BLUE);

? ? ? ? ? ? ? tft.drawRect(s + 1, 193, 1, 10, BLACK);

? ? ? ? ? ? ? delay(15);

? ? ? ? ? ? ? tft.fillRect(50, 193, 1, 10, WHITE);

? ? ? ? ? ? ? tft.fillRect(92, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(136, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(178, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(222, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(264, 197, 1, 5, WHITE);

? ? ? ? ? ? }

? ? ? ? ? ? delay(1000);

? ? ? ? ? ? for (s = 170; s >= 50; s = s - 2) {

?

? ? ? ? ? ? ? tft.fillRect(s, 193, 1, 10, GREY);

? ? ? ? ? ? ? tft.fillRect(s + 1, 193, 1, 10, BLACK);

? ? ? ? ? ? ? tft.drawRect(s - 1, 193, 1, 10, BLUE);

? ? ? ? ? ? ? delay(15);

? ? ? ? ? ? ? tft.fillRect(50, 193, 1, 10, WHITE);

? ? ? ? ? ? ? tft.fillRect(92, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(136, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(178, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(222, 197, 1, 5, WHITE);

? ? ? ? ? ? ? tft.fillRect(264, 197, 1, 5, WHITE);

? ? ? ? ? ? }

? ? ? ? ? }

? ? ? ? ? break;

? ? ? ? case 5:

? ? ? ? ? Serial.println("S/PO");

? ? ? ? ? tft.fillRect(23, 180, 260, 40, BLACK);

? ? ? ? ? tft.setFont();

? ? ? ? ? tft.setTextColor(GREY, BLACK);

? ? ? ? ? tft.setTextSize(1);

? ? ? ? ? tft.fillRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.drawRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(16, 229);

? ? ? ? ? tft.setTextColor(DARKGREY, GREY);

? ? ? ? ? tft.print("METER");

? ? ? ? ? delay(100);

? ? ? ? ? tft.fillRect(2, 225, 60, 15, DARKGREY);

? ? ? ? ? tft.drawRect(2, 225, 60, 15, GREY);

? ? ? ? ? tft.setCursor(16, 229);

? ? ? ? ? tft.setTextColor(WHITE, DARKGREY);

? ? ? ? ? tft.print("METER");

? ? ? ? ? delay(100);

? ? ? ? ? tft.setCursor(39, 180);

? ? ? ? ? tft.print("S");

? ? ? ? ? tft.setCursor(59, 180);

? ? ? ? ? tft.print("1");

? ? ? ? ? tft.setCursor(84, 180);

? ? ? ? ? tft.print("3");

? ? ? ? ? tft.setCursor(110, 180);

? ? ? ? ? tft.print("5");

? ? ? ? ? tft.setCursor(136, 180);

? ? ? ? ? tft.print("7");

? ? ? ? ? tft.setCursor(162, 180);

? ? ? ? ? tft.print("9");

? ? ? ? ? tft.setTextColor(RED);

? ? ? ? ? tft.setCursor(186, 180);

? ? ? ? ? tft.print("+20");

? ? ? ? ? tft.setCursor(218, 180);

? ? ? ? ? tft.print("+40");

? ? ? ? ? tft.setCursor(250, 180);

? ? ? ? ? tft.print("+60dB");

? ? ? ? ? tft.fillRect(60, 189, 2, 3, WHITE);

? ? ? ? ? tft.fillRect(73, 189, 2, 3, WHITE);

? ? ? ? ? tft.fillRect(86, 189, 2, 3, WHITE);

? ? ? ? ? tft.fillRect(99, 189, 2, 3, WHITE);

? ? ? ? ? tft.fillRect(112, 189, 2, 3, WHITE);

? ? ? ? ? tft.fillRect(125, 189, 2, 3, WHITE);

? ? ? ? ? tft.fillRect(138, 189, 2, 3, WHITE);

