开云体育

On Wed, Jan 10, 2024 at 02:51 PM, Jens wrote:

because all later versions are bad .

:)))))))))

Jens,

I don't use CW so I can't help you there.

With 0.19.0, I have no problem with my GPS USB Dongle. It works correctly, syncing my internal time to GPS.

I did a write-up a while back that described a step-by-step procedure to get the internal time synced to the GPS Dongle.

The main problem I would guess that people would have is their initial internal time (including the date and year) is not set up close enough to the GPS time. My write-up includes everything I do to get the GPS to sync the internal time.

Jerry K6ANI

Im using the latest version and the CW decoder works for me. ??

Hi Oleg,

First of all, thank you very much for your work. Some reports from me.

CW decoding does work for me, but I didn't try 0.17 to compare. It really decodes a lot of 'T' and 'E' but in general it works. It stops working when you set Filter low to 0Hz and starts working again when you set it higher.

First X6100 boot with freshly flashed SD card results with spectrum filling full height and no waterfall, but there is reception. Changing RF gain does nothing to the display. After reboot, everything works as expected.

There is something fishy with voice message recording - it does not record and does not play on the radio and does not tx out of the box - on the first boot. Also, seems rec gain is too high out of the box. After several restarts though I have managed to record a decent message and was able to play and TX it. Then I have tracked a bug to such scenario: boot, go to messages, send, play, everything works, then exit messaging app and long-press ATU to auto-tune the antenna. After this messages do not play (silence) and do not get sent (or gain is very low). Running SWR scan also disables messages.

While TXing message, HMic is active.

When you delete the last message, it is not cleared from the list.

Playback and record sliders in settings have a max value that's in the middle of the slider. I.e. if you set gain to max (full slider), you'll find it in the middle next time you switch to settings.

When I connect earphones to S/P port and Push PTT on HMic to transmit, I hear myself in earphones but pitch-shifted down. Event though Moni Level is set to 0. When I play recorded message, I hear normal voice, but while tx of voice message I also can hear pitch-shifted down ogre voice mixed with the recording. I have noticed, this is related to output power - more power, stronger the ogre voice during tx.

I have experienced spectrum and waterfall hangups several times. It seems to be related to VCO frequency display overlay. If I scroll too fast or the radio experiences a hickup due to switching to different ATU config or a very strong QRM happening and overloading the frontend while scrolling over frequencies fast, spectrum gets stuck and waterfall is not scrolling anymore. It updates just when changing frequency and then stops again. I have suspected frequency display overlay, so I switched it off and did not experience this problem after that.

Hope these bug reports will help, let me know if you need more details. Once again, thank you for your hard work. LY1MIC 73.

On Sun, Jan 14, 2024 at 11:56 PM, <albertas@...> wrote:

Then I have tracked a bug to such scenario: boot, go to messages, send, play, everything works, then exit messaging app and long-press ATU to auto-tune the antenna. After this messages do not play (silence) and do not get sent (or gain is very low). Running SWR scan also disables messages.

Yes, this is an old and well-known problem, I have written about it many times. Sometimes sound playback disappears if you switch to DIG modulation. So far I have not been able to overcome this. Only restarting the BB processor helps (this happens when the application is restarted by long pressing the Lock button)

Is there a simple way to lock the frequency? The lock button next to the VFO encoder does weird things. What am I missing? I love the firmware btu.

On Tue, Jan 16, 2024 at 01:52 AM, Facundo Fernandez wrote:

Is there a simple way to lock the frequency?

_Short_ press Lock button or SPCH/Lock button on HMic

On Mon, Jan 15, 2024 at 11:31 AM, Jens wrote:

CW Decoder works ABSOLUTLY NOT more in 0.19

In the science fiction story of the Strugatsky brothers from the times of the USSR, there was an episode when a reader wrote to a scientific journal: “I have been watching underground knocking in my basement for many years now. Please explain how it happens.” So, I don’t know how to fix the “underground knocks” ((((:

开云体育

On Tue, Jan 16, 2024 at 05:10 PM, Jens wrote:

Nothing works .

Еverything is working (;
?

开云体育

开云体育

On Fri, Jan 26, 2024 at 11:11 AM, Jens wrote:

what are Your decoder settings ??

Those that are by default

开云体育

开云体育

开云体育