开云体育

I hear BK is not really a prosign, but I'd like to make it one for the purpose of POTA. Is it doable? Also, I can't get the Farnsworth timing to zero-out in the Modem/CW/WinKeyer menu. It's stuck on

I use FLDigi to create and decode MFSK data for my show Pop Shop Radio. lately I have been sending a flag emoji next to a country name . In Tivar these decode percetly [image: image.png] In FLDigi

Hello George, Thanks for your friendly feedback! It's always good to know that the posted replies are actually read and even may be of some benefit, for a few at least... To your question, well,

Hello David, Thanks a lot for the new Alpha version 'fldigi ver4.2.06.27'. There are 2 more ITA2 Baudot shifts that would need to be implemented, please, since they still don't print correctly in

fldigi 4.2.06.27 development version available for testing Download at https://www.w1hkj.org/alpha/fldigi/ fldigi-4.2.06.27.tar.gz <https://www.w1hkj.org/alpha/fldigi/fldigi-4.2.06.27.tar.gz>

Hello Tobias, Thanks very much for the detail on the UI Scheme setting location.? It had moved from where it was previously located. I had already set the waterfall height to 100, which is the

Hello George, Please simply make your favorite setting in the 'Colors-Fonts - Buttons-Menus' section, see attachment. In case you care doing so, you can now even change the Menu font (and size!),

Please see the attached picture.

I just installed the latest FLDigi update (4.2.06) after not updating for a number of years.? Has the plastic-looking option been removed for displaying macro buttons, as described by Ed, W3NR,

Thank you David for your reply. Is this something that could be added in a future version of FLDigi? Regards, George

Hello Rich, Sounds like a great system to have all stations on the same page,so to speak. For comparison, we had our weekly DL0BS QTC here in Bavaria last night, as every Monday evening from 1900

GM, Tobias, Locally, when we start a digi net, NC sends a Tune. 1. This allows RX stations to adjust their radio+hardware sound card+CODEC+fldigi so that they have a clean sig in the SIG panel. I

The ITA2 character set is not a part of fldigi, but easily added (or substituted). You would have to modify the source code file rtty.cxx and recompile fldigi. David [email protected]> wrote:

Good morn' back to you, Rich. All agreed as you state it below. I guess the trailing center tone is intended for 'listeners' to help them center their receiver or fldigi offset. I don't see a

Good morn (here On the banks of the Piscataqua, anyway ;-) Thanks for the reply. Tobias earlier reported in a different thread on a related subject: "Your wav file signal looks exactly as expected: a

Hello George, I wasn't aware this 'reset' might happen once the values were manually set. To prevent any direct FLdigi induced modifications, you can, of course, edit the fldigi.prefs file and

What “mode” are you using when you see this? I think all Thor modes do send a string of characters ?to “clear the buffer” I hear it go fom low to high pitch tones like a trombone. Go to

Hello Tobias, Well the issue has returned with the wide gray area where the TX text was.? What is strange is that when I close the program the "int_tile_y_ratio:" is reset to 835, it's original

Hi George, Thanks a lot for sharing your experience. Since we kind of tweaked the 'standard' user interface behavior, it may well be that the full height is not updated until you restart FLdigi. So

I just tried it again after closing the program and things now work as they should.? I will keep an eye on it. Regards, George