? ? ? ? ? tft.fillRect(151, 189, 2, 3, WHITE);

? ? ? ? ? tft.fillRect(164, 189, 2, 3, WHITE);

? ? ? ? ? tft.fillRect(196, 189, 2, 3, RED);

? ? ? ? ? tft.fillRect(228, 189, 2, 3, RED);

? ? ? ? ? tft.fillRect(260, 189, 2, 3, RED);

? ? ? ? ? for (s = 50; s < 167; s++) {

? ? ? ? ? ? tft.fillRect(s, 193, 1, 1, WHITE);

? ? ? ? ? }

? ? ? ? ? for (s = 166; s <= 271; s++) {

? ? ? ? ? ? tft.fillRect(s, 192, 1, 2, RED);

? ? ? ? ? }

? ? ? ? ? for (s = 50; s < 270; s = s + 3) {

? ? ? ? ? ? tft.fillRect(s, 193, 2, 10, GREY);

? ? ? ? ? ? tft.drawRect(s + 2, 200, 1, 10, BLACK);

? ? ? ? ? ? tft.fillRect(s, 203, 3, 1, WHITE);

? ? ? ? ? }

? ? ? ? ? tft.fillRect(50, 193, 2, 10, WHITE);

? ? ? ? ? tft.setCursor(30, 206);

? ? ? ? ? tft.setTextColor(GREY, BLACK);

? ? ? ? ? tft.print("Po 0");

? ? ? ? ? tft.setCursor(110, 206);

? ? ? ? ? tft.print("25");

? ? ? ? ? tft.setCursor(162, 206);

? ? ? ? ? tft.print("50");

? ? ? ? ? tft.setCursor(255, 206);

? ? ? ? ? tft.print("100%");

? ? ? ? ? for (i = 0; i < 1; i++) {

? ? ? ? ? ? tft.fillRect(50, 193, 2, 10, WHITE);

? ? ? ? ? ? for (s = 52; s <= 165; s = s + 3) {

? ? ? ? ? ? ? tft.fillRect(s, 193, 2, 10, BLUE);

? ? ? ? ? ? ? tft.drawRect(s + 2, 193, 1, 10, BLACK);

? ? ? ? ? ? ? delay(3);

? ? ? ? ? ? }

? ? ? ? ? ? tft.fillRect(50, 193, 2, 10, WHITE);

? ? ? ? ? ? for (s = 165; s <= 270; s = s + 3) {

? ? ? ? ? ? ? tft.fillRect(s, 193, 2, 10, RED);

? ? ? ? ? ? ? tft.drawRect(s + 2, 193, 1, 10, BLACK);

? ? ? ? ? ? ? delay(3);

? ? ? ? ? ? }

? ? ? ? ? ? for (s = 270; s >= 168; s = s - 3) {

? ? ? ? ? ? ? tft.fillRect(s, 193, 2, 10, GREY);

? ? ? ? ? ? ? tft.fillRect(s + 2, 193, 1, 10, BLACK);

? ? ? ? ? ? ? tft.drawRect(s - 2, 193, 2, 10, RED);

? ? ? ? ? ? ? delay(3);

? ? ? ? ? ? }

? ? ? ? ? ? tft.fillRect(166, 193, 2, 10, GREY);

? ? ? ? ? ? tft.fillRect(165, 193, 1, 10, BLACK);

? ? ? ? ? ? for (s = 164; s >= 52; s = s - 3) {

? ? ? ? ? ? ? tft.fillRect(s, 193, 2, 10, GREY);

? ? ? ? ? ? ? tft.fillRect(s + 2, 193, 1, 10, BLACK);

? ? ? ? ? ? ? tft.drawRect(s - 2, 193, 2, 10, BLUE);

? ? ? ? ? ? ? delay(3);

? ? ? ? ? ? }

? ? ? ? ? }

? ? ? ? ? for (s = 50; s < 164; s = s + 3) {

? ? ? ? ? ? tft.fillRect(50, 193, 2, 10, WHITE);

