开云体育

I've tried the DHCP method. It doesn't work for me.

Thanks Christian, that is what I used in trying to set it up. The problem is mostly my inexperience in networking? :-(

That could help ? https://www.radioddity.com/blogs/all/how-to-connect-xiegu-x6100-to-wfview-software?srsltid=AfmBOorRESblEKM5mZYNl82vw684YVN288kYXdvaJ5pmqZzviN-eksA7 73s Christian F8GHE

I tried using DHCP and Autoconnect. I think you can't enter the SSID manually - it is entered automatically when you select it from the list of SSIDs and press CONFIG.

Yeah that won't work.? Just use DHCP, autoconnect.? Make sure there are no spaces in the SSID, front, middle or back of the SSID.

Pretty sure that won’t work. You’ve got a class D IP, with different routing requirements. 192.168.5.18 and 192.168.1.4. Unfortunately, we can’t see the netmask in the x6100. If it’s

Here is how I have tried to configure the X6100 in WLAN settings. iolar is the SSID of my WiFi (Eero router). Password is my wifi password. 192.168.5.18 is the X6100 Reserved IP Address I entered into

I am totally confused about the X6100 WLAN SETTING. Should I set it up for my WiFi SSID, or for my X6100 SSID (assuming that is labelled ff07ab)? If the latter do I leave DNS Server box blank?

Thanks Frank. I use Fing, which does the same things. I also use Terminal.

Hi Denis, You may already know this but I use an IP scanner program to see what IPs are active on my LAN segments. I've used several but an open source one that I use often is AngryIP, available

I have tried setting my router to 2.4GHz only, but that is not the problem. In the x6100 WLAN Setting, should I see the X6100, and how is it labelled?? Is it likely to be ff07ab? I only see that and

Yes the IP Address I entered is within the range. Ping is ok with all devices except the omne in question. arp -a shows the device as (192.168.5.18) at <incomplete> on wlp4s0 But so do several other

2 or 3 times I saw no power output on AM - first press - power increases, than decreases, next press - no power. I guess, it's due to ALC working - switching to another mode and back to AM restores

WFview works best with an ethernet connection. Use a USB-ethernet adapter (any c-type that say they work with Linux/Raspberry Pi) and then look for that listing on your router. Works like a champ for

First - I have a new x6100 with latest firmware installed. I have NOT yet used the R1CBU firmware, I’m monitoring these threads to see what’s going on. DHCP does NOT work in stock firmware.

What do you mean you can see the x6100 but it doesn't have an IP Address?? Does that mean you can find the MAC address but the IP address is blank? Have you ever successfully connected the X6100 to

Make sure you choose a valid IP range. When i first got my x6100 it spit out a weird random IP that wasn’t even close to my other devices on my network. I ran arp -a in terminal on my desktop to

I can see the x6100 in my Eero6 router, but it doesn't show any ip address. So I entered an IP Reservation 192.168.5.12 I put that ip into the WFView settings. Still no connection. I have tried the

Where can I find the x6100 ip address for entering into WFView settings. I have looked in my router and see the x6100 but it does not give the ip address. My WiFi uses DHCP. My x6100 shows wifi

I am also running 1.9 and 1.6 r1. The first time I tried it yesterday it was giving me the low wattage readings, milliwatts. I redownloaded the r1 firmware and reinstalled it and power is back to