开云体育

Hello! The problem solved. Two 5k1 resistors at the fourth and tenth pads (per the picture above) did the job. Thanks, Matěj, for the lesson! Warm regards, Tony

Thanks for the heads up - yes I did read you post - thank you. I am one of the fortunate "buyers" who is fully aware of the pitfalls if and when making "faulty goods claims" on AliExpress (or eBay) -

Ok Marius, thank you very much for help, I’ll check that and report if I was successful.

Hi Joe, The same with me (AliExpress - Hisonauto) … but you‘re lost in space if you experience any trouble, have a look at my story: /g/ATU100/topic/89736113 I endeavoured the

Hey Ron, could you (or anyone else) point me to the file to print a front cover that can accept the .96 screen? Thanks!

Hello, After considerable research I am now the proud owner of an ATU-10 When you see this device “in your hand” – it’s truly amazing - WELL DONE David! I did not have the time nor my SMT

*Tony, Likewise wish i knew!??? I simply followed Davids original PCB. * I have updated my Sch to include the two 5k1 resistors if a PC with USC-C socket is used.?? PCB will be changed asap

So, ATU-10 just arrived yesterday for use with my IC-705. I've seen a couple of youtube vids... seemed easy enough to hook up and get going. Only thing is, I can't get it to work. So, when I begin a

Dear Matěj! I wish I knew that earlier, - when I modified the PCB ( /g/ATU100/message/1195 ) (to accommodate TQFP chip and AD8361 detectors)! So, as Chapter 5 tells, there should be

Hi Onno & Glenn, my PC had several crashes (OK … 14 years old, but still very suitable for Linux) and I moved the system to another hardware (also 14 years old ... :-) ...) … but now we move on:

Hi Tony! Devices equipped with a USB-C connector, which are power consumers, shall have the CC pins pulled down by pull-down resistors of 5.1kΩ. This informs the power supply that the device is a

Hi, It is mandatory to use BAT41 or 1N5711. You can also check the two 50 ohm resistors ... in general all the components that make up the tandem match, including the resistive divider. Check with a

Hey everyone, I have assembled my kit and I'm excited to work out a case for it. I found the STL for the 3d printed case but it appears to be designed around a different screen than was supplied with

Hi Marius, thanks for reply! I tested the diodes, and they seem to work ok, I would change them anyway but don’t have any appropriate low-drop Shottky (I suppose 1N4148 isn’t an option here?). Is

Dear Scott, Thanks for the reply. I've contacted David privately, hope he'll give an authoritative explanation. Regards, Tony

Tony, I noticed and reported this a while back. I think it is a limitation of the design. I am not a USB expert, but I looked at the schematic by VK3PE and it appears that only the USB 2.0 data lines

Hi Most likely BAT41 diodes need to be replaced. Something similar happened to me with a tuner, one diode was completely destroyed, the other was no longer in parameters. --- Cu ganduri bune, Marius -

Hello everyone, I’m having a problem with my atu-100, after almost 2 years of normal operation. Namely, I got pre-assembled atu-100 from China, and it was working fine, but suddenly it started

Hello! I have a laptop with both types of USB sockets - the USB type-A and USB type-C. When I connect ATU-10 (original N7DDC version) using the USB type-A to USB type-C cable - the connection works,

Yes, I have 9 of the VK3PE boards available for $5 postpaid in the USA. 73 Kees K5BCQ