开云体育

Mtr2000 wireline

dsay2001 All Messages By This Member #214342 I'm trying to figure out why our mtr2000 isn't passing any audio. We're using an external repeater controller through the wireline connector. This is new to us, and we're trying to get things set up before we go to the site. Before I try too hard and break something... Is that 4 pin connector (J6) supposed to come off? How do I release the wires? I tried pushing into one of the small holes, figuring that would release a clamp. The wires aren't budging. Thanks. Don
K6LOR.com All Messages By This Member #214346 Couple items to look at... Wireline card present in the top slot of the cage? Tuner menu Wireline TX audio level turned up (often found Zeroed out)? Set to Full Duplex? The black connector does not come off. You use a very small sturdy pin in the round hole above each wire slot that will release the clamp. I use a fairly large diode lead to pop mine open.? toggle quoted message Show quoted text On Sat, Apr 5, 2025, 17:31 dsay2001 via <don.sayler=[email protected]> wrote: I'm trying to figure out why our mtr2000 isn't passing any audio. We're using an external repeater controller through the wireline connector. This is new to us, and we're trying to get things set up before we go to the site. Before I try too hard and break something... Is that 4 pin connector (J6) supposed to come off? How do I release the wires? I tried pushing into one of the small holes, figuring that would release a clamp. The wires aren't budging. Thanks. Don
dsay2001 All Messages By This Member #214347 Thanks. I did finally figure that out. The guy we got this from had the wires stuffed into the square holes. I moved them to the round holes. I'm getting about 1.6vpp on the rx audio lines, that seems like plenty of audio. The cable from the mtr2k to a 9pin for the controller rings out properly, I'm seeing the 1.6vpp at the 9pin end. It's gotta be something in the controller.? That's for tomorrow.? toggle quoted message Show quoted text On Sat, Apr 5, 2025, 9:18 PM K6LOR.com via <aj.grantham=[email protected]> wrote: Couple items to look at... Wireline card present in the top slot of the cage? Tuner menu Wireline TX audio level turned up (often found Zeroed out)? Set to Full Duplex? The black connector does not come off. You use a very small sturdy pin in the round hole above each wire slot that will release the clamp. I use a fairly large diode lead to pop mine open.? On Sat, Apr 5, 2025, 17:31 dsay2001 via <don.sayler=[email protected]> wrote: I'm trying to figure out why our mtr2000 isn't passing any audio. We're using an external repeater controller through the wireline connector. This is new to us, and we're trying to get things set up before we go to the site. Before I try too hard and break something... Is that 4 pin connector (J6) supposed to come off? How do I release the wires? I tried pushing into one of the small holes, figuring that would release a clamp. The wires aren't budging. Thanks. Don
john ni0k All Messages By This Member #214350 开云体育 There is adequate documentation on the repeater-builder website. Don't forget to save the codeplug as received (you need a 32-bit Windows OS). Some programming settings are required for the wireline audio to work, and Moto's REALLY WEIRD audio alignment procedure. 73 -de "Curly" John NI0K call me: 6100271
Chris Boone WB5ITT All Messages By This Member #214355 You need to map external PTT to.the wireline audio in using the RSS.? Set it as a base and not repeater ..the external controller will work fine.? COS and PL detect out of the MTR are high going logic...ICS sells adapter boards that brings everything to a DB9 ..I'm using that on my MTR.. connects to my RLC and even provides 12V to the controller power plug Chris WB5ITT? toggle quoted message Show quoted text On Sun, Apr 6, 2025, 8:26 AM john ni0k via <jasimmons=[email protected]> wrote: There is adequate documentation on the repeater-builder website. Don't forget to save the codeplug as received (you need a 32-bit Windows OS). Some programming settings are required for the wireline audio to work, and Moto's REALLY WEIRD audio alignment procedure. 73 -de "Curly" John NI0K call me: 6100271
Chris Boone WB5ITT All Messages By This Member #214356 I run the RSS in a 32 bit Win XP VM using Virtual Box on my win10 64 bit laptops Have to watch the USB com port setting to match..works great toggle quoted message Show quoted text On Sun, Apr 6, 2025, 10:38 AM Christopher Boone <setxtelecom@...> wrote: You need to map external PTT to.the wireline audio in using the RSS.? Set it as a base and not repeater ..the external controller will work fine.? COS and PL detect out of the MTR are high going logic...ICS sells adapter boards that brings everything to a DB9 ..I'm using that on my MTR.. connects to my RLC and even provides 12V to the controller power plug Chris WB5ITT? On Sun, Apr 6, 2025, 8:26 AM john ni0k via <jasimmons=[email protected]> wrote: There is adequate documentation on the repeater-builder website. Don't forget to save the codeplug as received (you need a 32-bit Windows OS). Some programming settings are required for the wireline audio to work, and Moto's REALLY WEIRD audio alignment procedure. 73 -de "Curly" John NI0K call me: 6100271

Previous Topic Next Topic