? ? ? ? ? ? tft.fillRect(s, 193, 2, 10, BLUE);

? ? ? ? ? ? tft.drawRect(s + 2, 193, 1, 10, BLACK);

? ? ? ? ? ? delay(3);

? ? ? ? ? }

? ? ? ? ? for (s = 164; s < 181; s = s + 3) {

? ? ? ? ? ? tft.fillRect(50, 193, 2, 10, WHITE);

? ? ? ? ? ? tft.fillRect(s, 193, 2, 10, RED);

? ? ? ? ? ? tft.drawRect(s + 2, 193, 1, 10, BLACK);

? ? ? ? ? ? delay(3);

? ? ? ? ? }

? ? ? ? ? tft.fillRect(50, 193, 2, 10, WHITE);

? ? ? ? ? tft.setCursor(30, 206);

? ? ? ? ? tft.setTextColor(GREY, BLACK);

? ? ? ? ? tft.print("Po 0");

? ? ? ? ? tft.setCursor(110, 206);

? ? ? ? ? tft.print("25");

? ? ? ? ? tft.setCursor(162, 206);

? ? ? ? ? tft.print("50");

? ? ? ? ? tft.setCursor(255, 206);

? ? ? ? ? tft.print("100%");

? ? ? ? ? buttonPushCounter5 = 0;

? ? ? ? ? break;

? ? ? ? default:

? ? ? ? ? // if nothing else matches, do the default

? ? ? ? ? // default is optional

? ? ? ? ? break;

? ? ? }

? ? } else {

? ? ? // if the current state is LOW then the button

? ? ? // wend from on to off:

? ? }

? ? // Delay a little bit to avoid bouncing

? ? delay(50);

?}

?

? lastButtonState = buttonState;

? lastButtonState2 = buttonState2;

? lastButtonState3 = buttonState3;

? lastButtonState4 = buttonState4;

? lastButtonState5 = buttonState5;

?

? val1a = digitalRead( ROT_L1_PIN );

? val1b = digitalRead( ROT_R1_PIN );

? delay(1);

?

? // Rotary Encoder 1

? if ( val1a == HIGH && val1b == HIGH ) {

? ? if ( dirRot1 == ROT_LEFT ) {

? ? ? vfo += ROT_d;

? ? ? if (vfo > ROT_MAX) {

? ? ? ? vfo = ROT_MAX;

? ? ? }

? ? } else if ( dirRot1 == ROT_RIGHT ) {

? ? ? vfo -= ROT_d;

? ? ? if (vfo < ROT_MIN) {

? ? ? ? vfo = ROT_MIN;

? ? ? }

? ? }

? ? dirRot1 = ROT_STAY;

? } else {

? ? if ( val1a == LOW ) {

? ? ? dirRot1 = ROT_LEFT;

? ? }

? ? if ( val1b == HIGH ) {

? ? ? dirRot1 = ROT_RIGHT;

? ? }

? }

?

? if (oldMode != mode) {

? ? oldMode = mode;

? ? switch (mode) {

? ? ? // ? ? ? ?case 1:

? ? ? // ? ? ? ? ?Serial.println("1 Hz");

? ? ? // ? ? ? ? ?break;

? ? ? case 0:

? ? ? ? Serial.println("100 Hz");

? ? ? ? ROT_d = 100;

? ? ? ? tft.fillRect(195, 154, 50, 10, BLACK);

? ? ? ? tft.fillRect(155, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(129, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(212, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(75, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(230, 102, 20, 10, BLACK);

? ? ? ? tft.fillTriangle(190, 107, 185, 102, 195, 102, WHITE);

? ? ? ? tft.setFont();

? ? ? ? tft.setTextSize(1);

? ? ? ? tft.setCursor(215, 155);

? ? ? ? tft.setTextColor(GREY, BLACK);

