开云体育

Anyone have any thoughts on this problem? Chad Nelson WI9HF/WRPL979 Janesville Wisconsin 608-754-8671 Send from my spectrum iPhone 16.

o.k., is quiet until it is on about a minute then gets a crackle kind of like bacon frying. Butch Bussen wa0vjr wa0vjr@... irlp 7135 allstar 56023 echolink 790800 new home phone 785 852-1102

I changed frequency to 442.100. But not sure about the crackle. I tried it here and didn't notice any noise on RX. Give me a call later on tomorrow, since leaving soon.

The repeater has a noise on receive like bacon frying. Not sure what is causing that. I can give you a call if you want to listen to it. kind of a crackling noise. I haven't tried adjusting anything

That's good to know thanks. Hopefully my little laptop comes by Wednesday because tentatively planning on going back to the site in portage on Thursday to visit the lady Buggs, well OK not really, but

yes, works fine. nvda is the best, although works with window-eyes as well. Butch Bussen wa0vjr wa0vjr@... irlp 7135 allstar 56023 echolink 790800 new home phone 785 852-1102

See, I told you lol. Glad it works. I had the incorrect model type when I tried to program it here, but just hit enter it went anyway with the serial cable. Chad Nelson WI9HF/WRPL979 Janesville

That was one of my questions I actually had and you might have just answered it for me, but, does your Windows XP box work with the KPG 91D software? Chad Nelson WI9HF/WRPL979 Janesville Wisconsin

Which version RSS are you using? Access needs to be set to pl, cor, etc...and it needs to be set as a repeater, not base as mentioned earlier [email protected]> wrote:

LDF5 was replaced with AVA5P and as noted, the older connectors are not compatible. The center remains hollow however. Matt AL0R Sent: Saturday, May 10, 2025 11:25 To: [email protected]

The computer I usually use doesn't have a serial port and I can't find my usb to serial adapter, so fired up my old xp machine with a for real serial port. Thanks all for your help. Good to know about

See Chris's comments about the fuse. BTW, the only reason to use the mic jack is if you're updating the firmware (or don't want to otherwise with the rear panel DB25). Good to hear you're good to go

I tried it on serial port on the back and it works, for some reason, not on the mike connector on the front which is what I use on my other repeaters. Thanks. Butch Bussen wa0vjr wa0vjr@... irlp

If the RJ mic jack has been shorted there is a 0ohm resistor that acts as a fuse...if it's blown, the program cable won't work..you can always use the DB25 Chris WB5ITT [email protected]> wrote:

I will weigh in with my resolution, I've always used a 25 pin serial cable the back of the repeater on the 25 pin accessory port and that's always worked fine. Chad Nelson WI9HF/WRPL979 Janesville

Do you already have an existing file loaded when you download?

If you post your codeplug, I’m sure several of the geniuses on here will gladly look at it for you. Will

that is what I thought, then why do I get that error? Butch Bussen wa0vjr wa0vjr@... irlp 7135 allstar 56023 echolink 790800 new home phone 785 852-1102

KPG-91D will work Ken ------------------------------------------------------------------------------ President and CTO - Arcom Controllers Makers of repeater controllers and accessories Phone: (503)

I thought my software for my 850 would work, but it says check radio model, retry. Does it take a different program? Thanks. Butch Bussen wa0vjr wa0vjr@... irlp 7135 allstar 56023 echolink