开云体育

Hello Alex New version works in 48khz (very briefly checked), 96 khz comes up but it sounds like there is a much lower sensitivity (there is some activity on the panadpter but a lot less than on

I also have a 2 Khz wide unusable portion at the center of the passband. Mine is 30 db above the baseline, and the shape and bandwidth of the spike changes as I tune across the center frequency. I

Very nice, Alex. Considering the quality and innovative software you are known for, Rocky is a winner. My only suggestion is a wider filter esp. since 40m is such a hodge podge of adjacent

Thanks. Cecil Bayona KD5NWA www.qrpradio.com I fail to see why doing the same thing over and over and getting the same results every time is insanity: I've almost proved it isn't; only a few more

Try this also; Go in the control panel and run the "Sound and Audio Devices" Make sure all the voice and music devices are the sound card you want.

Hi Cecil, You can move the operating frequency to the center of the display by dragging the frequency scale (the gray bar under the spectrum). 73 Alex VE3NEA

Rocky looks really nice. Started up perfectly, and controls are very easy to understand. Now I just need my Softrock40, so i can get some sound out of this software. Guess I???m among the last on

I apologize for the problems that Rocky has with some soundcard types. The WDM audio interface is poorly documented, and I had to do some trial and error work to make the code open my Delta44. Other

Hello all. Had noise and zero spur (DC...) that were wide and strong (rendered a swat of 2 khz not usable around the LO freq.) Saw among the photos what N1RX did with a battery driven SR40

Was looking over Dan's Small Parts website and came across some 80 meter softrock crystals. I have no affiliation, either direct or indirect with Dans. 14.271 Mhz, 3.685 Mhz, HC-18, $1. 14.746 Mhz

I soldered all the connections again and my gnuradio software seem to pickup something from the little board. There is heavu QRM here in VU-land now. I connected a long wire as the antenna. Have to

Hello all Tried Asio4all didn't work for me (still the same error "unable to start input from usb soundblaster Audigy 2 NX"...). Anyway as I am intersted in SSB as well, ROCKY has (for the

I had the same problem with the "Rocky" software, and after I installed ASIO4ALL and made it the audio driver, the error then went away. I was using a different sound card, a SB Live 24. You can try

Has anyone tried using surface mount components vs pin-in-hole to see if there is any reduction in the above ? I'm using the external PS and will try surface mount in a few days. 73 Kees K5BCQ

I don't see how you expect to hear any stations without an antenna connected. You must get some kind of signal into the radio in order to hear something. Do you have a transmitter that you could

Hello Folks, I just got my Softrock40 kit assembled. I also wrote a GNURadio program to tune around the +-24khz BW. I plugged in the board and the green LED glows, but do not hear anything. The coax

Check out Yaesu FT101 parts on e-Bay. Just purchased a PT preselector for $12. The Drake R4-B/C also had a PT front end but parts are scarce and expensive. I've seen similar at Fair Radio. Dick

Oooops! Gotta remember to change addresses when I want to reply to a message that isn't intended for the group...[g] Chuck Carpenter, W5USJ, Point, TX -|- Rains Co. -|- EM22cv -|- 72 es 73 50 years

Here's what I see with this particular sound card. 57ad20.jpg Chuck Carpenter, W5USJ, Point, TX -|- Rains Co. -|- EM22cv -|- 72 es 73 50 years -|- 19 - K2OFN and 31 - W5USJ -|- Most fun = QRP since