? ? ? ? tft.println("100 Hz");

? ? ? ? break;

? ? ? case 1:

? ? ? ? Serial.println("1 ?KHz");

? ? ? ? ROT_d = 1000;

? ? ? ? tft.fillRect(205, 154, 50, 10, BLACK);

? ? ? ? tft.fillRect(184, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(129, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(212, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(64, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(230, 102, 20, 10, BLACK);

? ? ? ? tft.fillTriangle(165, 107, 160, 102, 170, 102, WHITE);

? ? ? ? tft.setFont();

? ? ? ? tft.setTextSize(1);

? ? ? ? tft.setCursor(220, 155);

? ? ? ? tft.setTextColor(GREY, BLACK);

? ? ? ? tft.println("1 KHz");

? ? ? ? break;

? ? ? case 2:

? ? ? ? Serial.println("10 KHz");

? ? ? ? ROT_d = 10000;

? ? ? ? tft.fillRect(205, 154, 50, 10, BLACK);

? ? ? ? tft.fillRect(155, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(212, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(64, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(230, 102, 20, 10, BLACK);

? ? ? ? tft.fillTriangle(139, 107, 134, 102, 144, 102, WHITE);

? ? ? ? tft.setFont();

? ? ? ? tft.setTextSize(1);

? ? ? ? tft.setCursor(215, 155);

? ? ? ? tft.setTextColor(GREY, BLACK);

? ? ? ? tft.println("10 KHz");

? ? ? ? break;

? ? ? case 3:

? ? ? ? Serial.println("1 Hz");

? ? ? ? ROT_d = 1;

? ? ? ? tft.fillRect(205, 154, 50, 10, BLACK);

? ? ? ? tft.fillRect(155, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(129, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(184, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(75, 102, 20, 10, BLACK);

? ? ? ? tft.fillTriangle(242, 107, 237, 102, 247, 102, WHITE);

? ? ? ? tft.setFont();

? ? ? ? tft.setTextSize(1);

? ? ? ? tft.setCursor(225, 155);

? ? ? ? tft.setTextColor(GREY, BLACK);

? ? ? ? tft.println("1 Hz");

? ? ? ? break;

? ? ? case 4:

? ? ? ? Serial.println("10 Hz");

? ? ? ? ROT_d = 10;

? ? ? ? tft.fillRect(205, 154, 50, 10, BLACK);

? ? ? ? tft.fillRect(155, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(129, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(184, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(230, 102, 20, 10, BLACK);

? ? ? ? tft.fillRect(184, 102, 20, 10, BLACK);

? ? ? ? tft.fillTriangle(218, 107, 213, 102, 223, 102, WHITE);

? ? ? ? tft.setFont();

? ? ? ? tft.setTextSize(1);

? ? ? ? tft.setCursor(220, 155);

? ? ? ? tft.setTextColor(GREY, BLACK);

? ? ? ? tft.println("10 Hz");

? ? ? ? break;

? ? }

? ? //Serial.print("sw:");

? ? //Serial.println(mode);

? }

?

? if (oldVal1 != vfo) {

? ? oldVal1 = vfo;

? ? tft.fillRect(68, 110, 190, 40, BLACK);

? ? tft.fillRect(92, 145, 3, 3, WHITE);

? ? tft.fillRect(176, 145, 3, 3, WHITE);

? ? tft.setTextSize(2);

? ? tft.setFont(&FreeSansBold12pt7b);

? ? tft.setCursor(70, 145);

? ? tft.setTextColor(WHITE, BLACK);

? ? tft.println(oldVal1 + 200);

? ? // Serial.println(vfo);

#ifdef IF_Offset

? ? uint32_t vco = bfo - (vfo * SI5351_FREQ_MULT);

? ? si5351.set_freq(vco, SI5351_PLL_FIXED, SI5351_CLK0);

