开云体育

see https://www.cqxiegu.com/productinfo/790911.html V1.1.7 Release Note Image File SHA256: BF153B10AB3D942060E65BE35A64A2D6C419A5EFF8D941E5C8CE93CE6DD44305 APP: ?V1.1.7 Jul 26 2023,11:50:55 BASE:

Real, No problem, I found the thermistor on the battery side (see photo). I measures the voltage of the centre pin (Vout) at ~12oC and it was ~ 0.63V ... The supply to the Vin was 5V. I wamed the

Hi Real, I have not measured this thermistor. I did not dismantle the chassis this far yet so I missed it. The thermistor looks like its pins go through the PCB to the battery side? Have you a photo

sorry for my google translate hihi, i'm think going to buy a scope to try to repair my x6100. Did you try to cool down the Low-Power Linear Active Thermistor with freeze. my to i believe its a

That is the firmware I am running. It is on the charger now, and has been for about 7 hours. Sent: Tuesday, August 8, 2023 2:12 PM To: [email protected] Subject: Re: [xiegu-x6100] EMPTY RED

Most current FW for X6100 is V1.1.6 Nov 2022. I hope you are not using a 3rd party FW. Go to the section displaying FW. 73, ron, n9ee/r Ron Wright, N9EE/RHernando Co ARES EC Spring Hill, Florida also

Morning Real, So once again I was able to observe the radio working as normal, only for it to stop. I have performed many measurements on the ATU. I observe each really/LPF activating correctly in

Thank you for the extra photos Real, I will check for this also in my tests this evening. Ciao for now, Scot

Scot, good match plan. I read on the forum that unplugging and reconnecting the ribbon cable can solve the problem, on my side it does not work it is mentioned that the ribbon cables are of very poor

Real, My radio shows same problem as yours. I can hear on SDR faint signal also. The ATU is a simple affair from looking at the chip (BU2152FS) on board - a simple SIPO serial in parallel out driver

I tried your find on my side, it gave me no results + my alc is still at 100 and no power on my dummy load, I noticed that there is a small audible transmission with my SDR dungle

Update to the last, this worked several times then the TX power was gone again. Time to fault find the ATU.

OK... I *"THOUGHT"* I HAD SOLVED THIS... This morning whilst operating CW and after playing with ATT and PRE amp I noticed ZERO - no power from the TX. The audio was fine as usual. After Real's last

Thank you Real for your reply! I will reflash the firmware first to see if this is an issue then! Maybe removing the battery for a long time will reset the ATU who knows! ? I have much test equipment

AFT05MS031N OLD PWR Trans inside x6100 drain - source = 3.96mohm dain - gate = 10.13kohm seems good After removed from x6100 drain - source =3.96mohm drain - gate = infinit seems good

Hi Real, did you fix this? Do you have a photo of the FUSE location? I also have ordered new final output. Thanks Scot

I’ll give it another chance. Thanks 73 N2GWK Sent: Saturday, August 5, 2023 6:49 PM To: [email protected] Subject: Re: [xiegu-x6100] EMPTY RED Battery icon after charge. I had the same problem

Thanks Dave but not necessary.? It operates fine, its just that pesky Icon and blinking light. Update, I did another Firmware update, same results, no change. Charging with OEM wall wart same

I had the same problem with my x6100 after an upgrade. I charged it, run it down to dead 4 times and that seemed to have fixed it. I now have a full battery charge showing when charged. Bobbi K4ARY

George, Sorry you are having problems with the X6100, I have a used unit that I have been using for about 2 months, you are welcome to borrow it and see if it works differently that your unit and use