? ? //you can also subtract the bfo to suit your needs

? ? //si5351.set_freq((vfo * SI5351_FREQ_MULT) + bfo ?, SI5351_PLL_FIXED, SI5351_CLK0);

? ? //

? ? // ? ?Serial.print("bfo : "); Serial.println(bfo);

? ? // ? ?Serial.print("vfo : "); Serial.println(vfo);

? ? // ? ?Serial.print("mult : "); Serial.println(int(SI5351_FREQ_MULT));

? ? // ? ?Serial.print("vco : "); Serial.println(vco);

? ? if (vfo >= 10000000ULL & tbfo != "USB")

? ? {

? ? ? bfo = USB;

? ? ? tbfo = "USB";

? ? ? si5351.set_freq( bfo, 0, SI5351_CLK2);

? ? ? Serial.println("We've switched from LSB to USB");

? ? }

? ? else if (vfo < 10000000ULL & tbfo != "LSB")

? ? {

? ? ? bfo = LSB;

? ? ? tbfo = "LSB";

? ? ? si5351.set_freq( bfo, 0, SI5351_CLK2);

? ? ? Serial.println("We've switched from USB to LSB");

? ? }

#endif

?

#ifdef Direct_conversion

? ? si5351.set_freq((vfo * SI5351_FREQ_MULT), SI5351_PLL_FIXED, SI5351_CLK0);

? ? tbfo = "";

#endif

?

#ifdef FreqX4

? ? si5351.set_freq((vfo * SI5351_FREQ_MULT) * 4, SI5351_PLL_FIXED, SI5351_CLK0);

? ? tbfo = "";

#endif

? ? delay(30);

? }

// DIGITAL STEP TUNING - SW1

? if ( digitalRead(ROT_SW1_PIN) ) {

? ? //delay(30);

? ? while (digitalRead(ROT_SW1_PIN)) {

? ? ? delay(1);

? ? }

? ? mode++;

? ? mode %= 5;

? }

}

?

Thanks. That's a lot of info to me. Will start looking in a very few minutes to what I can find.?

Again. Greatly appreciate the fast replies.?

Ron. ?

KJ4FFG?

On Tuesday, June 20, 2017, 10:14, Michael Hagen <motdog@...> wrote:

My first was the wooden box models with 2 heads.? This was 3 years ago.? $500 from So. El Monte Ca.

I made it simpler, removed a head and changed the extruder.?? Works good now.

Now I bought 2 more Hictops as kits.? I bought several extra parts as well a all metal extrusion head on eBay.

The Hictop brand on eBay is THE BEST for the money.? Get the ALL Aluminum model.? I got one because

it was repackaged and had some used parts.? At that time $229.? My friend bought several too.? Before he paid

$2k for a popular brand the doesn't make as big parts.

You can get them for about $300.?? You just can't beat them.? You have to build them.? I took days and had problems.

My friend spent a few hours!?? On a new one get 24 V PS, older was 12V like mine.? Get Auto Zero sensor too.

Some models they sold had the Z axes rods with just a simple thread.? Get the one with the Square thread.

But, I got changed mine for less than $20 by buying the Square ones and retrofitted.

I don't know about the filament counter, not needed.? They are programed with Arduino.? Just like Raduino!

I have programmed my several times, in fact I changed the whole board out when I had programming problems.

There is quite a learning curve.? There is a yahoo group and "Henry" is very helpful!

I also use Simply3D to convert STL files to print files.? Would never go back to the Free programs!

I would not like to be in the 3D printer business competing with these!? I a going to give my classic wooden box to a friend.

Mike, WA6ISP

On 6/20/2017 6:41 AM, R S via Groups.Io wrote:

What 3D printer are you folks using and sites or are they purchased locally to you? ?What are they priced at?

Thanks

Ron. KJ4FFG?

On Tuesday, June 20, 2017, 09:25, Michael Hagen <motdog@...> wrote:

I also used supports, the big Knob is hollowed out some places. I made
2, both came out perfect.? Simply3D makes me an Expert!

Takes a exacto knife to dig out the supports.

I love that program.? If you don't have a 6-32 tap, you can heat up a
long 6-32 screw (held in vice grips) and thread the holes.

Mike, WA6ISP

My first was the wooden box models with 2 heads.? This was 3 years ago.? $500 from So. El Monte Ca.

I made it simpler, removed a head and changed the extruder.?? Works good now.

Now I bought 2 more Hictops as kits.? I bought several extra parts as well a all metal extrusion head on eBay.

The Hictop brand on eBay is THE BEST for the money.? Get the ALL Aluminum model.? I got one because

it was repackaged and had some used parts.? At that time $229.? My friend bought several too.? Before he paid

$2k for a popular brand the doesn't make as big parts.

You can get them for about $300.?? You just can't beat them.? You have to build them.? I took days and had problems.

My friend spent a few hours!?? On a new one get 24 V PS, older was 12V like mine.? Get Auto Zero sensor too.

Some models they sold had the Z axes rods with just a simple thread.? Get the one with the Square thread.

But, I got changed mine for less than $20 by buying the Square ones and retrofitted.

I don't know about the filament counter, not needed.? They are programed with Arduino.? Just like Raduino!

I have programmed my several times, in fact I changed the whole board out when I had programming problems.

There is quite a learning curve.? There is a yahoo group and "Henry" is very helpful!

I also use Simply3D to convert STL files to print files.? Would never go back to the Free programs!

I would not like to be in the 3D printer business competing with these!? I a going to give my classic wooden box to a friend.

Mike, WA6ISP

On 6/20/2017 6:41 AM, R S via Groups.Io wrote:

What 3D printer are you folks using and sites or are they purchased locally to you? ?What are they priced at?

Thanks

Ron. KJ4FFG?

On Tuesday, June 20, 2017, 09:25, Michael Hagen <motdog@...> wrote:

I also used supports, the big Knob is hollowed out some places. I made
2, both came out perfect.? Simply3D makes me an Expert!

Takes a exacto knife to dig out the supports.

I love that program.? If you don't have a 6-32 tap, you can heat up a
long 6-32 screw (held in vice grips) and thread the holes.

Mike, WA6ISP

What 3D printer are you folks using and sites or are they purchased locally to you? ?What are they priced at?

Thanks

Ron. KJ4FFG?

On Tuesday, June 20, 2017, 09:25, Michael Hagen <motdog@...> wrote:

I also used supports, the big Knob is hollowed out some places. I made
2, both came out perfect.? Simply3D makes me an Expert!

Takes a exacto knife to dig out the supports.

I love that program.? If you don't have a 6-32 tap, you can heat up a
long 6-32 screw (held in vice grips) and thread the holes.

Mike, WA6ISP

Could be due to any or many of the following reasons:

1: Low audio drive - very likely (I use an amped Motorola mic and it goes up to 10W)

2: Low VFO or BFO levels

3: BFO frequency may need tweaking to suit the filter or your voice.

4: Low BiDi amp stage gain - unlikely

5: Low gain in final RF amp stages - short out R131 and see

Considering you get 5W it is not really low as you think!

Cheers
Raj

At 19/06/2017, you wrote:

HI All,

My original BITX never "aligned" correctly. In order to get the 1 amp current draw when hallooo'ing into the mic I had to crank R136 all the way. In that way I could get 5 watts out but only if running higher PA voltages.

xxx snip xxx

Thanks!

Jonathan - KK6RPX

I also used supports, the big Knob is hollowed out some places. I made
2, both came out perfect.? Simply3D makes me an Expert!

Takes a exacto knife to dig out the supports.

I love that program.? If you don't have a 6-32 tap, you can heat up a
long 6-32 screw (held in vice grips) and thread the holes.

Mike, WA6ISP